|
|
|
•
Speed Buzzer
•
Trip B/Data
•
Set Time
•
Set Date
•
Autoclose
•
Units
•
Language
•
Buzzer Volume
•
Service
•
Daylights (D.R.L.) – If Equipped
•
Exit Menu
Selecting An Option Of The Main Menu Without
Submenu
1. Briefly push the
SET/BACK
button to select the main
menu option to set.
2. Push the
up
or
down
arrow button (by a single push)
to select the new setting.
3. Briefly push the
SET/BACK
button to store the new
setting and go back to the main menu option previ-
ously selected.
Selecting An Option Of The Main Menu With Sub-
menu
1. Briefly push the
SET/BACK
button to display the
first submenu option.
2. Push the
up
or
down
arrow button (by a single push)
to scroll through all the submenu options.
3. Briefly push the
SET/BACK
button to select the
displayed submenu option and to open the relevant
setup menu.
4. Push the
up
or
down
arrow button (by a single push)
to select the new setting for this submenu option.
5. Briefly push the
SET/BACK
button to store the new
setting and go back to the previously selected sub-
menu option.
6. Push and hold the
SET/BACK
button to return to the
main menu (short hold) or the main screen (longer
hold).
4
GETTING TO KNOW YOUR INSTRUMENT PANEL
67
Speed Buzzer (Speed Limit)
With this function, it is possible to set the vehicle speed
limit (MPH or km/h) to immediately alert the driver
when the set limit is exceeded.
To set the speed limit, proceed as follows:
1. Briefly push the
SET/BACK
button. The display will
show the message (Speed Buzzer).
2. Push and release the
up
or
down
arrow button to
select speed limit activation (On) or deactivation
(Off).
3. When the function is activated (On), briefly push the
SET/BACK
button to display the previously set
speed. Pushing the
up
or
down
arrow buttons selects
the speed limit. Push
SET/BACK
to confirm selec-
tion.
NOTE:
The setting can be increased or decreased by 5
MPH or km/h each time the
up
or
down
arrow button
is pushed for speed settings above 20 MPH (32 km/h).
To increase or decrease the set speed rapidly, push and
hold the
up
or
down
arrow button. Save the setting by
briefly pushing the button when you approach the
required setting.
Briefly push the
SET/BACK
button to go back to the
menu screen, or push and hold the
SET/BACK
button
(approximately one second) to go back to the main
screen without storing the settings.
To cancel the setting, proceed as follows:
1. Briefly push the
SET/BACK
button. “On” will dis-
play.
2. Push and release the
down
button. “Off” will dis-
play.
3. Briefly push the
SET/BACK
button to go back to the
menu screen, or push and hold the
SET/BACK
button (approximately one second) to go back to the
main screen without storing the settings.
Trip B Activation
Through this option, it is possible to activate (On) or
deactivate (Off) the Trip B (partial trip) display.
For further information, see “Trip Computer.”
For activation/deactivation, proceed as follows:
1. Briefly push the
SET/BACK
button. “On” or “Off”
will display in the instrument cluster display (ac-
cording to previous setting).
68
GETTING TO KNOW YOUR INSTRUMENT PANEL
2. Push and release the
up
or
down
arrow button to
select the setting and once selected a beep will occur
to signal the setting is saved.
3. Briefly push the
SET/BACK
button to go back to the
menu screen, or push and hold the
SET/BACK
button (approximately one second) to go back to the
main screen without storing the settings.
Set Time
This function may be used to set the clock through two
submenu items: “Time” and “Mode.”
Proceed as follows:
1. Briefly push the
SET/BACK
button. The display will
show the two submenu items “Time” and “Mode.”
2. Push and release the
up
or
down
arrow button to
navigate the two submenu items.
3. Select the required option and then push the
SET/
BACK
button.
4. When accessing the “Time” submenu item, briefly
push the
SET/BACK
button and “hours” will flash
on the display.
5. Push and release the
up
or
down
arrow button for
setting.
6. Briefly push the
SET/BACK
button and “minutes”
will flash on the display.
7. Push and release the
up
or
down
arrow button for
setting.
NOTE:
•
The setting will increase or decrease by one unit
each time the
up
or
down
arrow button is pushed.
Push and hold the button to increase/decrease the
setting rapidly. Save the setting by briefly pushing
the button when you approach the required setting.
•
Briefly push the
SET/BACK
button to return to the
“Time” sub-function.
•
When accessing the “Mode” submenu, briefly push
the
SET/BACK
button. The previously set display
format will flash on the display.
•
Push and release the
up
or
down
arrow button to
select “24h” or “12h.”
When you have selected the required settings, briefly
push the
SET/BACK
button to go back to the Time,
Mode submenu screen, or push and hold the
SET/
4
GETTING TO KNOW YOUR INSTRUMENT PANEL
69
BACK
button (approximately one second) to go back to
the main screen without storing the settings.
Set Date
This function may be used to set the date (day - month
- year).
To change the date, proceed as follows:
1. Briefly push the
SET/BACK
button and “year” will
flash on the display.
2. Push and release the
up
or
down
arrow button for
setting.
3. Briefly push the
SET/BACK
button and “month”
will flash on the display.
4. Push and release the
up
or
down
arrow button for
setting.
5. Briefly push the
SET/BACK
button and “day” will
flash on the display.
6. Push and release the
up
or
down
button for setting.
NOTE:
The setting will increase or decrease by one
unit each time the
up
or
down
arrow button is pushed.
Push
and
hold
the
up
or
down
arrow
button
to
increase/decrease the setting rapidly. Save the setting
by briefly pushing the button when you approach the
required setting.
Briefly push the
SET/BACK
button to go back to the
menu screen, or push and hold the
SET/BACK
button
(approximately one second) to go back to the main
screen without storing the settings.
Autoclose
With this function active, the doors will automatically
lock at when the vehicle’s speed exceeds 12 MPH
(20 km/h).
To change the setting, proceed as follows:
1. Briefly push the
SET/BACK
button “On” or “Off”
will flash on the display (according to the previous
setting).
2. Push and release the
up
or
down
arrow button for
setting.
70
GETTING TO KNOW YOUR INSTRUMENT PANEL
|
|
|