Mercury Milan (2011 year). Manual

GAUGES

Standard instrument cluster shown, metric and optional clusters
similar

Speedometer: Indicates the
current vehicle speed.

Engine coolant temperature
gauge: Indicates engine coolant
temperature. At normal operating
temperature, the needle will be in
the normal range (between “H” and
“C”). If it enters the red section,
the engine is overheating. Stop
the vehicle as soon as safely
possible, switch off the engine and let the engine cool.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

WARNING: Never remove the coolant reservoir cap while the
engine is running or hot.

Fuel gauge: Indicates
approximately how much fuel is left
in the fuel tank (when the ignition
is in the on position). The fuel
gauge may vary slightly when the
vehicle is in motion or on a grade.

The fuel icon and arrow indicates
which side of the vehicle the fuel
filler door is located.

Refer to Filling the tank in the Maintenance and Specifications
chapter for more information.

Tachometer: Indicates the engine
speed in revolutions per minute.
Driving with your tachometer
pointer continuously at the top of
the scale may damage the engine.

Odometer: Registers the total miles
(kilometers) of the vehicle.

Refer to Message center in the
Instrument cluster chapter on how
to switch the display from Metric to
English.

Trip odometer: Registers the miles
(kilometers) of individual journeys.
Press and release the message
center INFO button until TRIP A or
TRIP B appears in the display (this
represents the trip mode). Press
and hold the RESET button for two seconds to reset.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

MESSAGE CENTER

Your vehicle’s message center allows you to configure/personalize certain
vehicle options to suit your needs.
The message center is also capable of monitoring many vehicle systems
and will alert you to potential vehicle problems and various conditions
with an informational message followed by a long indicator chime.
The message center display is located in the instrument cluster.

Info (information menu)

Press INFO repeatedly to cycle
through the following features:

TRIP A/B
Registers the distance of individual journeys. Press and release INFO
until the A or B trip appears in the display (this represents the trip
mode). Press and hold RESET for two seconds to reset.
Refer to UNITS later in this section to switch the display from Metric to
English.
MYKEY MILES (km) (if programmed)
For more information refer to MyKey™ in the Locks and Security
chapter.
MILES (km) TO E
This displays an estimate of approximately how far you can drive with
the fuel remaining in your tank under normal driving conditions.
Remember to turn the ignition off when refueling to allow this feature to
correctly detect the added fuel.
LOW FUEL LEVEL will display when you have approximately 50 miles
(80 km), to empty. Press RESET to clear this warning message. It will
return at approximately 25 miles (40 km), 10 miles (16 km) and 0 miles
(0 km) miles to empty.
Distance to empty is calculated using a running average fuel economy,
which is based on your recent driving history of 500 miles (800 km).

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

This value is not the same as the average fuel economy display. The
running average fuel economy is re-initialized to a factory default value if
the battery is disconnected.

AVG MPG (L/100km)

Average fuel economy displays your average fuel economy in miles/gallon
or liters/100 km.

If you calculate your average fuel economy by dividing distance traveled
by gallons of fuel used (liters of fuel used by 100 kilometers traveled),
your figure may be different than displayed for the following reasons:
• Your vehicle was not perfectly level during fill-up
• Differences in the automatic shut-off points on the fuel pumps at

service stations

• Variations in top-off procedure from one fill-up to another
• Rounding of the displayed values to the nearest 0.1 gallon (liter)
To determine your average highway fuel economy, do the following:

1. Drive the vehicle at least 5 miles (8 km) with the speed control
system engaged to display a stabilized average.

2. Record the highway fuel economy for future reference.

It is important to press the RESET button (press and hold RESET for
two seconds in order to reset the function) after setting the speed
control to get accurate highway fuel economy readings.

For more information refer to Essentials of good fuel economy in the
Maintenance and Specifications chapter.

MPG (L/km)

This displays instantaneous fuel economy as a bar graph ranging from

↓

poor economy to

↑ excellent economy.

Your vehicle must be moving to calculate instantaneous fuel economy.
When your vehicle is not moving, this function shows

↓, one or no bars

illuminated. Instantaneous fuel economy cannot be reset.

TIMER

Timer displays the trip elapsed drive time.

To operate, do the following:

1. Press and release RESET in order to start the timer.

2. Press and release RESET to pause the timer.

3. Press and hold RESET until the timer resets.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

Blank Screen

The message center display will be blank after cycling through all of the
Info menu items.

System check and vehicle feature customization

Press the SETUP button repeatedly
to cycle the message center through
the following features:

RESET FOR SYSTEM CHECK

When this message appears, press
the RESET button and the message
center will begin to cycle through
the following systems and provide a
status of the item if needed.

1. XXX% OIL LIFE

2. DOORS STATUS

3. TRUNK CLOSED

4. BLIND SPOT SYSTEM (if equipped)

5. CROSS TRAFFIC SYSTEM (if equipped)

6. BRAKE SYSTEM

7. FUEL LEVEL

8. MYKEY DISTANCE (If MyKey™ is programmed)
9. MYKEY(S) PROGRAMMED
10. ADMIN KEYS PROGRAMMED
Note: Some systems show a message only if a condition is present.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

OIL LIFE

This displays the remaining oil life.

An oil change is required whenever indicated by the message center and
according to the recommended maintenance schedule. USE ONLY
RECOMMENDED ENGINE OILS.

To reset the oil monitoring system to 100% after each oil change,
perform the following:

1. Press and release SETUP to display “OIL LIFE XXX% HOLD RESET =
NEW”.

2. Press and hold RESET for two seconds and release to reset the oil life
to 100%.

Note: To change oil life value to another value, proceed to Step 3.

3. Once “OIL LIFE SET TO XXX%” is displayed, release and press the
RESET button to change the Oil Life Start Value. Each release and press
will reduce the value by 10%.

UNITS

Displays the current units English or Metric.

Press RESET to change from English to Metric.

AUTOLAMP (SEC)

This feature keeps your headlights on for up to three minutes after the
ignition is switched off.

Press RESET to select the new Autolamp delay values of 0, 10, 20, 30,
60, 90, 120 or 180 seconds.

AUTOLOCK

This feature automatically locks all vehicle doors when the vehicle is
shifted into any gear, putting the vehicle in motion.

Press RESET to turn autolock on or off.

AUTOUNLOCK

This feature automatically unlocks all vehicle doors when the driver’s
door is opened within 10 minutes of the ignition being turned off.

Press RESET to turn autounlock on or off.

BLIND SPOT (if equipped)

The Blind Spot Information System (BLIS

威) is designed to assist the

driver by monitoring the side areas on both sides of the vehicle.

Press RESET to turn it off or on.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

CROSS TRAFFIC (if equipped)

This system is designed to assist and warn the driver when backing out
of parking spaces.

Press RESET to turn it off or on.

PARK AID (Reverse sensing system–if equipped)

This feature sounds a warning tone to warn the driver of obstacles near
the rear bumper, and functions only when R (Reverse) gear is selected.

Press RESET to turn the rear park assist off.

CREATE MYKEY / MYKEY SETUP/ CLEAR MYKEY

For more information refer to MyKey™ in the Locks and Security
chapter.
LANGUAGE = ENGLISH / SPANISH / FRENCH
Allows you to choose which language the message center will display in.
Selectable languages are English, Spanish, or French.
Waiting four seconds or pressing the RESET button cycles the message
center through each of the language choices.
Press and hold RESET for two seconds to set the language choice.

System warnings
System warnings alert you to possible problems or malfunctions in your
vehicle’s operating systems.
In the event of a multiple warning situation, the message center will
cycle the display to show all warnings by displaying each one for several
seconds.
The message center will display the last selected feature if there are no
more warning messages. This allows you to use the full functionality of
the message center after you acknowledge the warning by pressing the
RESET control and clearing the warning message.
Warning messages that have been reset are divided into three categories:
• They will not disappear until a condition is changed.

• They will reappear on the display 10 minutes from the reset.

• They will not reappear until an ignition off/on cycle has been

completed.

This acts as a reminder that these warning conditions still exist within
the vehicle.
PARK BRAKE ENGAGED — Displayed when the park brake is
engaged. If the warning stays on after the park brake is off, contact your
authorized dealer as soon as possible.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

CHECK BRAKE SYSTEM — Displayed when the brake system needs
servicing. If the warning stays on or continues to come on, contact your
authorized dealer as soon as possible.

DRIVER DOOR AJAR — Displayed when the driver’s door is not
completely closed.

PASSENGER DOOR AJAR — Displayed when the passenger side door
is not completely closed.

REAR LEFT DOOR AJAR — Displayed when the rear left door is not
completely closed.

REAR RIGHT DOOR AJAR — Displayed when the rear right door is
not completely closed.

FUEL LEVEL LOW — Displayed as an early reminder of a low fuel
condition.

CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may
not be properly closed. Refer to Easy Fuel™ “no cap” fuel system in
the Maintenance and Specifications chapter.

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low
and the brake system should be inspected immediately. Refer to Brake
fluid in the Maintenance and Specifications chapter.

CHECK PARK AID (if equipped) — Displayed when the transmission
is in R (Reverse) and the reverse sensing system (park aid) is disabled.
Refer to Reverse sensing system (Park Aid) in this section to enable.

LOW TIRE PRESSURE — Displayed when one or more tires on your
vehicle have low tire pressure. Refer to Inflating your tires in the Tires,
Wheels and Loading chapter.

TIRE PRESSURE MONITOR FAULT — Displayed when the tire
pressure monitoring system is malfunctioning. If the warning stays on or
continues to come on, contact your authorized dealer as soon as
possible.

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure
sensor is malfunctioning, or your spare tire is in use. For more
information on how the system operates under these conditions, refer to
Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and
Loading chapter. If the warning stays on or continues to come on,
contact your authorized dealer as soon as possible.

POWER STEERING ASSIST FAULT (if equipped) — The power
steering system has disabled power steering assist due to a system error,
service is required.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

SERVICE POWER STEERING (if equipped) — The power steering
system has detected a condition that requires service.

SERVICE POWER STEERING NOW (if equipped) — The power
steering system has detected a condition within the power steering
system that requires service immediately.

SERVICE ADVANCETRAC — Displayed when the AdvanceTrac

威

system has detected a condition that requires service.

TRUNK AJAR — Displayed when the trunk is not completely closed.

REMOVE OBJECTS NEAR PASS SEAT — Displayed when objects
are by the passenger seat. After the objects are moved away from the
seat, if the warning stays on or continues to come on, contact your
authorized dealer as soon as possible.

ENGINE OIL CHANGE SOON — Displayed when the engine oil life
remaining is 10% or less. When oil life left is between 10% and 0%, the
XX% OIL LIFE CHANGE SOON message will be displayed.

OIL CHANGE REQUIRED — Displayed when the oil life left reaches
0%.

BLIND SPOT SYSTEM FAULT (if equipped) — Displayed when a
fault with the blind spot information system has occurred. Contact your
authorized dealer as soon as possible.

CROSS TRAFFIC SYSTEM FAULT (if equipped) — Displayed when
a fault with the cross traffic alert system has occurred. Contact your
authorized dealer as soon as possible.

BLIND SPOT NOT AVAILABLE (if equipped) — Displayed when
blind spot information system is not available. See Blind Spot
Information System (BLIS

威) with Cross Traffic Alert in the Driving

chapter.

CROSS TRAFFIC NOT AVAILABLE (if equipped) — Displayed
when cross traffic alert is not available. See Blind Spot Information
System (BLIS

威) with Cross Traffic Alert in the Driving chapter.

SENSOR BLOCKED SEE MANUAL (if equipped) — Displayed when
the blind spot information system/cross traffic alert system sensors are
blocked. See Blind Spot Information System (BLIS

威) with Cross

Traffic Alert in the Driving chapter.

VEHICLE COMING FROM LEFT (if equipped) — Displayed when
the blind spot information system with cross traffic alert (CTA) system is
operating and senses a vehicle. See Blind Spot Information System
(BLIS

威) with Cross Traffic Alert in the Driving chapter.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

VEHICLE COMING FROM RIGHT (if equipped) — Displayed when
the blind spot information system with cross traffic alert (CTA) system is
operating and senses a vehicle. See Blind Spot Information System
(BLIS

威) with Cross Traffic Alert in the Driving chapter.

CHECK AWD (if equipped) — Displayed when a problem exists with
the AWD system. Contact your authorized dealer as soon as possible.

AWD OFF (if equipped) — Displayed when the AWD system has been
automatically disabled to protect itself. This is caused by operating the
vehicle with the compact spare tire installed or if the system is
overheating. The AWD system will resume normal function and clear this
message after driving a short distance with the road tire re-installed or
after the system is allowed to cool.

TO STOP ALARM START VEHICLE — Displayed when the perimeter
alarm system is armed and the vehicle is entered using the key on the
driver’s side door. In order to prevent the perimeter alarm system from
triggering, the ignition must be turned to start or on before the
12 second chime expires. See Perimeter alarm system in the Locks and
security chapter.

INTKEY COULD NOT PROGRAM — Displayed when an attempt is
made to program an invalid key or more than the maximum number of
integrated keys allowed. For more information on integrated key, refer to
the Locks and Security chapter.

MYKEY ACTIVE DRIVE SAFELY — Displayed at startup when
MyKey™ is in use. Refer to MyKey™ in the Locks and Security chapter
for more information.

KEY COULD NOT PROGRAM — Displayed when an attempt is made
to program a spare key using two existing MyKeys. Refer to MyKey™ in
the Locks and Security chapter for more information.

VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey™ is in
use and the admin has enabled the MyKey speed limit and the vehicle
speed is 80 mph (130 km/h). Refer to MyKey™ in the Locks and
Security chapter for more information.

SPEED LIMITED TO 80 MPH — Displayed when starting the vehicle
and MyKey™ is in use and the MyKey speed limit is on. Refer to
MyKey™ in the Locks and Security chapter for more information.

CHECK SPEED DRIVE SAFELY — Displayed when a MyKey™ is in
use and the optional setting is on and the vehicle exceeds a preselected
speed. Refer to MyKey™ in the Locks and Security chapter for more
information.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in use
and the MyKey speed limit is on and the vehicle speed is approaching
80 mph (130 km/h). Refer to MyKey™ in the Locks and Security
chapter for more information.

TOP SPEED MYKEY SETTING — Displayed when a MyKey™ is in
use and the MyKey speed limit is on and the vehicle speed is 80 mph
(130 km/h). Refer to MyKey™ in the Locks and Security chapter for
more information.

BUCKLE UP TO UNMUTE AUDIO — Displayed when a MyKey™ is in
use and Belt-Minder

威 is activated. Refer to MyKey™ in the Locks and

Security chapter for more information.

ADVTRAC ON MYKEY SETTING — Displayed when a MyKey™ is in
use when trying to disable the AdvanceTrac

威 system and the optional

setting is on. Refer to MyKey™ in the Locks and Security chapter for
more information.

Instrument Cluster

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

AUDIO SYSTEMS

AM/FM/single CD MP3 satellite compatible sound system

WARNING: Driving while distracted can result in loss of vehicle
control, accident and injury. Ford strongly recommends that

drivers use extreme caution when using any device or feature that may
take their focus off the road. Your primary responsibility is the safe
operation of the vehicle. We recommend against the use of any
handheld device while driving and that you comply with all applicable
laws.

Accessory delay: Your vehicle is equipped with accessory delay. With
this feature, the radio and other electrical accessories may be used for
up to 10 minutes after the ignition is turned off or until either front door
is opened.
Setting the clock
To set the time, press CLOCK#. The display will read SET TIME. Use the
memory preset numbers (0–9) to enter in the desired time–hours and
minutes and press OK. The clock will then begin from that time.
AM/FM Radio

/ VOL (Power/Volume): Press to turn the radio on/off. Turn the

knob to increase/decrease volume.
If the volume is set above a certain level and the ignition is turned off,
the volume will come back on at a nominal listening level when the
ignition switch is turned back on.

Entertainment Systems

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

AM/FM: Press repeatedly to select AM/FM1/FM2 frequency band.

TUNE: Turn the knob to go up/down the frequency band in individual
increments.

DIRECT: Press DIRECT and then select the desired radio frequency
(i.e. 93.9) using the memory preset numbers (0–9).

SEEK/TRACK: Press

SEEK/TRACK

to access the

previous/next strong radio station.

SCAN: Press for a brief sampling of all strong radio stations.

MEMORY PRESETS (0–9): When tuned to any station, press and hold
a preset button until sound returns and PRESET # SAVED appears in
the display. You can save up to 30 stations, 10 in AM, 10 in FM1 and
FM2.

Saving presets automatically– Autoset allows you to set the strongest
local radio stations without losing your original manually set preset
stations for AM/FM1/FM2.

To activate the autoset feature: Press MENU repeatedly until AUTO
PRESET ON/OFF appears in the display. Use

SEEK/TRACK

toggle AUTO PRESET to ON, and either wait five seconds for the search
to initiate or press OK to immediately initiate the search. If you press
another control within those five seconds, the search will not initiate.
The 10 strongest stations will be filled and the station stored in preset 1
will begin playing.

If there are fewer then 10 strong stations, the system will store the last
one in the remaining presets.

RDS (Radio Data System) Radio

Available only in FM mode. This feature allows you to search
RDS-equipped stations for a certain category of music format: CLASSIC,
COUNTRY, JAZZ/RB, ROCK, etc.

To activate: Press MENU repeatedly until RDS (ON/OFF) appears in the
display. Use

SEEK/TRACK

to toggle RDS ON/OFF. When RDS is

OFF, you will not be able to search for RDS equipped stations or view
the station name or type.

CAT/FOLD (Category/Folder): This feature allows you to select from
various music categories.

To change RDS categories: Press MENU repeatedly until RDS ON/OFF
appears in the display. Use

to toggle RDS to ON. Press CAT.

Entertainment Systems

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

PRESS UP OR DOWN TO CHANGE RDS CATEGORY will appear in the
display. Press

to scroll through all possible categories. When the

desired category appears in the display, press

SEEK/TRACK

find the next station playing that selection or press SCAN for a brief
sampling of all stations playing that category of music.

CD/MP3 Player

CD: Press to enter CD/MP3 mode. If a disc is already loaded into the
system, CD/MP3 play will begin where it ended last. If no CD is loaded,
NO DISC will appear in the display.

LOAD: To load a CD, simply insert the disc, label side up, into the CD
slot.

EJECT: Press EJECT to eject the CD.

Play/Pause: Press to

play/pause a track when playing a
CD.

SEEK/TRACK: Press

SEEK/TRACK

to access the

previous/next track.

CAT (Category) / FOLD (Folder):

In MP3 mode only– Press CAT/FOLD and then press
SEEK/TRACK

to access the previous/next folder.

SCAN: Press for a brief sampling of all tracks on the current disc or
MP3 folder.

DIRECT:

In CD mode– Press DIRECT. The display will read DIRECT TRACK
MODE SELECT TRACK. Enter the desired track number using the
memory preset buttons (0–9). The system will then begin playing that
track.

In MP3 folder mode– Press DIRECT and the memory preset buttons
(0–9) of the desired folder. The system will advance to that specific
folder.

TEXT:

In MP3 mode only– Press TEXT repeatedly to view Album (AL), Folder
(FL), Song (SO) and Artist (AR) in the display, if available.

Entertainment Systems

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

In TEXT MODE: Sometimes the display requires additional text to be
displayed. When the < / > indicator is active, press TEXT and then
press

SEEK/TRACK

to view the additional display text.

COMPRESSION: Press MENU repeatedly until COMPRESSION ON/OFF
appears in the display. Use

SEEK/TRACK

to toggle between

ON/OFF. When COMPRESSION is ON, the system will bring the soft and
loud CD passages together for a more consistent listening level.

SHUFFLE: Press MENU repeatedly until SHUFFLE ON/OFF appears in
the display. Use

SEEK/TRACK

to toggle between ON/OFF. If

you wish to engage shuffle mode right away, press
SEEK/TRACK

to begin random play. Otherwise, random play will

begin when the current track is finished playing. The system will only
shuffle the currently playing disc.

Satellite Radio (if equipped)

Satellite radio is available only with a valid SIRIUS

威 radio

subscription. Check with your authorized dealer for availability.

SIRIUS: Press repeatedly to access satellite radio mode, if equipped.
Press repeatedly to cycle through SAT1, SAT2 and SAT3 modes.

TUNE/OK: Turn the knob to go to the next / previous available SIRIUS

威

satellite station.

DIRECT: Press DIRECT then enter the desired channel (i.e. 002) using
the memory preset buttons (0–9). If you only enter one digit, press OK
and the system will go to that satellite channel. If you enter three digits,
the system will automatically go to that channel, if available. You may
cancel your entry by pressing DIRECT. If an invalid station number is
entered, INVALID CHANNEL will appear in the display and the system
will continue playing the current station.

SEEK/TRACK: Press

SEEK/TRACK

to seek to the

previous/next channel. If a specific category is selected, (Jazz, Rock,
News, etc.), press

SEEK/TRACK

to seek to the previous/next

channel in the selected category. Press and hold

SEEK/TRACK

to fast seek through the previous/next channels.

SCAN: Press SCAN for a brief sampling of all available SIRIUS

威 satellite

channels. If a specific category is selected, (Jazz, Rock, News, etc.) press
SCAN for a brief sampling of all available SIRIUS

威 satellite channels

within the selected category.

Entertainment Systems

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

MEMORY PRESETS (0–9): There
are 30 available presets, 10 each for
SAT1, SAT2 and SAT3. To save
satellite channels in your memory
presets, tune to the desired channel
then press and hold a memory preset number (0–9) until sound returns.

TEXT: Press and release to display the artist and song title. While in
TEXT MODE, press again to scroll through the Artist (AR), Song (SO),
Channel (CH) and Category (CA).

In TEXT MODE: Sometimes the display requires additional text to be
displayed. When the < / > indicator is active, press TEXT and then
press

SEEK/TRACK

to view the additional display text.

CAT (Category) / FOLD (Folder): Press to toggle between turning
the most recently selected satellite radio category on or off. The category
icon (CAT) will illuminate in the display when a specific category is
selected (the icon will not illuminate during CATEGORY ALL). If no
category has ever been selected, NO CATEGORY SELECTED will display.

Note: Separate categories can be set for SAT1, SAT2 or SAT3.
Refer to Satellite radio menu for further information on selecting a
satellite radio category.

SATELLITE RADIO MENU: Press MENU when satellite radio mode is
active to access. Press OK to enter into the satellite radio menu.
Press

to cycle through the following options:

• CATEGORY MENU- Press OK to enter category mode.

Press

to scroll through the list of available SIRIUS

威 channel

Categories (Pop, Rock, News, etc.) Press OK when the desired
category appears in the display. After a category is selected,
press

to search for that specific category of channels only

(i.e. ROCK). You may also select CATEGORY ALL to seek all available
SIRIUS

威 categories and channels. Press OK to close and return to the

main menu.

• SONG SEEK MENU- Press OK to enter song seek menu.

Press

to scroll through the following options:

a. SAVE THIS SONG: Press OK to save the currently playing song’s
title in the system’s memory. (If you try to save something other than
a song, CANT SAVE will appear in the display.) When the chosen song
is playing on any satellite radio channel, the system will alert you with
an audible prompt. Press OK while SONG ALERT is in the display and

Entertainment Systems

2011 Milan (mln)
Owners Guide, 1st Printing
USA (fus)

Mercury Milan (2011 year). Manual - part 2