Acura TSX / Honda Accord CL. Manual - part 570

Fig. 71: Evaporative Emission (EVAP) System Wiring Diagram (11 Of 11)

HOW TO SET READINESS CODES

Malfunction Indicator Lamp (MIL) Indication (In relation to Readiness Codes)

The vehicle has certain "readiness codes" that are part of the on-board diagnostics for the emissions systems. If
the vehicle's battery has been disconnected or gone dead, if the DTCs have been cleared, or if the ECM/PCM

2004 Acura TSX

2004 ENGINE PERFORMANCE Fuel & Emissions Systems - TSX

has been reset, these readiness codes are reset. In some states, part of the emissions testing is to make sure these
codes are set to complete. If all of them are not set to complete, the vehicle may fail the emission test, or the test
cannot be finished.

To check if the readiness codes are set to complete, turn the ignition switch ON (II), but do not start the engine.
The MIL will come on for 15-20 seconds. If it then goes off, the readiness codes are complete. If it flashes five
times, one or more readiness codes are not set to complete. To set readiness codes from incomplete to complete,
do the procedure for the appropriate code.

To check the status of a specific DTC system, check the OBD status in the DTC MENU with the HDS (see
OBD Status ). This screen displays the code, the current data list of the enable criteria, and the status of the
readiness testing.

Catalytic Converter Monitor & Readiness Code

ENABLE CRITERIA

ECT at 158° F (70° C) or higher.

Intake air temperature (IAT) at 20° F (-7° C) or higher.

Vehicle speed sensor (VSS) reads more than 25 mph (40 km/h).

PROCEDURE

1. Connect the HDS to the vehicle's data link connector (DLC), and bring up the READINESS CODEs

screen for Catalyst in the DTCs MENU.

2. Start the engine.

3. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. After about 5

miles (8 km), the readiness code should switch to completed.

4. If the readiness code is still not set to complete, check for a temporary DTC with the HDS. If there is no

DTC, one or more of the enable criteria were probably not met; repeat the procedure.

EVAPORATIVE EMISSIONS (EVAP) CONTROL SYSTEM MONITOR & READINESS CODE

NOTE:

Do not turn the ignition switch off during the procedure.

All readiness codes are cleared when the battery is disconnected or when
the ECM/PCM is cleared with the HDS.

Low ambient temperatures or excessive stop-and-go traffic may increase
the drive time needed to switch the readiness code from incomplete to
complete.

The readiness code will not switch to complete until all the enable criteria
are met.

If a fault in the secondary HO2S system caused the MIL to come on, the
readiness code cannot be set to complete until you correct the fault.

2004 Acura TSX

2004 ENGINE PERFORMANCE Fuel & Emissions Systems - TSX

ENABLE CRITERIA

Battery voltage is higher than 10.5 V.

Engine at idle.

ECT sensor between 176°F (80°C) and 212° F (100° C).

MAP sensor less than 46.6 kPa (350 mm Hg, 14 in. Hg).

Vehicle speed 0 mph (0 km/h).

IAT sensor between 32° F (0° C) and 212° F (100° C).

PROCEDURE

1. Connect the HDS to the vehicle's data link connector (DLC).

2. Start the engine.

3. Select EVAP TEST in the INSPECTION MENU with the HDS, then select the FUNCTION TEST in the

EVAP TEST MENU.

If the functions are normal, readiness is complete.

If the functions are not normal, go to the next step.

4. If the readiness code is still not set to complete, check for a temporary DTC. If there is no DTC, one or

more of the enable criteria were probably not met; repeat the procedure.

AIR FUEL RATIO (A/F) SENSOR MONITOR & READINESS CODE

ENABLE CRITERIA

ECT at 140° F (60° C) or higher.

PROCEDURE

1. Start the engine.

2. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. During the drive,

decelerate (with the throttle fully closed) for 5 seconds. After about 3.5 miles (5.6 km), the readiness code
should switch from incomplete to complete.

3. Check the readiness codes screen for the Air Fuel Ratio (A/F) Sensor in the DTCs MENU with the HDS.

If the screen shows complete, readiness is complete.

If the screen shows not complete, go to the next step.

NOTE:

All readiness codes are cleared when the battery is disconnected or when the
ECM/PCM is cleared with the HDS.

NOTE:

Do not turn the ignition switch off during the procedure.

All readiness codes are cleared when the battery is disconnected or when
the ECM/PCM is cleared with the HDS.

2004 Acura TSX

2004 ENGINE PERFORMANCE Fuel & Emissions Systems - TSX

4. Check for a temporary DTC. If there is no DTC, the enable criteria was probably not met. Select the

DATA LIST Menu. Check the ECT in the ALL DATA LIST with the HDS. If the ECT is lower than
140° F (60° C), run the engine until it is higher than 140° F (60° C), then repeat the procedure.

AIR FUEL RATIO (A/F) SENSOR HEATER MONITOR READINESS CODE

PROCEDURE

1. Start the engine, and let it idle for 1 minute. The readiness code should switch from incomplete to

complete.

2. If the readiness code is still not set to complete, check for a temporary DTC. If there is no DTC, repeat

the procedure.

MISFIRE MONITOR & READINESS CODE

This readiness code is always set to available because misfiring is continuously monitored.

Monitoring pauses, and the misfire counter resets, if the vehicle is driven over a rough road.

Monitoring also pauses, and the misfire counter holds at its current value, if the throttle position changes
more than a predetermined value, or if driving conditions fall outside the range of any related enable
criteria.

FUEL SYSTEM MONITOR & READINESS CODE

This readiness code is always set to available because the fuel system is continuously monitored during
closed loop operation.

Monitoring pauses when the catalytic converter, EVAP control system, and A/F sensor monitors are
active.

Monitoring also pauses when any related enable criteria are not being met. Monitoring resumes when the
enable criteria is again being met.

COMPREHENSIVE COMPONENT MONITOR & READINESS CODE

This readiness code is always set to available because the comprehensive component monitor is continuously
running whenever the engine is cranking or running.

NOTE:

All readiness codes are cleared when the battery is disconnected or when the
ECM/PCM is cleared with the HDS.

2004 Acura TSX

2004 ENGINE PERFORMANCE Fuel & Emissions Systems - TSX

Content .. 568 569 570 571 ..