Vauxhall Signum (2007 year). Manual - part 7
Instruments, controls
103
p
y
m
Electro-hydraulic power assisted steering
Seat occupancy recognition 3
Cruise control 3
Control indicator lights up red
Symbol is lit, or flashes in the kilometre
Control indicator lights green.
display.
Fault in electro-hydraulic power assisted
It is illuminated when the system is on - see
steering system. The power assisted
Illuminates
page 200.
steering may have failed. The vehicle can
Seat occupancy recognition has detected
be steered but considerably more force is
a child restraint system with transponders.
Y
required. Contact a workshop for
Airbag systems for the front seat
Fuel level
assistance.
passenger are deactivated, see page 87.
Control indicator lights or flashes yellow.
If it flashes
Illuminates
v
Fault in the system or child seats with
Low fuel level, fuel gauge in reserve area.
Electronic Stability Program (ESP®Plus) 3
transponder fitted incorrectly, see page 87.
Control indicator flashes or lights yellow.
Flashing
Fuel supply exhausted, refuel immediately.
Flashing during driving
S
System actively engaged, see page 196.
Engine oil level 3
Never let the tank run dry!
Control indicator lights up yellow.
Illuminates while driving
Erratic fuel supply can cause catalytic
System switched off or fault in the
The engine oil level is checked
converter to overheat - see page 190.
electronic stability program system - see
automatically.
Diesel engines: If the tank is run dry, bleed
page 196.
the fuel system as described on page 226.
Illuminates when the engine is running
Engine oil level too low. Check engine oil
level and top up engine oil if necessary -
see page 268.
104
Instruments, controls
B
Adaptive Forward Lighting 3 (AFL)
Control indicator flashes yellow.
Flashing
Fault in system. Contact a workshop for
help.
Flashing for 4 seconds when the ignition is
switched on
System adjusted for driving abroad.
AFL - see page 132.
Z
w
Exhaust gases 3
Tyre pressure monitoring system 3
Control indicator lights or flashes yellow.
Control indicator lights up red
Tyre pressure difference, check tyre
It illuminates when the ignition is switched
pressure at next opportunity.
on and goes out shortly after the engine
starts.
Control indicator flashes red
Considerable pressure difference or direct
Illuminates when the engine is running
loss of pressure, stop immediately and
Fault in emission control system. The
check tyres and tyre pressure.
permitted emissions may be exceeded.
Contact a workshop immediately.
Control indicator lights up yellow
Fault in system. Contact a workshop for
If it flashes when the engine is running
help.
Fault that may cause damage to the
catalytic converter - see page 192. Contact
Tyre pressure monitoring system - see
a workshop for assistance immediately.
page 204.
Instruments, controls
105
Odometer
Records the miles driven.
Display in the event of airbag system
malfunction - see page 86.
Trip odometer
Display of miles covered since reset.
To set to zero, hold reset knob down for
approx. 2 seconds with ignition switched
on.
Instrument display
Speedometer
Indicates the vehicle speed.
Tachometer
Indicates engine speed.
Warning zone: Maximum permissible
engine speed exceeded; danger to engine.
106
Instruments, controls
For physical reasons, the engine
temperature gauge shows the coolant
temperature only if the coolant level is
adequate.
During operation the system is pressurised.
The temperature may therefore rise briefly
to over 100 °C.
Coolant temperature display
Fuel gauge
Pointer in zone at
= Engine operating
Pointer in
= Reserve area
left
temperature not
left zone or
yet reached
Y illuminated
Pointer in
= Refuelling, see
Pointer between
= Normal operating
left zone or
page 189
the zones
temperature
Y flashing
Pointer in
= Temperature too
Never run the tank dry!
warning zone at
high: Stop. Switch
Diesel engines: If the tank is run dry, bleed
right or W is
off engine. Risk of
the fuel system as described on page 226.
illuminated
engine damage.
Check coolant level
Because of the fuel remaining in the tank,
immediately, see
the amount of fuel required to fill the tank
page 271.
may be less than the specified tank
capacity.
Instruments, controls
107
For Easytronic 3, the display flashes for a
few seconds if A, M or R is selected when
the engine is running but the foot brake is
not depressed.
Transmission display 3
InSP Service interval display 3
Display of gear selected for automatic
When InSP appears in the odometer
transmission 3 or current gear or mode for
display, make an appointment with a
Easytronic 3.
workshop for servicing as soon as possible.
We recommend your Vauxhall Authorised
P
Automatic transmission park
Repairer.
position
Maintenance, inspection system - see
R
Reverse gear
page 266.
N
Neutral
A
Automatic mode on Easytronic
M
Manual mode on Easytronic
D
Automatic mode on automatic
transmission
1-5
Manual mode, current gear on
Easytronic
1-5 Manual mode, selected gear on
1-6 3 automatic
108
Instruments, controls
Ü
Board Computer
19,5°
19:36
11:25}
21.5°C
BC 1
All values
12:01
17,0°C
BC 2
257.0 miles
FM 3
90,6MHz
Range
Timer
1
REG
AS
RDS
TP
Ø
40 mph
RDS
[TP]
11.0 gal
257miles
8
Ø 17.0 miles/gal
Information display
Board information display 3
Graphical information display 3,
Display of time, outside temperature and
colour information display 3
Triple information display
date/infotainment system 3 (when it is on).
Display of time, outside temperature, date/
Display of time, outside temperature and
infotainment system 3 (when it is on) and
date/infotainment system 3 (when it is on).
Display F in the display indicates a fault.
climate control system 3.
Have the cause eliminated by a workshop.
When the ignition is off, the time, date
The graphical information display presents
and outside temperature can be presented
the information in monochrome. The colour
for 15 seconds by briefly pressing one of
information display presents the
the two buttons below the display.
information in colour.
Display F in the display indicates a fault.
Have the cause eliminated by a workshop.
Instruments, controls
109
The type of information and how it is
displayed depends on the equipment
of the vehicle and the Infotainment
system 3, trip computer 3 and climate
control system 3 settings.
8:56
-5,5°C:
Some information appears in the display in
an abbreviated form.
Slippery road
07.04.2004
For Infotainment system see Infotainment
-2,5°C
system instructions. For climate control
system see page 156.
Display F in the display indicates a fault.
OK
Have the cause eliminated by a workshop.
Outside temperature
In vehicles with graphical information
display 3 or colour information display 3,
A fall in temperature is indicated
an icy road surface warning message
immediately and a rise in temperature
appears in the display. No message is
after a time delay.
displayed if the temperature is less
If outside temperature drops to 3 °C, the
than -5 °C.
symbol : illuminates in the triple
information display or the board
9 Warning
information display 3 as a warning for icy
road surfaces. : remains illuminated until
Caution: The road surface may already
temperatures reach at least 5 °C.
be icy even though the display indicates
a few degrees above 0 °C.
110
Instruments, controls
Correcting time 3
Deactivating/activating automatic time
Some RDS transmitters do not send a
synchronisation: infotainment system off,
correct time signal. If the incorrect time is
press Ö and ; below the display:
continually displayed, deactivate
8:56
5,5°C
Hold down Ö for approx. 2 sec., clock
automatic time synchronisation 3, see next
display is now in setting mode.
column, and set the time manually.
07.04.2004
Press Ö twice (until year flashes).
The automatic setting is indicated by } in
the display.
Press Ö and hold down for approx.
3 seconds until } flashes in display 3
and text "RDS TIME" appears
(years flash during this time).
Press ;; display shows:
RDS TIME 0 = Off
Press ;; display shows:
Triple information display
RDS TIME 1 = On
Set date and time
Press Ö three times.
Infotainment system off: press Ö and ;
below the display as follows:
Press Ö for approx. 2 seconds:
Day flashes
;: Set day
Ö: Month flashes
;: Set month
Ö: Year flashes
;: Set year
Ö: Hours flash
;: Set hours
Ö: Minutes flash
;: Set minutes
Ö: Clock is started.
Instruments, controls
111
11:25}
21.5°C
Range
257miles
Board information display 3,
To select with four-way button:
To select using the left adjuster wheel 3
Select options via the menus and with the
on the steering wheel
selecting functions
buttons/four-way button on the
Push upwards
Functions and settings of some
infotainment system 3.
Previous menu item.
equipment 3 can be accessed via the
board information display.
Push downwards
Next menu item.
This is done using the menus and the
buttons/four-way button on the
Press
Infotainment system 3 or the left-hand
Selection of marking, confirmation of
adjuster wheel 3 on the steering wheel.
commands.
The respective menu options are then
System settings - see page 112.
shown in the following lines on the display.
Trip computer 3 - see page 114.
If Check Control warning messages 3 are
displayed, the display is blocked to other
displays. Confirm the warning message. If
there are several warning messages,
confirm one after the other.
112
Instruments, controls
The functions are displayed in the following
order:
z Time synchronisation
z Time, setting hours
11:25}
21.5°C
z Time, setting minutes
11:25}
21.5°C
z Date, setting day
z Date, setting month
System
Clock Sync.On
z Date, setting year
z Ignition logic
z Language selection
z Setting units of measure
Board information display 3,
Correcting time 3
Some RDS transmitters do not send a
system settings
correct time signal. If the incorrect time is
Press the Settings button of the
continually displayed, deactivate
infotainment system. Menu item Audio
automatic time synchronisation 3 and set
or System will appear.
the time manually - see next page.
Press the lower button of the four-way
button to reach menu item System. After
pressing the right-hand part of the four-
way button, the first function of the System
menu is shown.
Some information appears in the display in
an abbreviated form.
Instruments, controls
113
The automatic setting is indicated by } in
the display.
To correct time with the help of RDS, select
the menu item for time synchronisation
from the Settings menu.
11:25}
21.5°C
11:25}
21.5°C
Make the desired setting.
Setting date and time
Deutsch
Unit Europe-SI
Select the menu item for time and date
setting from the Settings menu.
Make the desired setting.
The setting is executed upon exit from the
menu item.
Ignition logic 3
Language selection
Setting units of measure
Adjustment, see infotainment system
You can select the display language for
You can select which units of measure are
instructions.
some functions.
to be used.
Select the menu item for language from
Select the menu item for units of measure
the Settings menu and make the desired
from the Settings menu and make the
setting.
desired setting.
114
Instruments, controls
Board information display 3,
Average consumption
trip computer 3
Average consumption display.
Measurement may be reset to zero at any
The trip computer provides information on
time and restarted, see "Resetting the trip
driving data, which is continually recorded
computer information".
and evaluated electronically.
11:25}
21.5°C
Effective consumption
Access trip computer vehicle data by
Fuel consumption display. Measurement
pressing the BC button on the infotainment
Inst. Consumpt.
may be reset to zero at any time and
system or the left adjuster wheel 3 on the
restarted, see "Resetting the trip computer
steering wheel.
information".
Some information appears in the display in
17.6miles/gal
Average speed
an abbreviated form.
Average speed display. Measurement may
Once an audio function has been selected,
be reset to zero at any time and restarted,
the subsequent rows of the trip computer
see "Resetting the trip computer
function are displayed.
Instantaneous consumption
information".
Display changes depending on speed:
The functions are displayed in the following
Stoppages in the journey with the ignition
order:
Display in gal/h below 8 mph (13 km/h),
off are not included in the calculations.
z Instantaneous consumption
Display in mpg above 8 mph (13 km/h).
Distance travelled
z Average consumption
Distance travelled display. Measurement
z Effective consumption
may be reset to zero at any time and
z Average speed
restarted, see "Resetting the trip computer
z Distance travelled
information".
z Range
z Stop watch
Instruments, controls
115
Resetting trip computer information
The following trip computer information
can be reset (reset to zero and
measurements/calculations restarted):
11:25}
21.5°C
z Average consumption
11:25}
21.5°C
z Effective consumption
z Average speed
Range
Stop Watch
z Distance travelled.
Select the desired trip computer
information.
257miles
01:22:32h
Reset using the left wheel on the steering
wheel or the right/left button of the four-
way button:
Range
z Press for more than 2 seconds: Current
Stop watch
Range is calculated from current fuel tank
value.
Operation with the four-way button:
content and instantaneous consumption.
z Press for more than 4 seconds: All values.
z Press right button: Start/Stop.
The display shows average values.
z Press left button for more
After refuelling, the vehicle updates the
than 2 seconds: Reset.
range automatically after a brief delay.
Operating using the left adjuster wheel 3
If less than 30 miles (50 km) can be driven
on the steering wheel:
with the fuel remaining in the tank, the
warning "Range" appears on the display.
z Press: Start/Stop.
If less than 20 miles (30 km) can be driven
Interruption of power supply
with the fuel remaining in the tank, the
If the power supply has been interrupted or
warning "Refuel!" 3 appears on the
if the battery voltage has dropped too low,
display.
the values stored in the trip computer will
be lost.
Acknowledge the menu item as described
on page 111.
116
Instruments, controls
FM
[TP]
CDin
90.6 MHz
19,5°
19:36
Graphical information display 3
To select with four-way button
To select using the multifunction button
Select menu items via menus and with the
Turn
or colour information display 3,
buttons/four-way button of the
Marking of menu options or commands,
selecting functions
infotainment system.
selection of function ranges,
The functions and settings of some
equipment 3 can be accessed via the
Press
graphical information display or the colour
Selection of marking, confirmation of
information display.
commands.
Functions are selected and executed in the
To exit a menu, turn the multifunction
menu on the display using the four-way
button left or right to Return or Main and
button, the multifunction button 3 on the
select.
infotainment system or the left wheel 3 on
the steering wheel.
If Check Control warning messages 3 are
displayed, the display is blocked to other
displays. Confirm the warning message. If
there are several warning messages,
confirm one after the other.
Instruments, controls
117
7 Settings
19,5°
19:36
FM
[TP]
CDin
Time, Date
19:36
Language
90.6 MHz
Units
10 . 07 . 2004
Contrast
Day / Night
19,5°
19:36
6 Ign. logic
To select using the left adjuster wheel 3
Function ranges
System settings
on the steering wheel
For each functional area there is a main
The settings are accessed via the Settings
Push upwards
page (Main), which is selected at the top
menu.
Previous menu item.
edge of the display (not with the
Press the Main button 3 (not found on all
Infotainment system CD 30 or the Mobile
Push downwards
infotainment systems) on the infotainment
Phone Portal):
Next menu item.
system (call up main display).
z Audio
Press
Press the Settings button of the
z Navigation 3
Selection of marking, confirmation of
infotainment system. No menu may be
z Telephone 3
commands.
selected with Infotainment System CD 30.
z Trip computer 3.
The Settings menu is displayed.
For audio, navigation 3 and telephone
functions 3, see infotainment system
instructions.
118
Instruments, controls
Correcting time 3
For systems with GPS receiver1), time and
date are automatically set upon receipt of
7 Time, Date
19,5°
19:36
a GPS satellite signal. If the displayed time
7 Settings
19,5°
19:36
does not correspond to local time, time can
Time
19:36
Time, Date
be manually corrected in 30-minute
increments or automatically corrected via
Language
Deutsch
receipt of an RDS time signal2) 3.
Units
English
Date
10 . 07 . 2004
Some RDS transmitters do not send correct
Contrast
Español
time signals. If the incorrect time is
Day / Night
Nederlands
6 Synchron. clock automatical.
displayed often, deactivate automatic
time synchronisation 3 and set the time
6 Ign. logic
Français
manually.
To correct time with the help of RDS, select
Setting the date and time 3
menu item Synchron. clock automatical.
Language selection
Select menu item Time, Date from
You can select the display language for
from the Time, Date menu.
the Settings menu.
some functions.
The box in front of Synchron. clock
The menu for Time, Date is displayed.
automatical. will be ticked;
Select menu item Language from the
see Fig. 17340 T.
Settings menu.
Select the menu items required:
The available languages are displayed.
Make the desired setting.
1) GPS = Global Positioning System, satellite
system for world-wide positioning.
2) RDS = Radio Data System.
Instruments, controls
119
7 13 Languages
19,5°
19:36
7 Settings
19,5°
19:36
7 Contrast
19,5°
19:36
X Deutsch
Time, Date
English
Language
~ Europe-SI
Español
Units
|
Japan
12
Nederlands
Contrast
|
Great Britain
Français
Day / Night
|
USA
Italiano
6 Ign. logic
Select the desired language.
Setting units of measure
Adjusting contrast 3
You can select which units of measure are
(Graphical information display)
Selections are indicated by a 6 in front of
to be used.
Select menu item Contrast from the
the menu item.
Settings menu.
Select menu item Units from the Settings
In systems with voice output 3, when the
menu.
The menu for Contrast is displayed.
language setting of the display is changed
the system will ask whether the
The available units are displayed.
Confirm the required setting.
announcement language should also be
Select the desired unit.
changed - see Infotainment system
instructions.
Selections are indicated by a o in front of
the menu item.