Ford Focus Electric (2018 year). Manual - part 7

 

  Index      Ford     Ford Focus Electric - service manual 2018 year in english

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  5  6  7  8   ..

 

 

Ford Focus Electric (2018 year). Manual - part 7

 

 

Pregnant women should always wear their
seatbelt.  The lap belt portion of a
combination lap and shoulder belt should
be positioned low across the hips below
the belly and worn as tight as comfort
allows.  The shoulder belt should be
positioned to cross the middle of the
shoulder and the center of the chest.

Seatbelt Locking Modes

WARNINGS

After a crash, have a qualified
technician check all the seatbelts to
make sure the seatbelts including

the automatic locking retractor feature for
child restraints operate properly. We
recommend replacing any system that has
damage or does not operate properly.
Failure to do so can result in personal injury
or death in the event of a sudden stop or
another crash.

You must replace the seatbelt if the
automatic locking retractor or any
other seatbelt function is not

operating correctly. Failure to replace the
seatbelt and retractor assembly could
increase the risk of injury in a crash.

All safety restraints in your vehicle are
combination lap and shoulder belts.  The
driver seatbelt has the first type of locking
mode.  The front outermost passenger and
rear seat seatbelts have both types of
locking modes described as follows:

Vehicle Sensitive Mode

This is the normal retractor mode which
allows free shoulder belt length
adjustment to your movements and
locking in response to vehicle movement.
For example, if you brake suddenly or turn
a corner sharply, or your vehicle receives
an impact of approximately 5 mph
(8 km/h) or more, the combination
seatbelts lock to help reduce forward
movement of the driver and passengers.

In addition, the retractor is designed to lock
if you pull the webbing out too quickly. If
the seatbelt retractor locks, slowly lower
the height adjuster to allow the seatbelt
to retract. If the retractor does not unlock,
pull the seatbelt out slowly then feed a
small length of webbing back toward the
stowed position. For rear seatbelts, recline
the rear seat backrest or push the seat
backrest cushion away from the seatbelt.
Feed a small length of webbing back
toward the stowed position.

Automatic Locking Mode

In this mode, the shoulder belt
automatically pre-locks. The seatbelt still
retracts to remove any slack in the
shoulder belt. The automatic locking mode
is not available on the driver seatbelt.

Using Automatic Locking Mode

You should use automatic locking mode
when a child safety seat, except a booster,
is on the front passenger seat or rear seat.
Children 12 years old and under should be
correctly restrained in a rear seating
position whenever possible.  See Child
Safety (page 15).

E142591

1.

Buckle the combination lap and
shoulder belt.

2. Grasp the shoulder portion and pull

downward until you pull the entire
seatbelt out.

3. Let the seatbelt retract.

Note: As the seatbelt retracts, you will hear
a clicking sound. This indicates the seatbelt
is now in the automatic locking mode.

Disengaging Automatic Locking Mode

Unbuckle the combination lap and
shoulder belt and allow it to retract
completely to disengage the automatic
locking mode and return the seatbelt to
the vehicle sensitive mode.

SEATBELT HEIGHT
ADJUSTMENT

WARNING

Position the seatbelt height adjuster
so that the seatbelt rests across the
middle of your shoulder. Failure to

adjust the seatbelt correctly could reduce
its effectiveness and increase the risk of
injury in a crash.

Adjust the height of the shoulder belt so
the belt rests across the middle of your
shoulder.

E183582

To adjust the shoulder belt height:

1.

Press the button and slide the height
adjuster up or down.

2. Release the button and pull down on

the height adjuster to make sure it is
locked in place.

SEATBELT WARNING LAMP
AND INDICATOR CHIME

E71880

This lamp illuminates and an
audible warning will sound if the
driver seatbelt has not been

fastened when the vehicle's ignition is
turned on.

Conditions of operation

Then

If

The seatbelt warning light illuminates and

the warning chime sounds for a few

seconds.

The driver seatbelt is not buckled before

the ignition switch is turned to the on posi-

tion...

The seatbelt warning light and warning

chime turn off.

The driver seatbelt is buckled while the

indicator light is illuminated and the

warning chime is sounding...

The seatbelt warning light and indicator

chime remain off.

The driver seatbelt is buckled before the

ignition switch is turned to the on position...

SEATBELT REMINDER

Belt-Minder™

This feature supplements the seatbelt
warning function by providing additional
reminders that intermittently sound a tone
and illuminate the seatbelt warning light
when you are in the driver seat or you have
a front seat passenger and a seatbelt is
unbuckled.

The system uses information from the
front passenger sensing system to
determine if a front seat passenger is
present and therefore potentially in need
of a warning. To avoid activating the
Belt-Minder feature for objects you place
in the front passenger seat, only the front
seat passengers receive warnings as
determined by the front passenger sensing
system.

If the Belt-Minder warnings expire
(warnings for about five minutes) for one
passenger (driver or front passenger), the
other passenger can still cause the
Belt-Minder feature to turn on.

Then

If

The Belt-Minder feature will not activate.

You and the front seat passenger buckle

your seatbelts before you switch the igni-

tion on or less than 1-2 minutes elapse after

you switch the ignition on...

The Belt-Minder feature activates, the

seatbelt warning light illuminates and a

warning tone sounds for 6 seconds every

25 seconds, repeating for about 5 minutes

or until you and the front seat passenger

buckle your seatbelts.

You or the front seat passenger do not

buckle your seatbelts before your vehicle

reaches at least 6 mph (9.7 km/h) and 1-2

minutes elapse after you switch the ignition

on...

The Belt-Minder feature activates, the

seatbelt warning light illuminates and a

warning tone sounds for 6 seconds every

25 seconds, repeating for about 5 minutes

or until you and the front seat passenger

buckle your seatbelts.

The seatbelt for the driver or front

passenger is unbuckled for about 1 minute

while the vehicle is traveling at least 6 mph

(9.7 km/h) and more than 1-2 minutes

elapse after you switch the ignition on...

Deactivating and Activating the
Belt-Minder Feature

WARNING

While the system allows you to
deactivate it, this system is designed
to improve your chances of being

safely belted and surviving an accident.
We recommend you leave the system
activated for yourself and others who may
use the vehicle.

Note: The driver and front passenger
warnings switch on and off independently.
When you perform this procedure for one
seating position, do not buckle the other
position as this will terminate the process.

Note: If you are using MyKey™, you cannot
disable the Belt-Minder. Also, if you have
previously disabled the Belt-Minder, it will
be re-enabled during the use of MyKey™.
See MyKey™ (page 48).

Read Steps 1 - 4 thoroughly before
proceeding with the programming
procedure.

Before following the procedure, make sure
that:

The parking brake is set.

The transmission is in park (P).

The ignition is off.

The driver and front passenger
seatbelts are unbuckled.

1.

Switch the ignition on.  Do not start the
vehicle (Ready to Drive light must not
be lit).

2. Wait until the seatbelt warning light

turns off (about one minute). Once you
start Step 3, you must complete the
procedure within 60 seconds.

3. For the seating position you are

switching off, buckle then unbuckle the
seatbelt four times at a moderate
speed, ending in the unbuckled state.
After Step 3, the seatbelt warning light
turns on.

 

 

 

 

 

 

 

Content   ..  5  6  7  8   ..