Next

Step 8

Diagnostic completed.

2.11.7.9 Battery Discharging Current Parasitic Load Test

If the battery continues to loss power, perform the following test to check whether there are parasitic battery current.

Note

Before carry out this procedure, please check whether there are installed after market equipments such as DVD, audio
power amplifier, subwoofer speaker box back and other non-original accessories. If there are, please Disconnect these
systems and then carry out this test procedure.

Warning!

Refer to "Battery Disconnection Warning" in "Warnings and Notices".

Step 1

Disconnect the battery negative cable. Refer to 

2.11.8.1

 

Battery Disconnection

.

Next

Step 2

With a digital multimeter, connect one end to the battery negative cable, the other to the negative battery
post.

Next

Step 3

Select digital multimeter's "current test" maximum range.

Next

Step 4

Left open the front door to observe the meter display readings.

Note

Do not carry out any other operations action at this time, otherwise
it is likely to damage the multimeter.

Next

Step 5

If the multimeter has no display, check whether the meter is damaged. If there is displayed reading, close
the left front door and press down the engine compartment button, press the remote control door lock button.

Next

Step 6

Observe the body Anti-theft system lamp the indicating system is in alert mode.

Next

Step 7

Wait for more than 10 min to observe the meter readings, (if the multimeter shows an abnormal reading,
tune the multimeter to minimum range). The reading should be below 30 mA. If the reading is higher than
30 mA, there may be parasitic current.

Engine

Starting / Charging System JL4G18-D

2-571

Note

When the system parasitic current can not be confirmed, compare the vehicle with a known good vehicle to helping
with diagnostic.

2.11.7.10 Jump Start Procedure

Warning!

Refer to "Battery Disconnection Warning" in "Warnings and Notices".

Step 1

Park the vehicle that will provide jump starting power properly to make sure the jumper cable can connect
two vehicles batteries.

Next

Step 2

Turn both vehicles' ignition switch to "OFF" position and turn off headlights and all the accessories power
supplies.

Next

Step 3

Press the hazard warning lamp switch, so that hazard warning lamps are on.

Next

Step 4

Apply two vehicles parking brake.

Next

Step 5

Make sure that the transmission gears are in neutral gear position.

Warning!

The jumper cable must be intact without exposed wires, otherwise
it will cause unnecessary personal injury or vehicle damage.

Next

Step 6

Connect one end of the red cable to the positive terminal of the battery with sufficient capacity providing the
power, and confirm that there is no contact with other metal parts.

Next

Step 7

Connect the other end of the red cable the positive terminal of the flat battery. Do not connect the red cable
to the negative terminal of flat battery.

Warning!

Do not connect the jumper cable directly to a flat battery negative
terminal to prevent the spark and possible battery gas explosion.

Next

Step 8

Connect one end of the black cable to the negative terminal of the battery with sufficient capacity providing
the power.

2-572

Starting / Charging System JL4G18-D

Engine

Next

Step 9

Finally, connect the other end of the black cable to the flat battery engine ground, and at least 500mm away
form the flat battery (19.7 in).

Next

Step 10

Start the vehicle, which has a battery with sufficient power, and run the engine speed at intermediate speed
for more than 3min.

Next

Step 11

Start the vehicle with the flat battery.

Next

Step 12

Remove the by jumper cables in reverse order.

Note

During the removal procedure, if the other end of the cable has not
been fully disconnected, avoid the cable clamp contact with any
metal objects.

Next

Step 13

Operation is completed.

Engine

Starting / Charging System JL4G18-D

2-573

2.11.8 Removal and Installation
2.11.8.1 Battery Disconnection

Disconnecting Procedure:

Warning!

Refer to "Battery Disconnection Warning" in "Warnings
and Notices".

 L

OCK     ACC

  

 O

N 

S

TA

RT

 L

OCK     ACC

  

 O

N 

S

T

AR

T

FE02-0406b

1.

Turn  off  all  electrical  equipments,  and  turn  the  ignition
switch to "OFF" position.

FE02-0407b

2.

Disconnect the battery negative cable.

2-574

Starting / Charging System JL4G18-D

Engine