Ford F-250 (2022 year). Manual in english

Brake Fluid Maintenance

Change the brake fluid.

Every three years

Perform this maintenance item every three years. Do not exceed the designated time

for the interval.

Brake fluid servicing requires special equipment available at your authorized dealer.

Other Maintenance Items

Replace the cabin air filter.

Every 20,000 mi
(32,180 km)

Replace the engine air filter.

Every 30,000 mi
(48,000 km)

Replace the front wheel bearing grease and grease seal, if
you use non-sealed bearings.

Every 60,000 mi
(96,000 km)

Replace the spark plugs.

Every 100,000 mi
(160,934 km)

Inspect the accessory drive belt or belts.

Every 100,000 mi
(160,934 km)

Change the automatic transmission fluid and filter on 6-speed
transmission. Consult dealer for requirements.

Every 150,000 mi
(240,000 km)

Replace the accessory drive belt or belts if not replaced within
the last 100,000 mi (160,000 km).

Replace the front wheel bearings and seals if you use non-
sealed bearings.

Change the axle(s) fluid. See exceptions.

Change the transfer case fluid, if applicable.

Change the engine coolant.

At 200,000 mi
(320,000 km)

If not replaced, inspect the belt or belts every 15,000 mi (24,000 km).

Initial replacement at 10 years or 200,000 mi (320,000 km), then every 5 years or

100,000 mi (160,000 km).

630

Scheduled Maintenance

SPECIAL OPERATING
CONDITIONS SCHEDULED
MAINTENANCE - DIESEL

If you operate your vehicle primarily in any
of the following conditions, you need to

perform extra maintenance as indicated.
If you operate your vehicle occasionally
under any of these conditions, it is not
necessary to perform the extra
maintenance. For specific
recommendations, see your dealership
service advisor or technician.

Towing a Trailer or Using a Car-top Carrier

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

See the axle maintenance items under

Exceptions

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km) or six months,
600 engine hours

Replace the wheel bearing grease and grease seals if using
non-sealed bearings. (Two-wheel drive vehicles)

Every 30,000 mi
(48,000 km)

Flush and refill the coolant.

At 60,000 mi (96,000 km)
or 2400 engine hours

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

Frequent or Extended Idling (Over 10 Minutes Per Hour of Normal Driving) or Frequent

Low-speed Operation if your Vehicle is Used for Stationary Operation

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Flush and refill the coolant.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

631

Scheduled Maintenance

Frequent Low-speed Operation, Consistent Heavy Traffic Under 25 mph (40 km/h) or

Long Rush-hour Traffic

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Flush and refill the coolant.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

Sustained High-speed Driving at Gross Vehicle Weight Rating (Maximum Loaded Weight

for Vehicle Operation)

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Replace the wheel bearing grease and grease seals if using
non-sealed bearings. (Two-wheel drive vehicles)

Every 30,000 mi
(48,000 km)

Flush and refill the coolant.

Every 60,000 mi
(96,000 km) or 2400
engine hours

Note:

After the initial coolant flush and fill at 60,000 mi (96,000 km) or 2400 engine

hours, flush and fill every 45,000 mi (72,000 km) or 1800 engine hours thereafter.

632

Scheduled Maintenance

Operating in Sustained Ambient Temperatures Below -9°F (-23°C) or Above 100°F (38°C)

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Replace the wheel bearing grease and grease seals if using
non-sealed bearings. (Two-wheel drive vehicles)

Every 30,000 mi
(48,000 km)

Operating in Dusty or Sandy Conditions (Such as Unpaved or Dusty Roads)

Rotate the tires, inspect the tires for wear and measure

tread depth.

Every 7,500 mi (12,000 km)

Inspect the brake system pads and rotors.

Inspect the air filter restriction gauge. Replace the filter if
necessary.

Inspect the steering and suspension ball joints and tie rods.
Lubricate any grease fittings.

Change the engine oil and filter.

Every 7,500 mi (12,000 km),
six months or 300 engine
hours

Inspect and lubricate the U-joints.

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), 6 months or
600 engine hours

Replace the air inlet foam filter.

Every 30,000 mi
(48,000 km)

Replace the wheel bearing grease and grease seals if using
non-sealed bearings. (Two-wheel drive vehicles)

Rotate the front wheels on vehicles with dual rear wheels when specified. Rotate the

rear wheels if unusual wear is noted.

Reset the Oil Change Reminder after engine oil and filter changes.

633

Scheduled Maintenance

Off-road Operation

Inspect functional holes in each leg of the twin exhaust
tips and the holes under the shield just inboard of the right
rear tire to make sure they are clean and clear of debris or
foreign materials. Refer to the Vehicle Care chapter of your
owner’s manual for more information.

As required

Inspect the steering and suspension ball joints and tie rods.
Lubricate any grease fittings.

Rotate the tires, inspect the tires for wear and measure

tread depth.

Every 7,500 mi (12,000 km),
six months or 300 engine
hours

Inspect the brake system pads and rotors.

Inspect the air filter restriction gauge. Replace the filter if
necessary.

Change the engine oil and filter.

Every 7,500 mi (12,000 km)
or 300 engine hours

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
600 engine hours

Replace the air inlet foam filter.

Every 30,000 mi
(48,000 km)

Replace the wheel bearing grease and grease seals if using
non-sealed bearings. (Two-wheel drive vehicles).

Change the rear axle fluid (Dana rear axles only - some F-
350s; all F-450s and F-550s).

Every 50,000 mi
(80,000 km)

Change the transfer case fluid. (Four-wheel drive vehicles)

Inspect the front axle fluid. (Four-wheel drive vehicles)

Vehicles with dual rear wheels should rotate the front wheels when specified; rear wheels

only if unusual wear is noted.

Reset the Oil Change Reminder after engine oil and filter changes.

634

Scheduled Maintenance

Using Biodiesel, up to and Including 20% Biodiesel (B20)

Change the engine oil and filter as indicated by the
information display, and perform the services listed in the
scheduled maintenance chart.

As required

Replace the engine-mounted and frame-mounted fuel
filters.

Every 15,000 mi
(24,000 km), six months or
300 engine hours

Using Fuel Other Than Ultra-low Sulfur Diesel Fuel - Vehicles Operated Where Ultra-low

Sulfur Diesel Fuel is not Required or Available

Change engine oil and filter.

Every 2,500 mi (4,000 km)
or three months (if using
high sulfur fuel with more
than 500 ppm sulfur)

Change engine oil and filter.

Every 5,000 mi (8,000 km)
or six months (if using high
sulfur fuel with fewer than
500 ppm sulfur)

Exceptions

Axle and Transfer Case Maintenance

Axle(s) and transfer case (4X4 only) fluid
changes or level checks are not required
unless a leak is suspected or the assembly
has been submerged in water. During long
periods of trailer towing with outside
temperatures above 70°F (21°C) or at
wide-open throttle for long periods above
45 mph (72 km/h), change the rear axle
fluid every 30,000 mi (48,000 km) if the
rear axle is filled with non-synthetic fluid.
This interval can be waived and the
150,000 mi (240,000 km) service interval
can continue if the rear axle is filled with
75W140 synthetic gear fluid meeting Ford

specification WSL-M2C192-A, part number
XY-75W140-QL, or equivalent. Add friction
modifier XL-3 (EST-M2C118-A) or
equivalent for complete refill of
Traction-Lok rear axles. See

Capacities

and Specifications

(page 467).

Additional Axle Maintenance for Dual
Rear Wheels

Change rear axle fluid every 250,000 mi
(400,000 km) under normal driving
conditions on all commercial applications.
When operating your vehicle at or near
maximum gross vehicle weights, change
the rear axle fluid every 60,000 mi
(96,000 km). In addition, follow this
60,000 mi (96,000 km) schedule when
operating your vehicle under the special
operating conditions where noted.

635

Scheduled Maintenance

California Fuel Filter Replacement

If you register your vehicle in California, the
California Air Resources Board has
determined that the failure to perform this
maintenance item does not nullify the
emission warranty or limit recall liability
before the completion of your vehicle's
useful life. Ford Motor Company, however,
urges you to have all recommended
maintenance services performed at the
specified intervals and to record all vehicle
service.

Hot Climate Oil Change Intervals

Vehicles operating in the Middle East,
North Africa, Sub-Saharan Africa or
locations with similar climates using an
American Petroleum Institute (API)
Certified for Gasoline Engines (Certification
mark) oil of SM or SN quality, the normal
oil change interval is 3,000 mi (5,000 km).

If the available API SM or SN oils are not
available, then the oil change interval is
2,000 mi (3,000 km).

Engine Air Filter and Cabin Air Filter
Replacement

The life of the engine air filter and cabin air
filter is dependent on exposure to dusty
and dirty conditions. Vehicles operated in
these conditions require frequent
inspection and replacement of the engine
air filter and cabin air filter.

Diesel Particulate Filter

Over time, a slight amount of ash builds
up in the diesel particulate filter, which is
not removed during the regeneration
process. The filter may need to be replaced
with a new or remanufactured part at
approximately 250,000 mi (400,000 km).
Actual mileage varies depending on engine
and vehicle operating conditions.

In this case, the engine control system sets
a service light (wrench icon) to inform you
to bring your vehicle to the dealer for
service. If there are any issues with the
oxidation catalyst or particulate filter
system, a service light (wrench or engine
icon) sets by the engine control system to
inform you to bring your vehicle into a
dealer for service.

SPECIAL OPERATING
CONDITIONS SCHEDULED
MAINTENANCE - GASOLINE

If you operate your vehicle primarily in any
of the following conditions, you need to
perform extra maintenance as indicated.
If you operate your vehicle occasionally
under any of these conditions, it is not
necessary to perform the extra
maintenance. For specific
recommendations, see your dealership
service advisor or technician.

Towing a Trailer or Using a Car-top Carrier

Inspect and lubricate U-joints if equipped with grease
fittings.

Inspect frequently, service
as required

See axle maintenance items under

Exceptions

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Every 5,000 mi (8,000 km)

Rotate tires, inspect tires for wear and measure tread

depth.

636

Scheduled Maintenance

Towing a Trailer or Using a Car-top Carrier

Change engine oil and filter.

Every 5,000 mi (8,000 km)
or six months.

Inspect and lubricate U-joints if equipped with grease
fittings.

Replace front wheel bearing grease and grease seals if
non-sealed bearings are used.

Every 30,000 mi
(48,000 km)

Change transfer case fluid (Four-wheel drive vehicles).

Every 60,000 mi
(96,000 km)

Replace spark plugs.

Rotate the front wheels on vehicles with dual rear wheels when specified. Rotate the

rear wheels if unusual wear is noted.

Extensive Idling or Low-speed Driving for Long Distances, as in Heavy Commercial Use

(Such as Delivery, Taxi, Patrol Car or Livery)

Replace engine air filter.

Inspect frequently, service
as required

Replace cabin air filter.

Inspect brake system.

Every 5,000 mi (8,000 km)

Inspect wheels and related components for abnormal
noise, wear, looseness or drag.

Lubricate control arm and steering ball joints if equipped
with grease fittings.

Rotate tires, inspect tires for wear and measure tread

depth.

Inspect and lubricate U-joints if equipped with grease
fittings.

Every 5,000 mi (8,000 km)
or six months

Change engine oil and filter.

Every 5,000 mi (8,000 km)
or six months or 200 engine
hours.

Replace front wheel bearing grease and grease seals if
non-sealed bearings are used.

Every 30,000 mi
(48,000 km)

Replace spark plugs.

Every 60,000 mi
(96,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Rotate the

rear wheels if unusual wear is noted.

637

Scheduled Maintenance

Operating in Dusty or Sandy Conditions (Such as Unpaved or Dusty Roads)

Replace engine air filter.

Inspect frequently, service
as required

Replace cabin air filter.

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Every 5,000 mi (8,000 km)

Rotate tires, inspect tires for wear and measure tread

depth.

Change engine oil and filter.

Every 5,000 mi (8,000 km)
or six months

Inspect and lubricate U-joints if equipped with grease
fittings.

Replace front wheel bearing grease and grease seals if
non-sealed bearings are used.

Every 30,000 mi
(48,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Rotate the

rear wheels if unusual wear is noted.

Off-road operation

Inspect steering linkage, ball joints and U-joints, Lubricate
if equipped with grease fittings.

Inspect frequently, service
as required

Replace engine air filter.

Change engine oil and filter.

Every 5,000 mi (8,000 km)
or six months

Replace cabin air filter.

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.

Rotate tires, inspect tires for wear and measure tread

depth.

Replace front wheel bearing grease and grease seals if
non-sealed bearings are used.

Every 30,000 mi
(48,000 km)

Rotate the front wheels on vehicles with dual rear wheels when specified. Rotate the

rear wheels if unusual wear is noted.

638

Scheduled Maintenance

Exclusive use of E85 (Flex Fuel Vehicles Only)

If ran exclusively on E85, fill the fuel tank full with regular
unleaded fuel.

Every oil change interval

Exceptions

Axle and Transfer Case Maintenance

Capacities

and Specifications

(page 467).

Additional Axle Maintenance for Dual
Rear Wheels

California Fuel Filter Replacement

Hot Climate Oil Change Intervals

If the available API SM or SN oils are not
available, then the oil change interval is
2,000 mi (3,000 km).

Engine Air Filter and Cabin Air Filter
Replacement

639

Scheduled Maintenance

ROLLOVER WARNING

WARNING:

Utility vehicles have a

significantly higher rollover rate than
other types of vehicles.

WARNING:

Vehicles with a higher

center of gravity (utility and four-wheel
drive vehicles) handle differently than
vehicles with a lower center of gravity
(passenger cars). Avoid sharp turns,
excessive speed and abrupt steering in
these vehicles. Failure to drive cautiously
increases the risk of losing control of your
vehicle, vehicle rollover, personal injury
and death.

WARNING:

In a rollover crash, an

unbelted person is significantly more
likely to die than a person wearing a
seatbelt.

WARNING:

Do not become

overconfident in the ability of four-wheel
drive vehicles. Although a four-wheel
drive vehicle may accelerate better than
a two-wheel drive vehicle in low traction
situations, it won't stop any faster than
two-wheel drive vehicles. Always drive
at a safe speed.

Utility vehicles and trucks handle
differently than passenger cars in the
various driving conditions that are
encountered on streets, highways and
off-road. Utility vehicles and trucks are not
designed for cornering at speeds as high
as passenger cars any more than low-slung
sports cars are designed to perform
satisfactorily under off-road conditions.

OUR SUSTAINABILITY
REPORT

You should play your part in protecting the
environment. Correct vehicle usage and
the authorized disposal of waste, cleaning
and lubrication materials are significant
steps toward this aim.

For additional information about our
sustainability progress and initiatives, visit

www.sustainability.ford.com

THE BETTER BUSINESS
BUREAU AUTO LINE
PROGRAM - UNITED STATES
OF AMERICA

Your satisfaction is important to Ford
Motor Company and to your dealer. If a
warranty concern has not been resolved
using the three-step procedure outlined
earlier in this chapter in the Getting the
Services you need section, you may be
eligible to participate in the BBB AUTO
LINE program.

The BBB AUTO LINE program consists of
two parts – mediation and arbitration.
During mediation, a representative of the
BBB will contact both you and Ford Motor
Company to explore options for settlement
of the claim. If an agreement is not reached
during mediation or you do not want to
participate in mediation, and if your claim
is eligible, you may participate in the
arbitration process. An arbitration hearing
will be scheduled so that you can present
your case in an informal setting before an
impartial person. The arbitrator considers
the testimony provided and makes a
decision after the hearing.

640

Customer Information

Disputes submitted to the BBB AUTO LINE
program are usually decided within 40
days after you file your claim with the BBB.
You are not bound by the decision, and
may reject the decision and proceed to
court where all findings of the BBB Auto
Line dispute, and decision, are admissible
in the court action. Should you choose to
accept the BBB AUTO LINE decision, Ford
is then bound by the decision, and must
comply with the decision within 30 days
of receipt of your acceptance letter.

BBB AUTO LINE Application: Using the
information that follows, please call or
write to request a program application.
You will be asked for your name and
address, general information about your
new vehicle, information about your
warranty concerns, and any steps you have
already taken to try to resolve them. A
Customer Claim Form will be mailed that
needs to be completed, signed and
returned to the BBB along with proof of
ownership. Upon receipt, the BBB reviews
the claim for eligibility under the Program
Summary Guidelines.

You can get more information by
calling BBB AUTO LINE at
1-800-955-5100, or writing to:

BBB AUTO LINE a Division of BBB
National Programs, Inc.
1676 International Drive, Suite 550
McLean, VA 22102

BBB AUTO LINE applications can also be
requested by calling the Ford Motor
Company Customer Relationship Center
at 1-800-392-3673.

For additional information, refer to the
Better Business Bureau website.

Note:

Ford Motor Company reserves the

right to change eligibility limitations, modify
procedures, or to discontinue this process
at any time without notice and without
obligation.

THE MEDIATION AND
ARBITRATION PROGRAM -
CANADA

For vehicles delivered to authorized
Canadian dealers. In those cases where
you continue to feel that the efforts by Ford
of Canada and the authorized dealer to
resolve a factory-related vehicle service
concern have been unsatisfactory, Ford of
Canada participates in an impartial third
party mediation/arbitration program
administered by the Canadian Motor
Vehicle Arbitration Plan (CAMVAP).

The CAMVAP program is a straightforward
and relatively speedy alternative to resolve
a disagreement when all other efforts to
produce a settlement have failed. This
procedure is without cost to you and is
designed to eliminate the need for lengthy
and expensive legal proceedings.

In the CAMVAP program, impartial
third-party arbitrators conduct hearings at
mutually convenient times and places in
an informal environment. These impartial
arbitrators review the positions of the
parties, make decisions and, when
appropriate, render awards to resolve
disputes. CAMVAP decisions are fast, fair,
and final as the arbitrator’s award is
binding on both you and Ford of Canada.

CAMVAP services are available in all
Canadian territories and provinces. For
more information, without charge or
obligation, call your CAMVAP Provincial
Administrator directly at 1-800-207-0685
or visit www.camvap.ca.

ORDERING A CANADIAN
FRENCH OWNER'S MANUAL

You can obtain a French owner's manual
from an authorized dealer or by contacting
Helm, LLC at:

641

Customer Information

MOBILE COMMUNICATIONS
EQUIPMENT

WARNING:

Driving while distracted

can result in loss of vehicle control, crash
and injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the
safe operation of your vehicle. We
recommend against the use of any
hand-held device while driving and
encourage the use of voice-operated
systems when possible. Make sure you
are aware of all applicable local laws
that may affect the use of electronic
devices while driving.

Using mobile communications equipment
is becoming increasingly important in the
conduct of business and personal affairs.
However, you must not compromise your
own or others’ safety when using such
equipment. Mobile communications can
enhance personal safety and security when
appropriately used, particularly in
emergency situations. Safety must be
paramount when using mobile
communications equipment to avoid
negating these benefits. Mobile
communication equipment includes, but
is not limited to, cellular phones, pagers,
portable email devices, text messaging
devices and portable two-way radios.

END USER LICENSE
AGREEMENT

VEHICLE SOFTWARE END USER
LICENSE AGREEMENT (EULA)

•

You (“You” or “Your” as applicable)
have acquired a vehicle having several
devices, including SYNC ® and various
control modules, ("DEVICES") that
include software licensed or owned by
Ford Motor Company and its affiliates
("FORD MOTOR COMPANY"). Those
software products of FORD MOTOR
COMPANY origin, as well as associated
media, printed materials, and "online"
or electronic documentation
("SOFTWARE") are protected by
international intellectual property laws
and treaties. The SOFTWARE is
licensed, not sold. All rights reserved.

•

The SOFTWARE may interface with
and/or communicate with, or may be
later upgraded to interface with and/or
communicate with additional software
and/or systems provided by FORD
MOTOR COMPANY.

IF YOU DO NOT AGREE TO THIS END
USER LICENSE AGREEMENT ("EULA")
DO NOT USE THE DEVICES OR COPY
THE SOFTWARE. ANY USE OF THE
SOFTWARE, INCLUDING BUT NOT
LIMITED TO USE ON THE DEVICES,
WILL CONSTITUTE YOUR AGREEMENT
TO THIS EULA (OR RATIFICATION OF
ANY PREVIOUS CONSENT).

GRANT OF SOFTWARE LICENSE:

This

EULA grants you the following license:

•

You may use the SOFTWARE as
installed on the DEVICES and as
otherwise interfacing with systems
and/or services provide by or through
FORD MOTOR COMPANY or its third
party software and service providers.

685

Customer Information

Description of Other Rights and
Limitations

•

Speech Recognition:

If the

SOFTWARE includes speech
recognition component(s), you should
understand that speech recognition is
an inherently statistical process and
that recognition errors are inherent in
the process. Neither FORD MOTOR
COMPANY nor its suppliers shall be
liable for any damages arising out of
errors in the speech recognition
process. It is your responsibility to
monitor any speech recognition
functions included in the system.

•

Limitations on Reverse Engineering,
Decompilation and Disassembly:

You may not reverse engineer,
decompile, translate, disassemble or
attempt to discover any source code
or underlying ideas or algorithms of the
SOFTWARE nor permit others to
reverse engineer, decompile or
disassemble the SOFTWARE, except
and only to the extent that such activity
is expressly permitted by applicable
law notwithstanding this limitation or
to the extent as may be permitted by
the licensing terms governing use of
any open source components included
with the SOFTWARE.

•

Limitations on Distributing,
Copying, Modifying and Creating
Derivative Works:

You may not

distribute, copy, make modifications
to or create derivative works based on
the SOFTWARE, except and only to the
extent that such activity is expressly
permitted by applicable law
notwithstanding this limitation or to
the extent as may be permitted by the
licensing terms governing use of any
open source components included with
the SOFTWARE.

•

Single EULA:

The end user

documentation for the DEVICES and
related systems and services may
contain multiple EULAs, such as
multiple translations and/or multiple
media versions (e.g., in the user
documentation and in the software).
Even if you receive multiple EULAs, you
are licensed to use only one (1) copy of
the SOFTWARE.

•

SOFTWARE Transfer:

You may

permanently transfer your rights under
this EULA only as part of a sale or
transfer of the DEVICES, provided you
retain no copies, you transfer all of the
SOFTWARE (including all component
parts, the media and printed materials,
any upgrades, and, if applicable, the
Certificate(s) of Authenticity), and the
recipient agrees to the terms of this
EULA. If the SOFTWARE is an upgrade,
any transfer must include all prior
versions of the SOFTWARE.

•

Termination:

Without prejudice to any

other rights, FORD MOTOR COMPANY
may terminate this EULA if you fail to
comply with the terms and conditions
of this EULA.

•

Internet-Based Services
Components:

The SOFTWARE may

contain components that enable and
facilitate the use of certain
Internet-based services. You
acknowledge and agree that FORD
MOTOR COMPANY, third party
software and service suppliers, its
affiliates and/or its designated agent
may automatically check the version
of the SOFTWARE and/or its
components that you are utilizing and
may provide upgrades or supplements
to the SOFTWARE that may be
automatically downloaded to your
DEVICES.

686

Customer Information

•

Additional Software/Services:

The

SOFTWARE may permit FORD MOTOR
COMPANY, third party software and
service suppliers, its affiliates and/or
its designated agent to provide or make
available to you SOFTWARE updates,
supplements, add-on components, or
Internet-based services components
of the SOFTWARE after the date you
obtain your initial copy of the
SOFTWARE ("Supplemental
Components".) SOFTWARE updates
may cause you to incur additional
charges from your wireless service
provider. If FORD MOTOR COMPANY
or third party software and services
suppliers provide or make available to
you Supplemental Components and
no other EULA terms are provided
along with the Supplemental
Components, then the terms of this
EULA shall apply. FORD MOTOR
COMPANY, its affiliates and/or its
designated agent reserve the right to
discontinue without liability any
Internet-based services provided to
you or made available to you through
the use of the SOFTWARE.

•

Links to Third Party Sites:

The

SOFTWARE may provide you with the
ability to link to third party sites. The
third party sites are not under the
control of FORD MOTOR COMPANY,
its affiliates and/or its designated
agent. Neither FORD MOTOR
COMPANY nor its affiliates nor its
designated agent are responsible for
(I) the contents of any third party sites,
any links contained in third party sites,
or any changes or updates to third
party sites, or (ii) webcasting or any
other form of transmission received
from any third party sites. If the
SOFTWARE provides links to third
party sites, those links are provided to
you only as a convenience, and the
inclusion of any link does not imply an
endorsement of the third party site by
FORD MOTOR COMPANY, its affiliates
and/or its designated agent.

•

Obligation to Drive Responsibly:

You recognize your obligation to drive
responsibly and keep attention on the
road. You will read and abide with the
DEVICES operating instructions
particularly as they pertain to safety
and you agree to assume any risk
associated with the use of the
DEVICES.

UPGRADES AND RECOVERY MEDIA:

If the SOFTWARE is provided by FORD
MOTOR COMPANY separate from the
DEVICES on media such as a ROM chip,
CD ROM disk(s) or via web download or
other means, and is labeled "For Upgrade
Purposes Only" or "For Recovery Purposes
Only" you may install one (1) copy of such
SOFTWARE onto the DEVICES as a
replacement copy for the existing
SOFTWARE, and use it in accordance with
this EULA, including any additional EULA
terms accompanying the upgrade
SOFTWARE.

687

Customer Information

INTELLECTUAL PROPERTY RIGHTS:

All title and intellectual property rights in
and to the SOFTWARE (including but not
limited to any images, photographs,
animations, video, audio, music, text and
"applets" incorporated into the
SOFTWARE), the accompanying printed
materials, and any copies of the
SOFTWARE, are owned by FORD MOTOR
COMPANY, or its affiliates or suppliers. The
SOFTWARE is licensed, not sold. You may
not copy the printed materials
accompanying the SOFTWARE. All title
and intellectual property rights in and to
the content which may be accessed
through use of the SOFTWARE is the
property of the respective content owner
and may be protected by applicable
copyright or other intellectual property
laws and treaties. This EULA grants you no
rights to use such content outside its
intended use. All rights not specifically
granted under this EULA are reserved by
FORD MOTOR COMPANY, its affiliates,
and third party software and service
providers and suppliers. Use of any on-line
services which may be accessed through
the SOFTWARE may be governed by the
respective terms of use relating to such
services. If this SOFTWARE contains
documentation that is provided only in
electronic form, you may print one copy of
such electronic documentation.

EXPORT RESTRICTIONS:

You

acknowledge that the SOFTWARE is
subject to U.S. and European Union export
jurisdiction. You agree to comply with all
applicable international and national laws
that apply to the SOFTWARE, including
the U.S. Export Administration Regulations,
as well as end-user, end-use and
destination restrictions issued by U.S. and
other governments.

TRADEMARKS:

This EULA does not grant

you any rights in connection with any
trademarks or service marks of FORD
MOTOR COMPANY, its affiliates, and third
party software and service providers.

PRODUCT SUPPORT:

Please refer to

FORD MOTOR COMPANY instructions
provided in the documentation for the
DEVICES product support, such as the
vehicle owner guide.

Should you have any questions concerning
this EULA, or if you desire to contact FORD
MOTOR COMPANY for any other reason,
please refer to the address provided in the
documentation for the DEVICES.

No Liability for Certain Damages:

EXCEPT AS PROHIBITED BY LAW, FORD
MOTOR COMPANY, ANY THIRD PARTY
SOFTWARE OR SERVICES SUPPLIERS,
AND THEIR AFFILIATES SHALL HAVE NO
LIABILITY FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL OR INCIDENTAL
DAMAGES ARISING FROM OR IN
CONNECTION WITH THE USE OR
PERFORMANCE OF THE SOFTWARE. THIS
LIMITATION SHALL APPLY EVEN IF ANY
REMEDY FAILS OF ITS ESSENTIAL
PURPOSE. THERE ARE NO WARRANTIES
OTHER THAN THOSE THAT MAY BE
EXPRESSLY PROVIDED FOR YOUR NEW
VEHICLE.

SYNC® Automotive Important Safety
Information Read and follow
instructions:

•

Before using your SYNC® system, read
and follow all instructions and safety
information provided in this end user
manual ("Owner Guide".) Not
following precautions found in the
Owner Guide can lead to an accident
or other serious injuries.

688

Customer Information

Ford F-250 (2022 year). Manual in english - page 39