Vauxhall New Zafira (2016 year). Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

226

Vehicle care

4. Replace and insert new bulb into

Side turn signal lights

socket.

To replace bulb, remove lamp

5. Insert the bulb socket into the

housing:

reflector and turn clockwise.

6. Install the cover.

Rear fog light

The bulbs are accessible from

beneath the vehicle.

2. Remove the bulb from the socket

by turning anticlockwise.

3. Replace and insert new bulb into

the socket by turning clockwise.

1. Slide lamp to its left side and

4. Insert the bulb socket into the

remove with its right end.

reflector, turn clockwise and

engage.

Bulb check

Switch on the ignition, operate and

1. Turn the bulb socket

check all lights.

anticlockwise and remove it from

the reflector.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

227

4. Insert bulb holder and turn

clockwise.

5. Insert left end of the lamp, slide to

the left and insert right end.

Number plate light

2. Turn bulb holder anticlockwise

2. Remove the bulb from the socket

and remove from housing.

by pulling.

3. Replace the bulb and insert it into

the socket.

4. Push the cover into the housing.

Interior lights

1. Insert screwdriver in recess of the

cover, press to the side and

Courtesy lights, reading lights

release spring. Remove cover.

Have bulbs replaced by a workshop.

Load compartment light

Have bulbs replaced by a workshop.

3. Pull bulb from bulb holder and

replace it.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

228

Vehicle care

Instrument panel

Electrical system

illumination

Fuses

Have bulbs replaced by a workshop.

Data on the replacement fuse must

match the data on the defective fuse.

There are three fuse boxes in the

vehicle:

● in the front left of the engine

compartment

● in left-hand drive vehicles, in the

interior behind the storage

compartment, or, in right-hand

There are different kinds of fuses in

drive vehicles, behind the

the vehicle.

glovebox

● behind a cover on the left side of

the load compartment

Before replacing a fuse, turn off the

respective switch and the ignition.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

229

Depending on the type of fuse, a

Engine compartment fuse

blown fuse can be recognized by its

box

melted wire. Do not replace the fuse

until the cause of the fault has been

remedied.

Some functions are protected by

several fuses.

Fuses may also be inserted without

existence of a function.

Fuse extractor

A fuse extractor may be located in the

Place the fuse extractor on the

fuse box in the engine compartment.

various types of fuse from the top or

side, and withdraw fuse.

The fuse box is in the front left of the

engine compartment.

Disengage the cover and fold it

upwards until it stops. Remove the

cover vertically upwards.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

230

Vehicle care

No. Circuit

Engine control module

Starter

Lambda sensor

Transmission control module

Fuel injection/Ignition system

Heated rear window

Fuel injection/Ignition system

Front power windows

Rear power windows

Exterior mirror heating/Anti-

Rear electrical centre

theft alarm system

Left high beam (Halogen)

Fan control/Engine control

module/Transmission control

module

Right headlight (LED)

Lambda sensor/Engine cooling

Left headlight (LED)

Rear window sensor

Front fog lights

Battery sensor

Diesel fuel heating

Tailgate release

Stop-start system

Adaptive forward lighting/Auto-

Electric parking brake

matic light control

ABS

Adaptive cruise control

Rear window wiper

Airbag

Engine control module

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

231

No. Circuit

Instrument panel fuse box

Adaptive forward lighting/Auto-

Fuel pump

matic light control

Headlamp levelling/Adaptive

Exhaust gas recirculation

forward lighting

Exterior mirror/Rain sensor

Air shutter

Climate control

Auxiliary heater/Diesel engine

Canister vent solenoid

Transmission control module/

Engine control module

Vacuum pump

Vacuum pump/Instrument

Central control module

panel cluster/Heating ventila-

Windscreen washer/Rear

tion/Air conditioning system

In left-hand drive vehicles, the fuse

window washer system

box is behind the storage

After having changed defective fuses,

Right high beam (Halogen)

close the fuse box cover and press

compartment in the instrument panel.

until it engages.

Open the compartment and push it to

Radiator fan

the left to unlock. Fold the

If the fuse box cover is not closed

Windscreen wiper

compartment down and remove it.

correctly, malfunctions may occur.

Windscreen wiper

Radiator fan

Horn

Radiator fan

-------------------------------------------------------------------------------------------------------------------------------------------------------------

232

Vehicle care

No. Circuit

Cruise control/Speed limiter/

Airbag

Adaptive cruise control/Steering

Power outlet

wheel controls

Air conditioning system

Exterior lights/Body control

module

Logistics

Exterior lights/Body control

Body control module

module

Body control module

Infotainment system

Instrument panel cluster/Anti-

Infotainment system/Instrument

In right-hand drive vehicles, the fuse

theft alarm system

box is located behind a cover in the

Power outlet/Cigarette lighter

Ignition sensor

glovebox. Open the glovebox, then

open the cover and fold it down.

Power outlet

Body control module

Left low beam/Body control

Body control module

module

Right low beam/Body control

module/Airbag module

Door locks/Body control module

Load compartment fuse box

Interior fan

The fuse box is on the left side of the

load compartment behind a cover.

Diagnostic connector

-------------------------------------------------------------------------------------------------------------------------------------------------------------

234

Vehicle care

No. Circuit

Vehicle tools

Interior mirror/Rear view

Tools

camera

Active damping system/Lane

Power outlet

departure warning

Steering wheel heating

Sunblind

Heated front seats

Selective catalytic reduction

system

Some tools, the towing eye and (only

on vehicles with spare wheel) the

vehicle jacking equipment are placed

in the rear storage in the load

compartment floor.

Open the cover in front of the tailgate.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

235

Wheels and tyres

Tyre designations

Directional tyres

E.g. 215/60 R 16 95 H

Fit directional tyres such that they roll

Tyre condition, wheel condition

215 : tyre width, mm

in the direction of travel. The rolling

: cross-section ratio (tyre height

direction is indicated by a symbol

Drive over edges slowly and at right

(e.g. an arrow) on the sidewall.

to tyre width), %

angles if possible. Driving over sharp

: belt type: Radial

edges can cause tyre and wheel

RF : type: RunFlat

Tyre pressure

damage. Do not trap tyres on the kerb

: wheel diameter, inches

when parking.

Check the pressure of cold tyres at

: load index e.g. 95 is equivalent

least every 14 days and before any

Regularly check the wheels for

to 690 kg

long journey. Do not forget the spare

damage. Seek the assistance of a

: speed code letter

wheel. This also applies to vehicles

workshop in the event of damage or

Speed code letter:

with tyre pressure monitoring system.

unusual wear.

Q : up to 100 mph

Unscrew the valve cap.

S : up to 112 mph

Winter tyres

: up to 118 mph

Winter tyres improve driving safety at

H : up to 130 mph

temperatures below 7 °C and should

V : up to 150 mph

therefore be fitted on all wheels.

W : up to 168 mph

All tyre sizes are permitted as winter

Choose a tyre appropriate for the

tyres 3 272.

maximum speed of your vehicle.

In accordance with country-specific

The maximum speed is achievable at

regulations, affix the speed sticker in

kerb weight with driver (75 kg) plus

the driver's field of view.

125 kg payload. Optional equipment

could reduce the maximum speed of

the vehicle.

Performance 3 268.

Tyre pressure 3 272.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

236

Vehicle care

The tyre pressure information label

For the tyres approved for your

off ignition. After adjusting tyre

on the front left or right door frame

vehicle, refer to the EEC Certificate of

pressure, switch on ignition and

indicates the original equipment tyres

Conformity provided with your vehicle

select the appropriate setting on the

and the correspondent tyre

or other national registration

page Tyre load in the Driver

pressures.

documents.

Information Centre, 3 116.

The tyre pressure data refers to cold

The driver is responsible for correct

Temperature dependency

tyres. It applies to summer and winter

adjustment of tyre pressure.

tyres.

The tyre pressure depends on the

Always inflate the spare tyre to the

9 Warning

temperature of the tyre. During

pressure specified for full load.

driving, tyre temperature and

If the pressure is too low, this can

pressure increase. Tyre pressure

The ECO tyre pressure serves to

result in considerable tyre warm-

values provided on the tyre

achieve the smallest amount of fuel

up and internal damage, leading to

information label and tyre pressure

consumption possible.

tread separation and even to tyre

chart are valid for cold tyres, which

Incorrect tyre pressures will impair

blow-out at high speeds.

means at 20 °C.

safety, vehicle handling, comfort and

The pressure increases by nearly

fuel economy and will increase tyre

1.5 psi for a 10 °C temperature

wear.

9 Warning

increase. This must be considered

Tyre pressures differ depending on

when warm tyres are checked.

For specific tyres the

various options. For the correct tyre

recommended tyre pressure as

The tyre pressure value displayed in

pressure value, follow the procedure

shown in the tyre pressure table

the Driver Information Centre shows

below:

may exceed the maximum tyre

the real tyre pressure. A cooled down

1. Identify the engine identifier code.

pressure as indicated on the tyre.

tyre will show a decreased value,

Engine data 3 266.

Never exceed the maximum tyre

which does not indicate an air leak.

2. Identify the respective tyre.

pressure as indicated on the tyre.

The tyre pressure tables show all

If the tyre pressure must be reduced

possible tyre combinations 3 272.

or increased on a vehicle with tyre

pressure monitoring system, switch

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

237

System status and pressure warnings

Tyre pressure monitoring

are displayed by a message

system

indicating the corresponding tyre in

The tyre pressure monitoring system

the Driver Information Centre.

checks the pressure of all four tyres

The system considers the tyre

once a minute when vehicle speed

temperature for the warnings.

exceeds a certain limit.

Caution

Tyre pressure monitoring system

warns only about low tyre pressure

condition and does not replace

Select the menu by the buttons on the

regular tyre maintenance by the

turn signal lever.

A detected low tyre pressure

driver.

condition is indicated by control

indicator w 3 114.

All wheels must be equipped with

pressure sensors and the tyres must

If w illuminates, stop as soon as

have the prescribed pressure.

possible and inflate the tyres as

recommended 3 272.

Notice

In countries where the tyre pressure

If w flashes for 60-90 seconds and

monitoring system is legally

then illuminates continuously, there is

required, the use of wheels without

a fault in the system. Consult a

pressure sensors will invalidate the

workshop.

vehicle type approval.

After inflating, some driving may be

required to update the tyre pressure

The current tyre pressures can be

values in the Driver Information

shown in the Driver Information

Centre. During this time w may

Centre.

Select Tyre pressure page under

illuminate.

Vehicle Information Menu

?3 116.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

238

Vehicle care

If w illuminates at lower temperatures

Each time the tyres are replaced, tyre

and extinguishes after some driving,

pressure monitoring system sensors

this could be an indicator for

must be dismounted and serviced.

approaching a low tyre pressure

For the screwed sensor: replace

condition. Check tyre pressure.

valve core and sealing ring. For

clipped sensor: replace complete

Vehicle messages 3 122.

valve stem.

If the tyre pressure must be reduced

or increased, switch off ignition.

Vehicle loading status

Only mount wheels with pressure

Adjust tyre pressure to load condition

sensors, otherwise the tyre pressure

according to the tyre information label

will not be displayed and w

or tyre pressure chart 3 272, and

illuminates continuously.

select the appropriate setting in the

Select Tyre load page under Vehicle

A temporary spare wheel is not

Tyre load menu in the Driver

Information Menu

in the Driver

equipped with pressure sensors. The

Information Centre 3 116. This

Information Centre 3 116.

tyre pressure monitoring system is

setting is the reference for the tyre

Select:

not operational for these wheels.

pressure warnings.

Control indicator w illuminates. For

● Light for comfort pressure up to

The Tyre load menu only appears if

the further three wheels the system

3 people.

the vehicle is at a standstill and the

remains operational.

parking brake is applied. On vehicles

● Eco for Eco pressure up to

The use of commercially available

with automatic transmission the

3 people.

liquid tyre repair kits can impair the

selector lever has to be in P.

● Max for full load.

function of the system. Factory-

approved repair kits can be used.

Tyre pressure sensor matching

Operating electronic devices or being

process

close to facilities using similar wave

Each tyre pressure sensor has a

frequencies could disrupt the tyre

unique identification code. The

pressure monitoring system.

identification code must be matched

to a new wheel position after rotating

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

239

the wheels or exchanging the

2. Turn the ignition on.

6. Press SET/CLR to begin the

complete wheel set and if one or more

sensor matching process. A

3. On vehicles with automatic

tyre pressure sensors were replaced.

message requesting acceptance

transmission: set the selector

The tyre pressure sensor matching

of the process should be

lever to P.

process should also be performed

displayed.

On vehicles with manual

after replacing a spare wheel with a

7. Press SET/CLR again to confirm

transmission: select neutral.

road wheel containing the tyre

the selection. The horn sounds

pressure sensor.

4. Press MENU on the turn signal

twice to indicate the receiver is in

lever to select the Vehicle

The malfunction light w and the

relearn mode.

Information Menu

in the

warning message or code should

8. Start with the left side front wheel.

Driver Information Centre.

extinguish at the next ignition cycle.

9. Place the relearn tool against the

The sensors are matched to the

5. Turn the adjuster wheel to scroll to

tyre sidewall, near the valve stem.

wheel positions, using a relearn tool,

the tyre pressure menu.

Then press the button to activate

in the following order: left side front

the tyre pressure sensor. A horn

wheel, right side front wheel, right

chirp confirms that the sensor

side rear wheel and left side rear

identification code has been

wheel. The turn signal light at the

matched to this wheel position.

current active position is illuminated

until sensor is matched.

10. Proceed to the right side front

wheel, and repeat the procedure

Consult your workshop for service.

in Step 9.

There are two minutes to match the

first wheel position, and five minutes

11. Proceed to the right side rear

overall to match all four wheel

wheel, and repeat the procedure

positions. If it takes longer, the

in Step 9.

matching process stops and must be

12. Proceed to the left side rear

restarted.

wheel, and repeat the procedure

The tyre pressure sensor matching

in Step 9. The horn sounds twice

process is:

to indicate the sensor

identification code has been

1. Apply the parking brake.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

240

Vehicle care

matched to the left side rear tyre,

Changing tyre and wheel

and the tyre pressure sensor

size

matching process is no longer

active.

If tyres of a different size than those

fitted at the factory are used, it may be

13. Turn off the ignition.

necessary to reprogramme the

14. Set all four tyres to the

speedometer as well as the nominal

recommended air pressure level

tyre pressure and make other vehicle

as indicated on the tyre pressure

modifications.

information label.

After converting to a different tyre

15. Ensure the tyre loading status is

size, have the label with tyre

set according to the selected

pressures replaced.

pressure 3 116.

The legally permissible minimum

tread depth (1.6 mm) has been

9 Warning

Tread depth

reached when the tread has worn

Use of unsuitable tyres or wheels

Check tread depth at regular

down as far as one of the tread wear

may lead to accidents and will

intervals.

indicators (TWI). Their position is

invalidate the vehicle type

indicated by markings on the

Tyres should be replaced for safety

approval.

sidewall.

reasons at a tread depth of 2-3 mm

(4 mm for winter tyres).

If there is more wear at the front than

Wheel covers

the rear, swap round front wheels and

For safety reasons, it is

rear wheels periodically. Ensure that

Wheel covers and tyres that are

recommended that the tread depth of

the direction of rotation of the wheels

factory approved for the respective

the tyres on one axle should not vary

remains the same.

vehicle and comply with all of the

by more than 2 mm.

Tyres age, even if they are not used.

relevant wheel and tyre combination

We recommend tyre replacement

requirements must be used.

every 6 years.

If the wheel covers and tyres used are

not factory approved, the tyres must

not have a rim protection ridge.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

241

Vehicle care

Wheel covers must not impair brake

Tyre chains are only permitted on the

9 Warning

cooling.

front wheels.

Always use fine mesh chains that add

Do not drive faster than 50 mph.

9 Warning

no more than 10 mm to the tyre tread

Do not use for a lengthy period.

and the inboard sides (including chain

Use of unsuitable tyres or wheel

lock).

Steering and handling may be

covers could lead to sudden

affected.

pressure loss and thereby

9 Warning

accidents.

If you have a flat tyre:

Damage may lead to tyre blowout.

Apply the parking brake and engage

Vehicles with steel wheels: When

first gear, reverse gear or P.

using locking wheel nuts, do not

Tyre chains are only permitted on

attach wheel covers.

tyres of size 215/60 R16 and

225/50 R17.

Tyre chains

The use of tyre chains is not permitted

on the temporary spare wheel.

Tyre repair kit

Minor damage to the tyre tread can be

repaired with the tyre repair kit.

Do not remove foreign bodies from

the tyres.

Tyre damage exceeding 4 mm or that

The tyre repair kit is on the left side in

is at the tyre's sidewall cannot be

the load compartment behind a cover.

repaired with the tyre repair kit.

1. Take the tyre repair kit from the

compartment.

2. Remove the compressor.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

242

Vehicle care

4. Screw the compressor air hose to

9. Connect the compressor plug to

the connection on the sealant

the power outlet or cigarette

bottle.

lighter socket.

5. Fit the sealant bottle into the

To avoid discharging the battery,

retainer on the compressor.

we recommend running the

engine.

Set the compressor near the tyre

in such a way that the sealant

bottle is upright.

3. Remove the electrical connection

cable and air hose from the

stowage compartments on the

underside of the compressor.

10. Set the rocker switch on the

compressor to I. The tyre is filled

with sealant.

6. Unscrew valve cap from defective

tyre.

11. The compressor pressure gauge

briefly indicates up to six bar

7. Screw the filler hose to the tyre

whilst the sealant bottle is

valve.

emptying (approx. 30 seconds).

8. The switch on the compressor

Then the pressure starts to drop.

must be set to J.

12. All of the sealant is pumped into

the tyre. Then the tyre is inflated.

Vauxhall New Zafira (2016 year). Manual - part 14