Kia Sedona (2008 year). Manual - part 243

Fig. 102: Output Voltage Graph 
Courtesy of KIA MOTORS AMERICA, INC. 

MONITOR SCAN TOOL DATA 

1. Connect scan tool to Data Link Connector (DLC).  

2. Engine "ON"  

3. Monitor the "DR. DIRECTION POTENTIO." parameter on the scan tool while operating mode switch. 

Fig. 103: Diagnosis Function Screen Display - Direction Potentiometer 
Courtesy of KIA MOTORS AMERICA, INC. 

4. Are the DTC B1249 present and is parameter of "DR. DIRECTION POTENTIO." fixed? 

Parameter of "DR. DIRECTION POTENTIO." will be fixed at 100% (or any value above 90%), or 0% 
(or any value below 10%), if there is any fault in Driver Direction potentiometer. 

YES  

Go to TERMINAL AND CONNECTOR INSPECTION procedure.

 

2008 Kia Sedona EX 

2008 HVAC Blower & A/C Controls (Automatic) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 3:56:08 PM

Page 94 

© 2006 Mitchell Repair Information Company, LLC. 

NO  

Fault is intermittent caused by poor contact in the sensor's and/or A/C controller's connector or was 
repaired and A/C controller memory was not cleared. Thoroughly check connectors for looseness, poor 
connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary 
and then go to "VERIFICATION OF VEHICLE REPAIR" procedure. 

TERMINAL AND CONNECTOR INSPECTION 

1. Many malfunctions in the electrical system are caused by poor harness and terminals. 

Faults can also be caused by interference from other electrical systems, and mechanical or chemical 
damage. 

2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, 

deterioration, or damage.  

3. Has a problem been found? 

YES  

Repair as necessary and go to "VERIFICATION OF VEHICLE REPAIR" procedure. 

NO  

Go to "SIGNAL CIRCUIT INSPECTION" procedure. 

SIGNAL CIRCUIT INSPECTION 

1. Check for open in harness. 

1. Ignition "OFF"  

2. Disconnect Driver mode Actuator.  

3. Measure resistance between terminal "6" of Driver Direction potentiometer and terminal "6" of A/C 

control unit. 

Specification: Approx. 0 ohms 

 

2008 Kia Sedona EX 

2008 HVAC Blower & A/C Controls (Automatic) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 3:56:08 PM

Page 95 

© 2006 Mitchell Repair Information Company, LLC. 

Fig. 104: Checking Resistance Between Terminal "6" Of Driver Direction Potentiometer And 
Terminal "6" Of A/C Control Unit 
Courtesy of KIA MOTORS AMERICA, INC. 

4. Is the measured resistance within specifications? 

YES  

Go to step 2. 

NO  

Check for open in signal harness. Repair as necessary and go to "VERIFICATION OF 
VEHICLE REPAIR" procedure. 

2. Check for short to ground in harness. 

1. Ignition "OFF"  

2. Disconnect Driver mode Actuator.  

3. Measure resistance between terminal "6" of Driver Direction potentiometer and chassis ground. 

Specification: Approx. infinity ohms 

 

2008 Kia Sedona EX 

2008 HVAC Blower & A/C Controls (Automatic) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 3:56:08 PM

Page 96 

© 2006 Mitchell Repair Information Company, LLC. 

Fig. 105: Checking Resistance Between Terminal "6" Of Driver Direction Potentiometer And 
Chassis Ground 
Courtesy of KIA MOTORS AMERICA, INC. 

4. Is the measured resistance within specifications? 

YES  

Go to "POWER CIRCUIT INSPECTION" procedure. 

NO  

Check for short to ground in signal harness. Repair as necessary and go to "VERIFICATION OF 
VEHICLE REPAIR" procedure. 

POWER SUPPLY CIRCUIT INSPECTION 

1. Check for short or open in harness. 

1. Ignition "ON"  

2. Connect Driver Direction potentiometer.  

3. Measure voltage between terminal "7" of Driver Direction potentiometer and chassis ground. 

Specification: Approx. 5V 

Fig. 106: Checking Voltage Between Terminal "7" Of Driver Direction Potentiometer And 
Chassis Ground 
Courtesy of KIA MOTORS AMERICA, INC. 

4. Is the measured voltage within specifications? 

YES  

Go to "COMPONENT INSPECTION" procedure. 

NO  

 

2008 Kia Sedona EX 

2008 HVAC Blower & A/C Controls (Automatic) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 3:56:08 PM

Page 97 

© 2006 Mitchell Repair Information Company, LLC.