Vauxhall Mokka X (2016 year). Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

192

Vehicle care

No. Circuit

Body control module

Ultrasonic park assist module

Instrument panel cluster

Body control module

Body control module/Regulated

Infotainment system

voltage control

Body control module

Trailer socket

Steering wheel

Body control module

Passive entry/Passive start

module

Body control module

Cigarette lighter/DC accessory

S/B Fuses

Body control module

power outlet (front)

No.

Circuit

Body control module

Cigarette lighter/DC accessory

Body control module

power outlet (rear center

Power seat switch

console)

Ignition switch

Spare

Safety diagnosis module

Power windows front

Telematics service module

Data link connector

Power windows rear

Heated steering wheel

Climate control

Logistic mode

Instrument panel cluster/Info-

Tailgate

Power seat switch

tainment system/Auxiliary

heater switch

Spare

Central gateway module

Trailer socket

Spare

Lane departure warning/Interior

mirror

Display/Infotainment system

Adaptive forward lighting

Transmission control module

Column lock

-------------------------------------------------------------------------------------------------------------------------------------------------------------

194

Vehicle care

No.

Circuit

Vehicles with spare wheel

Vehicle tools

Tools

Vehicles with tyre repair kit

S/B Fuses

No. Circuit

The jack and the tools are in a storage

compartment in the load

compartment above the spare wheel.

Wheel changing 3 205, spare wheel

DC/DC 400W transformer

The tools and tyre repair kit are in the

3 207.

right side of the load compartment.

DC/DC 400W transformer

3 202.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

195

Wheels and tyres

Tyre designations

Directional tyres

E.g. 215/60 R 16 95 H

Fit directional tyres such that they roll

Tyre condition, wheel condition

215 : tyre width, mm

in the direction of travel. The rolling

: cross-section ratio (tyre height

direction is indicated by a symbol

Drive over edges slowly and at right

(e.g. an arrow) on the sidewall.

to tyre width), percentage

angles if possible. Driving over sharp

: belt type: Radial

edges can cause tyre and wheel

RF : type: RunFlat

Tyre pressure

damage. Do not trap tyres on the kerb

: wheel diameter, inches

when parking.

Check the pressure of cold tyres at

: load index e.g. 95 is equivalent

least every 14 days and before any

Regularly check the wheels for

to 690 kg

long journey. Do not forget the spare

damage. Seek the assistance of a

: speed code letter

wheel. This also applies to vehicles

workshop in the event of damage or

Speed code letter:

with tyre pressure monitoring system.

unusual wear.

Q : up to 100 mph

Unscrew the valve cap.

S : up to 112 mph

Winter tyres

: up to 118 mph

Winter tyres improve driving safety at

H : up to 130 mph

temperatures below 7 °C and should

V : up to 150 mph

therefore be fitted on all wheels.

W : up to 168 mph

All tyre sizes are permitted as winter

Choose a tyre appropriate for the

tyres 3 230.

maximum speed of your vehicle.

In accordance with country-specific

The maximum speed is achievable at

regulations, affix the speed sticker in

kerb weight with driver (75 kg) plus

the driver's field of view.

125 kg payload. Optional equipment

could reduce the maximum speed of

the vehicle.

Performance 3 226.

Tyre pressure 3 230.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

196

Vehicle care

The tyre pressure information label

For the tyres approved for your

Temperature dependency

on the left or right door frame

vehicle, refer to the EEC Certificate of

The tyre pressure depends on the

indicates the original equipment tyres

Conformity provided with your vehicle

temperature of the tyre. During

and the correspondent tyre

or other national registration

driving, tyre temperature and

pressures.

documents.

pressure increase. Tyre pressure

The tyre pressure data refers to cold

The driver is responsible for correct

values provided on the tyre

tyres. It applies to summer and winter

adjustment of tyre pressure.

information label and tyre pressure

tyres.

chart are valid for cold tyres, which

Always inflate the spare tyre to the

9 Warning

means at 20 °C.

pressure specified for full load.

The pressure increases by nearly

If the pressure is too low, this can

The ECO tyre pressure serves to

1.5 psi for a 10 °C temperature

result in considerable tyre warm-

achieve the smallest amount of fuel

increase. This must be considered

up and internal damage, leading to

consumption possible.

when warm tyres are checked.

tread separation and even to tyre

Incorrect tyre pressures will impair

blow-out at high speeds.

The tyre pressure value displayed in

safety, vehicle handling, comfort and

the Driver Information Centre shows

fuel economy and will increase tyre

the real tyre pressure. A cooled down

wear.

9 Warning

tyre will show a decreased value,

Tyre pressures differ depending on

which does not indicate an air leak.

For specific tyres the

various options. For the correct tyre

recommended tyre pressure as

pressure value, follow the procedure

Tyre pressure monitoring

shown in the tyre pressure table

below:

may exceed the maximum tyre

system

1. Identify the engine identifier code.

pressure as indicated on the tyre.

The tyre pressure monitoring system

Engine data 3 224.

Never exceed the maximum tyre

checks the pressure of all four tyres

2. Identify the respective tyre.

pressure as indicated on the tyre.

once a minute when vehicle speed

The tyre pressure tables show all

exceeds a certain limit.

possible tyre combinations 3 230.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

197

Select the Tyre pressure page under

Caution

the Info Menu in the Driver

Information Centre 3 96.

Tyre pressure monitoring system

System status and pressure warnings

warns only about low tyre pressure

are displayed by a message

condition and does not replace

indicating the corresponding tyre in

regular tyre maintenance by the

the Driver Information Centre.

driver.

The system considers the tyre

All wheels must be equipped with

temperature for the warnings.

pressure sensors and the tyres must

Temperature dependency 3 195.

have the prescribed pressure.

Notice

Select the Tyre pressure page under

In countries where the tyre pressure

the Vehicle Information Menu

monitoring system is legally

the Driver Information Centre 3 96.

required, the use of wheels without

pressure sensors will invalidate the

Uplevel display:

vehicle type approval.

A detected low tyre pressure

The current tyre pressures can be

condition is indicated by the control

shown in the Driver Information

indicator w 3 94.

Centre.

If w illuminates, stop as soon as

Midlevel display:

possible and inflate the tyres as

recommended 3 230.

If w flashes for 60-90 seconds and

then illuminates continuously, there is

a fault in the system. Consult a

workshop.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

198

Vehicle care

After inflating, some driving may be

The use of commercially-available

The Tyre load menu only appears

required to update the tyre pressure

liquid tyre repair kits can impair the

when the vehicle is at a standstill and

values in the Driver Information

function of the system. Factory-

the parking brake is applied. On

Centre. During this time w may

approved repair kits can be used.

vehicles with automatic transmission

illuminate.

the selector lever must be in P.

Operating electronic devices or being

If w illuminates at lower temperatures

close to facilities using similar wave

Midlevel display:

and extinguishes after driving, this

frequencies could disrupt the tyre

could be an indicator for approaching

pressure monitoring system.

a low tyre pressure condition. Check

Each time the tyres are replaced, tyre

tyre pressure.

pressure monitoring system sensors

Vehicle messages 3 102.

must be dismounted and serviced.

For the screwed sensor, replace

If the tyre pressure must be reduced

valve core and sealing ring. For the

or increased, switch off ignition.

clipped sensor, replace complete

Only mount wheels with pressure

valve stem.

sensors, otherwise the tyre pressure

will not be displayed and w

Vehicle loading status

illuminates continuously.

Adjust tyre pressure to load condition

A spare wheel or temporary spare

according to tyre information label or

wheel is not equipped with pressure

Select the Tyre load page under the

tyre pressure chart 3 230, and select

sensors. The tyre pressure

Vehicle Information Menu

in the

the appropriate setting in the

monitoring system is not operational

Driver Information Centre 3 96.

menuTyre Load in the Driver

for these tyres. Control indicator w

Information Centre,Vehicle

● Light for comfort pressure up to

illuminates. For the further three

Information Menu 3 96. This setting is

three people.

tyres, the system remains

the reference for the tyre pressure

● Eco for Eco pressure up to three

operational.

warnings.

people.

● Max for full loading.

Uplevel display:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

199

complete wheel set and if one or more

3. On vehicles with automatic

tyre pressure sensors were replaced.

transmission: set the selector

The tyre pressure sensor matching

lever to P.

process should also be performed

On vehicles with manual

after replacing a spare wheel with a

transmission: select neutral.

road wheel containing a tyre pressure

4. Press MENU on the turn signal

sensor.

lever to select the Vehicle

The malfunction light w and the

Information Menu in the Driver

warning message should extinguish

Information Centre.

at the next ignition cycle. The sensors

5. Turn the adjuster wheel to scroll to

are matched to the wheel positions,

the tyre pressure menu.

using a relearn tool, in the following

order: left side front wheel, right side

Midlevel display:

Select the Tyre load page under the

front wheel, right side rear wheel and

Options Menu in the Driver

left side rear wheel. The turn signal

Information Centre 3 96.

light at the current active position is

● Light for comfort pressure up to

illuminated until sensor is matched.

three people.

Consult a workshop for service. There

● Eco for Eco pressure up to three

are two minutes to match the first

people.

wheel position, and five minutes

● Max for full loading.

overall to match all four wheel

positions. If it takes longer, the

Tyre pressure sensor matching

matching process stops and must be

process

restarted.

Each tyre pressure sensor has a

The tyre pressure sensor matching

Uplevel display:

unique identification code. The

process is:

identification code must be matched

1. Apply the parking brake.

to a new wheel position after rotating

2. Turn the ignition on.

the wheels or exchanging the

-------------------------------------------------------------------------------------------------------------------------------------------------------------

200

Vehicle care

identification code has been

Tread depth

matched to this tyre and wheel

Check tread depth at regular

position.

intervals.

10. Proceed to the right side front

Tyres should be replaced for safety

wheel, and repeat the procedure

reasons at a tread depth of 2-3 mm

in Step 9.

(4 mm for winter tyres).

11. Proceed to the right side rear

For safety reasons it is recommended

wheel, and repeat the procedure

that the tread depth of the tyres on

in Step 9.

one axle should not vary by more than

12. Proceed to the left side rear

2 mm.

wheel, and repeat the procedure

in Step 9. The horn sounds twice

6. Press SET/CLR to begin the

to indicate the sensor

sensor matching process. A

identification code has been

message requesting acceptance

matched to the left side rear

of the process should be

wheel, and the tyre pressure

displayed.

sensor matching process is no

7. Press SET/CLR again to confirm

longer active.

the selection. The horn sounds

13. Turn off the ignition.

twice to signal that the receiver is

in relearn mode.

14. Set all four tyres to the

recommended air pressure level

8. Start with the left side front wheel.

as indicated on the tyre pressure

9. Place the relearn tool against the

information label.

tyre sidewall, near the valve stem.

The legally permissible minimum

15. Ensure the tyre loading status is

Then press the button to activate

tread depth (1.6 mm) has been

set according to the selected tyre

the tyre pressure sensor. A horn

reached when the tread has worn

pressure 3 96.

chirp confirms that the sensor

down as far as one of the tread wear

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

201

indicators (TWI). Their position is

Vehicles with alloy wheels: When

9 Warning

indicated by markings on the

mounting steel wheels with alloy

sidewall.

wheel nuts, e.g. when changing to

Use of unsuitable tyres or wheels

winter tyres, the wheel covers cannot

If there is more wear at the front than

may lead to accidents and will

be attached to the steel wheels.

the rear, swap round front wheels and

invalidate the vehicle type

rear wheels. Ensure that the direction

approval.

of rotation of the wheels is the same

Tyre chains

as before.

Wheel covers

Tyres age, even if they are not used.

Wheel covers and tyres that are

We recommend tyre replacement

factory-approved for the respective

every six years.

vehicle and comply with all of the

relevant wheel and tyre combination

Changing tyre and wheel

requirements must be used.

size

If the wheel covers and tyres used are

If tyres of a different size than those

not factory-approved, the tyres must

fitted at the factory are used, it may be

not have a rim protection ridge.

necessary to reprogramme the

Wheel covers must not impair brake

speedometer as well as the nominal

cooling.

tyre pressure and make other vehicle

modifications.

Use tyre chains only on front wheels.

9 Warning

After converting to a different tyre

size, have the label with tyre

Use of unsuitable tyres or wheel

9 Warning

pressures replaced.

covers could lead to sudden

Damage may lead to tyre blowout.

pressure loss and thereby

accidents.

Tyre chains are permitted on tyres of

size 215/65 R16, 215/60 R17 and

215/55 R18.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

202

Vehicle care

On tyres of size 215/65 R16 and

9 Warning

215/60 R17 always use fine mesh

chains suitable for sport utility

Do not drive faster than 50 mph.

vehicles that add no more than

9 mm to the tyre tread and the inboard

Do not use for a lengthy period.

sides (including chain lock).

Steering and handling may be

On tyres of size 215/55 R18 only use

affected.

special snow chains which are

permitted for Vauxhall Mokka and

If you have a flat tyre:

tyres of these sizes. For further

Apply the parking brake and engage

information contact a workshop.

first gear, reverse gear or P.

The use of tyre chains is not permitted

on the temporary spare wheel.

1. Take the tyre repair kit from the

compartment.

Tyre repair kit

2. Remove the compressor.

Minor damage to the tyre tread can be

repaired with the tyre repair kit.

Do not remove foreign bodies from

the tyres.

Tyre damage exceeding 4 mm or that

is at tyre's sidewall cannot be repaired

with the tyre repair kit.

The tyre repair kit is located in the

right side of rear compartment.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

203

3. Remove the electrical connection

cable (1) and air hose (2) from the

stowage compartments on the

underside of the compressor.

6. Unscrew valve cap from defective

10. Set the rocker switch on the

tyre.

compressor to I. The tyre is filled

with sealant.

7. Screw the filler hose to the tyre

valve.

11. The compressor pressure gauge

4. Screw the compressor air hose to

briefly indicates up to 6 bar whilst

8. The switch on the compressor

the connection on the sealant

the sealant bottle is emptying

must be set to J.

bottle.

(approx. 30 seconds). Then the

9. Connect the compressor plug to

pressure starts to drop.

5. Fit the sealant bottle into the

the power outlet or cigarette

retainer on the compressor.

12. All of the sealant is pumped into

lighter socket.

the tyre. Then the tyre is inflated.

Set the compressor near the tyre

To avoid discharging the battery,

in such a way that the sealant

13. The prescribed tyre pressure

we recommend running the

bottle is upright.

should be obtained within

engine.

ten minutes. Tyre pressure

3 230. When the correct pressure

is obtained, switch off the

compressor.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

204

Vehicle care

14. Detach the tyre repair kit. Push

catch on bracket to remove

sealant bottle from bracket. Screw

the tyre inflation hose to the free

connection of the sealant bottle.

This prevents sealant from

escaping. Stow tyre repair kit in

load compartment.

15. Remove any excess sealant

using a cloth.

16. Take the label indicating

maximum permitted speed from

If the prescribed tyre pressure is

If tyre pressure is more than

the sealant bottle and affix in the

not obtained within ten minutes,

1.3 bar, set it to the correct value.

driver's field of view.

remove the tyre repair kit. Move

Repeat the procedure until there

the vehicle one tyre rotation.

17. Continue driving immediately so

is no more loss of pressure.

Reattach the tyre repair kit and

that sealant is evenly distributed

If the tyre pressure has fallen

continue the filling procedure for

in the tyre. After driving approx.

below 1.3 bar, the vehicle must

10 minutes. If the prescribed tyre

6 miles (but no more than

not be used. Seek the assistance

pressure is still not obtained, the

ten minutes), stop and check tyre

of a workshop.

tyre is too badly damaged. Seek

pressure. Screw compressor air

18. Stow away tyre repair kit in load

the assistance of a workshop.

hose directly onto tyre valve and

compartment.

compressor when doing this.

Drain excess tyre pressure with

the button over the pressure

indicator.

Do not run the compressor longer

than 10 minutes.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

205

Notice

● No people or animals may be in

Wheel changing

The driving characteristics of the

the vehicle when it is jacked-up.

Some vehicles are equipped with a

repaired tyre are severely affected,

● Never crawl under a jacked-up

tyre repair kit instead of a spare wheel

therefore have this tyre replaced.

vehicle.

3 202.

If unusual noise is heard or the

● Do not start the vehicle when it is

Make the following preparations and

compressor becomes hot, turn

raised on the jack.

observe the following information:

compressor off for at least

● Clean wheel nuts and thread with

30 minutes.

●

Park the vehicle on a level, firm

a clean cloth before mounting the

and non-skid surface. The front

The built-in safety valve opens at a

wheel.

wheels must be in the straight-

pressure of 102 psi.

ahead position.

Note the expiry date of the kit. After

9 Warning

●

Apply the parking brake and

this date its sealing capability is no

engage first gear, reverse gear or

longer guaranteed. Pay attention to

Do not grease wheel bolt, wheel

storage information on sealant

nut and wheel nut cone.

bottle.

●

Remove the spare wheel 3 207.

1. Disengage wheel nut caps with a

Replace the used sealant bottle.

●

Never change more than one

screwdriver and remove. Pull off

Dispose of the bottle as prescribed

wheel at a time.

the wheel cover.

by applicable laws.

●

Use the jack only to change

The compressor and sealant can be

wheels in case of puncture, not

used from approx. -30 °C.

for seasonal winter or summer

tyre change.

The adapters supplied can be used

to pump up other items e.g.

●

The jack is maintenance-free.

footballs, air mattresses, inflatable

●

If the ground on which the vehicle

dinghies etc. They are located on the

is standing is soft, a solid board

underside of the compressor. To

(max. 1 cm thick) should be

remove, screw on compressor air

placed under the jack.

hose and withdraw adapter.

●

Take heavy objects out of the

vehicle before jacking up.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

206

Vehicle care

3. Ensure the jack is correctly

7. Screw on the wheel nuts.

positioned under the relevant

8. Lower the vehicle and remove

vehicle jacking point.

jack.

Depending on the equipment, first

9. Install the wheel wrench ensuring

remove the covers from the

that it locates securely and tighten

jacking points.

each nut in a crosswise

4. Set the jack to the necessary

sequence. Tightening torque is

height. Position it directly below

140 Nm.

the jacking point in a manner that

10. Align the valve hole in the wheel

prevents it from slipping.

cover with the tyre valve before

installing.

Install wheel nut caps.

2. Fold out the wheel wrench and

install ensuring that it locates

Install centre cap on alloy wheels.

securely and loosen each wheel

11. Install vehicle jacking point cover

nut by half a turn.

on versions with sill panelling.

12. Stow the replaced wheel 3 207

and the vehicle tools 3 194.

13. Check the tyre pressure of the

installed tyre and the wheel nut

torque as soon as possible.

Attach wheel wrench and with the

Have the defective tyre renewed or

jack correctly aligned rotate wheel

repaired as soon as possible.

wrench until wheel is clear of the

ground.

5. Unscrew the wheel nuts.

6. Change the wheel. Spare wheel

3 207.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle care

207

Jacking position for lifting platform

Front arm position of the lifting

platform at the underbody.

Spare wheel

Some vehicles are equipped with a

tyre repair kit instead of a spare wheel

3 202.

If mounting a spare wheel, which is

different from the other wheels, this

wheel might be classified as a

temporary spare wheel and the

corresponding speed limits apply,

The spare wheel is located in the load

even though no label indicates this.

compartment beneath the floor

Rear arm position of the lifting

Seek the assistance of a workshop to

covering. It is secured with a wing nut.

platform centrically under the recess

check the applicable speed limit.

of the sill.

The spare wheel has a steel rim.

Stowing a damaged full size

wheel in the load compartment

Caution

The spare wheel well is not designed

for other tyre sizes than the spare

The use of a spare wheel that is

wheel.

smaller than the other wheels or in

combination with winter tyres

could affect driveability. Have the

defective tyre replaced as soon as

possible.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

208

Vehicle care

Temporary spare wheel

Caution

The use of the temporary spare

wheel could affect driveability.

Have the defective tyre renewed

or repaired as soon as possible.

Only mount one temporary spare

wheel. Do not drive faster than

50 mph. Take curves slowly. Do not

A damaged full size wheel must be

4. Insert the strap through the

use for a long period of time.

stowed in the load compartment and

spokes of the wheel as shown in

If your vehicle gets a flat tyre on the

secured with a strap. Vehicle tools

the illustration.

rear while towing another vehicle,

3 194.

5. Mount the hook to the opposite

mount the temporary spare wheel at

To secure the wheel:

lashing eye.

the front and the full size tyre at the

rear.

1. Position the wheel in the middle of

6. Tighten the strap and secure it

the load compartment.

using the buckle.

Tyre chains 3 201.

2. Place the loop end of the strap

Spare wheel with directional tyre

9 Danger

through the lashing eye on one

side.

If possible, fit directional tyres such

Always drive with folded up and

that they roll in the direction of travel.

3. Place the hook end of the strap

engaged rear seat backrests when

The rolling direction is indicated by a

through the loop and pull it until

stowing a damaged full size wheel

symbol (e.g. an arrow) on the

the strap is fastened securely to

in the load compartment.

sidewall.

the lashing eye.

Vauxhall Mokka X (2016 year). Manual - part 12