Vauxhall New Zafira (2016 year). Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

158

Driving and operating

AdBlue

Level warnings

Caution

Depending on the calculated range of

General information

Avoid contact of the paintwork with

AdBlue, different messages are

The selective catalytic reduction

AdBlue.

displayed in the Driver Information

(BlueInjection) is a method to

In case of contact, rinse off with

Centre. The messages and the

substantially reduce the nitrogen

water.

restrictions are a legal requirement.

oxides in the exhaust emission. This

The first possible warning is AdBlue

is achieved by injecting a Diesel

AdBlue freezes at a temperature of

Range: 1500 mi.

Exhaust Fluid into the exhaust

approx. -11 °C. As the vehicle is

This warning will show up once briefly

system. The ammonia released by

equipped with an AdBlue pre-heater,

with the calculated range. Driving is

the fluid reacts with nitrous gases

the emissions reduction at low

possible without any restrictions.

(NO_x) from the exhaust and turns it

temperatures is ensured. The AdBlue

into nitrogen and water.

The next warning level is entered with

pre-heater works automatically.

a range below 1090 miles. The

The designation of this fluid is

The typical AdBlue consumption is

message with the current range will

AdBlue^®. It is a non-toxic, non-

approx. two litres per 600 miles, but

always be displayed when ignition is

flammable, colourless and odourless

can also be higher depending on

switched on and needs to be

fluid which consists of 32% urea and

driving behaviour (e.g. high load or

confirmed 3 116. Refill AdBlue before

68% water.

towing).

entering the next warning level.

AdBlue tank

At an AdBlue range below 560 miles,

9 Warning

the following warning messages are

At a remaining volume of approx. five

alternately displayed and cannot be

Avoid contact of your eyes or skin

litres, there is a liquid level switch.

dismissed:

with AdBlue.

Warning messages are displayed

● AdBlue Low Refill Now

In case of eye or skin contact,

only below that threshold. Tank

rinse off with water.

volume 3 271.

● Engine Restart Prevented in 560

miles.

Additionally, control indicator Y

flashes continuously.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

159

Notice

High emission warnings

Notice

In case of high AdBlue consumption,

Whenever a filling pump with a

If the exhaust emission rises above a

the Driver Information Centre may

nozzle for passenger cars is not

certain value, warnings similar to the

display this warning without the

available at a filling station, use only

range warnings will be displayed in

previous warning stages.

AdBlue bottles or canisters with a

the Driver Information Centre.

sealed refill adapter for refilling, to

The last warning level is entered

Requests to have the exhaust system

prevent splashback and overspill,

when the AdBlue tank is empty.

checked and finally the

and in order to ensure that the fumes

Restart of the engine is not possible.

announcement of the prevention of

from the tank are captured and do

The following warning messages are

an engine restart are displayed.

not emerge. AdBlue in bottles or

alternately displayed and cannot be

These restrictions are a legal

canisters is available in many filling

dismissed:

requirement.

stations and can be purchased e.g.

● AdBlue Empty Refill Now

at Vauxhall dealers and other retail

Consult a workshop for assistance.

● Engine Will Not Restart.

outlets.

Additionally, control indicator Y

Refilling AdBlue

Since AdBlue has a limited

flashes continuously.

durability, check the date of expiry

Caution

before refilling.

With active prevention of an engine

start, the following message will be

Notice

Only use AdBlue that complies

displayed:

The refilling of AdBlue is only

with European standards

detected by the system when the

Refill AdBlue To Start Vehicle.

DIN 70 070 and ISO 22241-1.

abovementioned liquid level switch

The tank must be refilled completely

Do not use additives.

in the tank is activated.

with AdBlue, otherwise restarting of

Do not dilute AdBlue.

In case AdBlue refill is not

the engine is not possible.

Otherwise the selective catalytic

successfully detected:

reduction system could be

damaged.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

160

Driving and operating

1. Continuously drive the vehicle

The vehicle must be parked on a level

5. Open AdBlue canister.

for 10 minutes making sure that

surface.

6. Mount one end of the hose on the

vehicle speed is always higher

The filler neck for AdBlue is located

canister and screw the other end

than 12 mph.

behind the fuel filler flap, which is

on the filler neck.

2. If AdBlue refill is detected

located at right rear side of the

7. Lift the canister until it is empty, or

successfully, AdBlue supply-

vehicle.

until the flow from the canister has

driven limitations will disappear.

The fuel filler flap can only be opened

stopped. This can take up to five

If AdBlue refill is still not detected,

if the vehicle is unlocked.

minutes.

seek the assistance of a workshop.

1. Remove key from ignition switch.

8. Place the canister on the ground

If AdBlue must be refilled at

to empty the hose, wait 15

2. Close all doors to avoid ammonia

temperatures below -11 °C, the

seconds.

fumes entering the interior of the

refilling of AdBlue may not be

vehicle.

9. Unscrew the hose from the filler

detected by the system. In this

neck.

3. Release the fuel filler flap by

event, park the vehicle in a space

pushing the flap 3 201.

10. Mount the protective cap and turn

with a higher ambient temperature

clockwise until it engages.

until AdBlue is liquefied.

Notice

Dispose of AdBlue canister

When unscrewing the protective cap

according to environmental

from the filler neck, ammonia fumes

requirements. Hose can be reused

may emerge. Do not inhale as the

after flushing with clear water before

fumes have a pungent smell. The

AdBlue dries out.

fumes are not harmful by inhalation.

The AdBlue tank should be filled

completely. This must be done if the

warning message regarding

prevention of an engine restart is

already displayed.

4. Unscrew protective cap from the

filler neck.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

161

In manual mode, M and the number

< : upshift in manual mode

Automatic transmission

of the selected gear is indicated.

] : downshift in manual mode

The automatic transmission permits

R indicates reverse gear.

automatic gearshifting (automatic

N indicates neutral position.

mode) or manual gearshifting

P indicates park position.

(manual mode).

Manual shifting is possible in manual

Selector lever

mode M by tapping the selector lever

to + or - 3 162.

Transmission display

The selector lever is locked in P and

can only be moved when the ignition

is on, the release button on the

selector lever is pushed and the brake

pedal is applied.

Without brake pedal applied, the

P : park position, wheels are locked,

control indicator j illuminates.

engage only when the vehicle is

If the selector lever is not in P when

stationary and the parking brake

the ignition is switched off, control

is applied

indicator j flashes.

The mode or selected gear is shown

R : reverse gear, engage only when

To engage P or R, press the release

in the Driver Information Centre.

the vehicle is stationary

button.

N : neutral

In automatic mode, the driving

D : automatic mode

programme is indicated by D.

M : manual mode

-------------------------------------------------------------------------------------------------------------------------------------------------------------

162

Driving and operating

The engine can only be started with

Parking

If a higher gear is selected when

the lever in position P or N. When

vehicle speed is too low, or a lower

Apply the parking brake and engage

position N is selected, press the brake

gear when vehicle speed is too high,

pedal or apply the parking brake

the shift is not executed. This can

before starting.

The ignition key can only be removed

cause a message in the Driver

when the selector lever is in position

Information Centre.

Do not accelerate while engaging a

gear. Never depress the accelerator

In manual mode, no automatic

pedal and brake pedal at the same

shifting to a higher gear takes place

time.

Manual mode

at high engine revolutions.

When a gear is engaged, the vehicle

Gear shift indication

slowly begins to creep when the

brake is released.

The symbol R with a number beside

it is indicated when gearshifting is

Engine braking

recommended for fuel saving

reasons.

To utilise the engine braking effect,

select a lower gear in good time when

Shift indication appears only in

driving downhill, see manual mode.

manual mode.

Rocking the vehicle

Electronic driving

Rocking the vehicle is only

programmes

permissible if the vehicle is stuck in

sand, mud or snow. Move the selector

● Following a cold start, the

Move selector lever out of position D

lever between D and R in a repeat

operating temperature

towards the left in position M.

pattern. Do not race the engine and

programme increases engine

Tap selector lever upwards + to shift

speed to quickly bring the

avoid sudden acceleration.

to a higher gear.

catalytic converter to the required

Tap the selector lever downwards - to

temperature.

shift to a lower gear.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

163

●

The automatic neutral shift

Fault

function automatically shifts gear

In the event of a fault a message is

to idling when the vehicle is

displayed in the Driver Information

stopped with a forward gear

Centre. Vehicle messages 3 122.

engaged and the brake pedal is

pressed.

The transmission no longer shifts

automatically. Continued travel is

●

When SPORT mode is engaged,

possible with manual shifting.

the vehicle shifts at higher engine

speeds (unless cruise control is

Only the highest gear is available.

on). SPORT mode 3 170.

Depending on the fault, 2nd gear may

also be available in manual mode.

●

Special programmes

Shift only when vehicle is at a

automatically adapt the gearshift

standstill.

points when driving up inclines or

2. Release the selector lever trim

down hills.

Have the cause of the fault remedied

from the centre console at the

by a workshop.

front, fold it upwards and rotate it

●

In snowy or icy conditions or on

to the left.

other slippery surfaces, the

electronic transmission control

Interruption of power supply

enables the driver to select

In the event of an interruption of

manually first, second or third

power supply, the selector lever

gear for starting off.

cannot be moved out of the P

position. The ignition key cannot be

Kickdown

removed from the ignition switch.

If the accelerator pedal is pressed

If the vehicle battery is discharged,

down completely in automatic mode,

start the vehicle using jump leads

the transmission shifts to a lower gear

3 250.

depending on engine speed.

If the vehicle battery is not the cause

of the fault, release the selector lever.

1. Apply the parking brake.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

164

Driving and operating

3. Push down the release lever and

Manual transmission

Caution

move the selector lever out of P or

N. If these positions are engaged

It is not advisable to drive with the

again, the selector lever will be

hand resting on the selector lever.

locked in position again. Have the

cause of the power supply

Gear shift indication 3 113.

interruption remedied by a

workshop.

Stop-start system 3 153.

4. Mount the selector lever trim onto

the centre console and refit.

To engage reverse, depress the

clutch pedal and then press the

release button on the selector lever

and engage the gear.

If the gear does not engage, set the

lever to neutral, release the clutch

pedal and depress again; then repeat

gear selection.

Do not slip the clutch unnecessarily.

When operating, depress the clutch

pedal completely. Do not use the

pedal as a foot rest.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

165

ABS starts to regulate brake pressure

Fault

Brakes

as soon as a wheel shows a tendency

to lock. The vehicle remains

The brake system comprises two

9 Warning

steerable, even during hard braking.

independent brake circuits.

ABS control is made apparent

If there is a fault in the ABS, the

If a brake circuit fails, the vehicle can

through a pulse in the brake pedal

wheels may be liable to lock due

still be braked using the other brake

and the noise of the regulation

to braking that is heavier than

circuit. However, braking effect is

process.

normal. The advantages of ABS

achieved only when the brake pedal

are no longer available. During

is depressed firmly. Considerably

For optimum braking, keep the brake

hard braking, the vehicle can no

more force is needed for this. The

pedal fully depressed throughout the

longer be steered and may

braking distance is extended. Seek

braking process, despite the fact that

swerve.

the assistance of a workshop before

the pedal is pulsating. Do not reduce

continuing your journey.

the pressure on the pedal.

Have the cause of the fault remedied

When the engine is not running, the

After starting off the system performs

by a workshop.

support of the brake servo unit

a self-test which may be audible.

disappears once the brake pedal has

Parking brake

been depressed once or twice.

Braking effect is not reduced, but

braking requires significantly greater

9 Warning

force. It is especially important to bear

this in mind when being towed.

Before leaving the vehicle, check

parking brake status. Control

Control indicator R 3 111.

Control indicator u 3 112.

indicator R (manual parking

brake) or m (electrical parking

Antilock brake system

Adaptive brake light

brake) must illuminate constantly.

Antilock brake system (ABS)

During full braking, all three brake

prevents the wheels from locking.

lights flash for the duration of ABS

control.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

166

Driving and operating

Manual parking brake

Control indicator R 3 111.

3 112. The electric parking brake

operates automatically with

Electric parking brake

adequate force.

Before leaving the vehicle, check

the electric parking brake status.

Control indicator m 3 112.

The electric parking brake can always

be activated, even if the ignition is off.

Do not operate electric parking brake

system too often with engine not

running, as this will discharge the

vehicle battery.

9 Warning

Releasing

Applying when vehicle is stationary

Switch on ignition. Keep foot brake

Always apply parking brake firmly

pedal depressed and then push

without operating the release

switch m.

9 Warning

button, and apply as firmly as

possible on a downhill or uphill

Drive away function

Pull switch m for a minimum of

slope.

Vehicles with manual transmission:

one second until control indicator

Depressing the clutch pedal and then

To release the parking brake, pull

m illuminates constantly and

slightly releasing the clutch pedal and

the lever up slightly, press the

electric parking brake is applied

slightly depressing the accelerator

release button and fully lower the

pedal releases the electric parking

lever.

brake automatically. This is not

To reduce the operating forces of

possible when the switch m is pulled

the parking brake, depress the

at the same time.

foot brake at the same time.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

167

Vehicles with automatic transmission:

Apply electric parking brake: pull and

Maintain steady pressure on the

Engaging D and then depressing the

hold switch m for more than five

brake pedal as long as full braking is

accelerator pedal releases the

seconds. If control indicator m

required. Maximum brake force is

electric parking brake automatically.

illuminates, electric parking brake is

automatically reduced when brake

This is not possible when the switch

applied.

pedal is released.

m is pulled at the same time.

Release electric parking brake: push

and hold the switch m for more than

Hill start assist

Dynamic braking when vehicle is

two seconds. If control indicator m

moving

The system helps prevent unintended

extinguishes, electric parking brake is

When the vehicle is moving and the

movement when driving away on

released.

switch m is kept pulled, the electric

inclines.

parking brake system will decelerate

Control indicator m flashes: electric

When releasing the brake pedal after

the vehicle, but will not apply

parking brake is not fully applied or

stopping on an incline, the brakes

statically.

released. When continuously

remain on for a further two seconds.

flashing, release electric parking

As soon as the switch m is released,

The brakes release automatically as

brake and retry applying.

dynamic braking will be stopped.

soon as the vehicle begins to

accelerate or the two seconds holding

Functionality check

Brake assist

time is over.

When the vehicle is not moving, the

The hill start assist is not active during

If brake pedal is depressed quickly

electric parking brake might be

an Autostop.

and forcefully, maximum brake force

applied automatically. This is done to

is automatically applied.

check the system.

Operation of brake assist might

Fault

become apparent by a pulse in the

Failure mode of electric parking brake

brake pedal and a greater resistance

is indicated by a control indicator j

when depressing the brake pedal.

and by a vehicle message which is

displayed in the Driver Information

Centre. Vehicle messages 3 122.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

168

Driving and operating

A status message appears in the

Ride control systems

9 Warning

Driver Information Centre when TC is

deactivated.

Traction Control system

Do not let this special safety

The Traction Control system (TC) is a

feature tempt you into taking risks

component of the Electronic Stability

when driving.

Control.

Adapt speed to the road

TC improves driving stability when

conditions.

necessary, regardless of the type of

road surface or tyre grip, by

Control indicator b 3 113.

preventing the drive wheels from

Control indicator k illuminates.

Deactivation

spinning.

When TC is deactivated, ESC

As soon as the drive wheels starts to

remains active but with higher control

spin, engine output is reduced and

threshold.

the wheel spinning the most is braked

TC is reactivated by pressing b

individually. This considerably

again. A status message pops-up in

improves the driving stability of the

the Driver Information Centre when

vehicle on slippery road surfaces.

TC is reactivated.

TC is also reactivated the next time

the ignition is switched on.

Fault

If there is a fault in the system the

control indicator b illuminates

TC can be switched off when spinning

TC is operational after each engine

continuously and a message appears

of drive wheels is required: press b

start as soon as the control indicator

in the Driver Information Centre. The

briefly.

b extinguishes.

system is not operational.

When TC operates b flashes.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

169

Have the cause of the fault remedied

illuminate and status messages

9 Warning

by a workshop.

appear in the Driver Information

Centre.

Do not let this special safety

Electronic Stability Control

feature tempt you into taking risks

Electronic Stability Control (ESC)

when driving.

improves driving stability when

Adapt speed to the road

necessary, regardless of the type of

conditions.

road surface or tyre grip.

As soon as the vehicle starts to

Control indicator b 3 113.

●

To deactivate only Traction

swerve (understeer/oversteer),

Deactivation

control system press button b

engine output is reduced and the

briefly: TC is inactive but ESC

wheels are braked individually.

remains active, k illuminates. A

ESC operates in combination with the

status message appears in the

Traction Control system (TC). It

Driver Information Centre when

prevents the drive wheels from

TC is deactivated.

spinning.

ESC is reactivated by pressing the

b button again. If the TC system was

previously disabled, both TC and

ESC are reactivated. k and n

extinguishes when TC and ESC are

reactivated.

ESC is also reactivated the next time

ESC is operational after each engine

the ignition is switched on.

ESC and TC can be deactivated:

start as soon as the control indicator

● hold b pressed for a minimum of

b extinguishes.

five seconds: ESC and TC are

When ESC operates b flashes.

both deactivated. k and n

-------------------------------------------------------------------------------------------------------------------------------------------------------------

170

Driving and operating

Fault

In each driving mode Flex Ride

The settings of the systems are

networks the following electronic

adapted to a sportier driving style:

If there is a fault in the system the

systems:

● Damping of shock absorbers

control indicator b illuminates

● Continuous Damping Control

reacts more stiffly to provide

continuously and a message appears

better contact with the road

in the Driver Information Centre. The

● Accelerator Pedal Control

surface.

system is not operational.

● Steering Control

● The engine reacts more quickly

Have the cause of the fault remedied

● Automatic transmission

to the accelerator pedal.

by a workshop.

SPORT mode

● Steering support is reduced.

● Shift points of automatic

Interactive driving system

transmission occur later.

Flex Ride

TOUR mode

Flex Ride driving system allows the

driver to select between three driving

modes:

● SPORT mode: press SPORT,

LED illuminates.

● TOUR mode: press TOUR, LED

illuminates.

● Normal mode: neither SPORT or

TOUR are pressed, no LED

illuminates.

Deactivate SPORT mode and TOUR

mode by pressing the corresponding

button once more.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

171

The settings of the systems are

recognising greater variations, the

Select the relevant settings in

adapted to a comfort driving style:

driving mode is changed for the

Settings in the Info-Display.

length of variation.

● Damping of shock absorbers

Info-Display 3 121.

reacts more softly.

If, for example, Normal mode is

Vehicle personalisation 3 124.

selected and DMC detects a sporty

● Accelerator pedal reacts with

driving behaviour, DMC changes

standard settings.

several settings of the Normal mode

● Steering support is in standard

into sporty settings. The DMC

mode.

changes to SPORT mode in case of

● Shift points of automatic

very sporty driving behaviour.

transmission occur in a comfort

If, for example, TOUR mode is

mode.

selected and whilst driving on a

winding road a sudden hard brake is

Normal mode

necessary, DMC will detect the

All settings of the systems are

dynamic vehicle condition and

adapted to standard values.

changes the settings for suspension

to SPORT mode to increase vehicle

Drive mode control

stability.

Within each manual selected driving

When the driving characteristic or the

mode SPORT, TOUR or Normal, the

dynamic vehicle state returns to

Drive Mode Control (DMC) detects

former state, DMC will change the

and analyses continuously the real

settings to the preselected driving

driving characteristics, responses by

mode.

the driver, and the active dynamic

state of the vehicle. If necessary, the

Personalised settings in the Sport

control unit of DMC automatically

mode

changes the settings within the

selected driving mode or, when

The driver can select the functions of

the SPORT mode when SPORT is

pressed.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

172

Driving and operating

Press m; control indicator m in

Driver assistance

instrument cluster illuminates white.

systems

Activation

Accelerate to the desired speed and

9 Warning

turn thumb wheel to SET/-, the

current speed is stored and

Driver assistance systems are

maintained. Control indicator m in

developed to support the driver

instrument cluster illuminates green.

and not to replace the driver's

Accelerator pedal can be released.

attention.

Vehicle speed can be increased by

The driver accepts full

depressing the accelerator pedal.

responsibility when driving the

Do not use the cruise control if it is not

When the accelerator pedal is

vehicle.

advisable to maintain a constant

released, the previously stored speed

When using driver assistance

speed.

is resumed.

systems, always take care

With automatic transmission, only

Cruise control remains activated

regarding the current traffic

activate cruise control in automatic

while gearshifting.

situation.

mode.

Increase speed

Control indicator m 3 115.

Cruise control

With cruise control active, hold thumb

The cruise control can store and

Switching on

wheel turned to RES/+ or briefly turn

maintain speeds of approx. 20 mph to

to RES/+ repeatedly: speed

maximum vehicle speed. Deviations

increases continuously or in small

from the stored speeds may occur

increments.

when driving uphill or downhill.

Alternatively accelerate to the desired

For safety reasons, the cruise control

speed and store by turning to SET/-.

cannot be activated until the foot

brake has been operated once.

Activation in first gear is not possible.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

173

Automatic deactivation:

Switching off

●

Vehicle speed is below approx.

Press m, control indicator m in

20 mph.

instrument cluster extinguishes. The

●

Vehicle speed drops more than

stored speed is deleted.

15 mph below the set speed.

Pressing L to activate the speed

●

The brake pedal is depressed.

limiter or switching off the ignition also

●

The clutch pedal is depressed for

switches off cruise control and

a few seconds.

deletes the stored speed.

●

Selector lever is in N.

Speed limiter

●

Engine speed is in a very low

range.

The speed limiter prevents the

Reduce speed

●

The Traction Control system or

vehicle exceeding a preset maximum

Electronic Stability Control is

speed.

With cruise control active, hold thumb

operating.

The maximum speed can be set at

wheel turned to SET/- or briefly turn to

SET/- repeatedly: speed decreases

●

Parking brake is applied.

speeds above 15 mph up to

continuously or in small increments.

125 mph.

●

Simultaneous pressing RES/+

and brake pedal deactivates

The driver can only accelerate up to

Deactivation

cruise control and will delete

the preset speed. Deviations from the

Press y, control indicator m in

stored speed.

limited speed may occur when driving

downhill.

instrument cluster illuminates white.

Resume stored speed

The preset speed limit is displayed in

Cruise control is deactivated, but not

the Driver Information Centre when

switched off. Last stored speed

Turn thumb wheel to RES/+ at a

the system is active.

remains in memory for later speed

speed above 20 mph. The stored

resume.

speed will be obtained.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

174

Driving and operating

Activation

Deactivation

Press y: speed limiter is deactivated

and the vehicle can be driven without

speed limit.

Change speed limit

With speed limiter active, turn thumb

wheel to RES/+ to increase or SET/-

to decrease the desired maximum

speed.

The stored limited speed is indicated

in brackets. Additionally, a

Exceeding the speed limit

corresponding message appears.

Press L. Symbol Lilluminates in the

When exceeding the limited speed

Driver Information Centre.

Speed limiter is deactivated, but not

without driver input, the speed will

switched off. Last stored speed

If cruise control or adaptive cruise

flash in the Driver Information Centre

remains in memory for later speed

control has been activated before, it

and a chime sounds during this

resume.

is switched off when speed limiter is

period.

activated and the control indicator m

In the event of an emergency, it is

Resume limit speed

extinguishes.

possible to exceed the speed limit by

Turn thumb wheel to RES/+. The

depressing the accelerator pedal

Set speed limit

stored speed limit will be obtained

firmly nearly to the final point. In this

and is indicated without brackets in

Accelerate to the desired speed and

case no chime appears.

the Driver Information Centre.

briefly turn thumb wheel to SET/-: the

Release the accelerator pedal and

current speed is stored as maximum

the speed limiter function is

speed. L and the speed limit is

reactivated once a speed lower than

displayedin the Driver Information

the limit speed is obtained.

Centre.

Vauxhall New Zafira (2016 year). Manual - part 10