Chrysler New Yorker. Manual - part 598

TEST TC-60A

CONTINUED - REPAIRING - BAROMETRIC PRESSURE OUT OF RANGE

2.7L

FIG. 1

3.5L

FIG. 2

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

228

TEST TC-60A

CONTINUED - REPAIRING - BAROMETRIC PRESSURE OUT OF RANGE

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST TC-60A 

CONTINUED FROM 

THE PREVIOUS 

TURN IGNITION OFF. 

PAGE.

DISCONNECT THE

WITH AN OHMMETER,

POWERTRAIN CONTROL

MEASURE THE 5-VOLT 

IS THE RESISTANCE 

YES

REPAIR THE 5-VOLT 

MODULE HARNESS

SUPPLY CIRCUIT TO 

BELOW 5.0 OHMS?

SUPPLY CIRCUIT FOR

CONNECTOR.** GROUND.

A SHORT TO 

SEE GENERAL INFO 4.1

FIG. 1 OR 2

GROUND.* 

NO 

USING AN OHMMETER,

REPAIR THE OPEN 

MEASURE RESISTANCE 

IS THE RESISTANCE 

NO 

5-VOLT SUPPLY 

OF THE 5-VOLT 

BELOW 5.0 OHMS?

CIRCUIT BETWEEN

SUPPLY CIRCUIT. 

MAP SENSOR AND PCM

FIG. 1 OR 2

CONNECTORS.* 

YES

REPLACE THE

POWERTRAIN CONTROL

MODULE.* 

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

229

TEST TC-61A

REPAIRING - INJECTOR #4 CONTROL CIRCUIT

Perform TEST TC-21A Before Proceeding

FIG. 1

FIG. 2

FIG. 3

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

230

TEST TC-61A

REPAIRING - INJECTOR #4 CONTROL CIRCUIT

Perform TEST TC-21A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: IT MAY BE 

DISCONNECT INJECTOR 

START TEST 

NECESSARY TO 

REFER TO SERVICE

#4 HARNESS

TC-61A.

REMOVE THE INTAKE 

MANUAL FOR

CONNECTOR.** 

PLENUM IN THE

INSTRUCTIONS.

SEE GENERAL INFO 4.1

FOLLOWING STEPS. 

USING A VOLTMETER, 

USING THE DRB, MEASURE THE ASD

DOES 

THE VOLTAGE

NO 

PERFORM TEST 

ACTUATE THE ASD

RELAY OUTPUT 

CYCLE FROM 0 TO 12 

TC-61B.

RELAY. CIRCUIT. VOLTS? 

FIG. 1

YES

USING AN OHMMETER,

MEASURE THE

IS 

THE RESISTANCE NO REPLACE THE FUEL 

RESISTANCE ACROSS 

BETWEEN 10.0 AND

INJECTOR.* 

THE INJECTOR.

16.0 OHMS?

YES

DISCONNNECT THE

RECONNECT THE

POWERTRAIN CONTROL

INJECTOR HARNESS

MODULE HARNESS

CONNECTOR. CONNECTORS.**

SEE GENERAL INFO 4.1

USING A FUSED

USING A 12 VOLT 

JUMPER, JUMPER B+ TO 

TEST LIGHT, PROBE

DID THE TEST LIGHT

YES

REPLACE THE

THE ASD RELAY OUTPUT 

THE INJECTOR #4 

ILLUMINATE?

POWERTRAIN CONTROL

CKT AT THE PCM

CIRCUIT TO GROUND.

MODULE.* 

HARNESS CONN. FIG. 2

FIG. 2

NO 

USING AN OHMMETER,

REPAIR THE SHORT

DISCONNECT THE

MEASURE THE

IS THE RESISTANCE 

NO 

TO GROUND IN THE

INJECTOR HARNESS

INJECTOR #4 DRIVER 

BELOW 5.0 OHMS?

INJECTOR #4 DRIVER 

CONNECTOR.** CIRCUIT TO 

GROUND.

CIRCUIT.*

FIG. 1

YES

DRIVER CIRCUIT

USING AN OHMMETER,

FROM THE INJECTOR 

IS THE RESISTANCE 

NO 

REPAIR THE OPEN 

MEASURE THE

CONNECTOR TO THE

BELOW 5.0 OHMS?

INJECTOR #4 DRIVER 

INJECTOR #4 ...

PCM CONN.

CIRCUIT.*

FIG. 3

YES

CONTINUE TEST 

TC-61A ON THE

NEXT PAGE 

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

231