Pontiac G8 (2008 year). Manual - part 6

 

  Index      Pontiac     Pontiac G8 (2008 year) - manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     4      5      6      7     ..

 

 

Pontiac G8 (2008 year). Manual - part 6

 

 

Speedometer

The speedometer can display your
speed in both miles per hour
(MPH) and kilometers per hour
(km/h). You can select between
MPH and km/h using the UNITS
display in the DIC. See DIC
Operation and Displays on
page 4-23 
for more information.

Tachometer

The tachometer displays the engine
speed in revolutions per minute.

Safety Belt Reminders

Safety Belt Reminder Light

When the engine is started, a chime
will come on for several seconds
to remind people to fasten their
safety belts, unless the driver’s
safety belt is already buckled.

The safety belt light will also come on
and stay on for several seconds,
then it will flash for several more.

This chime and light is repeated if
the driver remains unbuckled
and the vehicle is in motion. If the
driver’s belt is already buckled,
neither the chime nor the light will
come on.

Passenger Safety Belt
Reminder Light

If your vehicle has this light, several
seconds after the engine is
started, a chime will sound for
several seconds to remind the front
passenger to buckle their safety
belt. The passenger safety belt light
will also come on and stay on for
several seconds, then it will flash for
several more.

This chime and light are repeated if
the passenger remains unbuckled
and the vehicle is in motion.

If the passenger’s safety belt is
buckled, neither the chime nor the
light will come on.

4-12

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Airbag Readiness Light

There is an airbag readiness
light which shows the airbag symbol.
The system checks the airbag’s
electrical system for malfunctions.
The light tells you if there is an
electrical problem. The system
check includes the airbag sensor,
the pretensioners, the airbag
modules, the wiring and the crash
sensing and diagnostic module.
For more information on the airbag
system, see Airbag System on
page 1-19
.

This light will come on when you
start your vehicle, and it will flash for
a few seconds. The light should
go out and the system is ready.

If the airbag readiness light and the
Airbag Fault message on the
Driver Information Center (DIC)
stays on after you start the vehicle
or comes on when you are
driving, your airbag system may not
work properly. Have your vehicle
serviced right away.

{

CAUTION

If the airbag readiness light
stays on after you start your
vehicle, it means the airbag
system may not be working
properly. The airbags in your
vehicle may not inflate in a
crash, or they could even
inflate without a crash. To help
avoid injury to yourself or
others, have your vehicle
serviced right away.

The airbag readiness light should
flash for a few seconds when
you start the vehicle. If the light does
not come on then, have it fixed
immediately. If there is a problem
with the airbag system, a message
may also come on. See DIC
Warnings and Messages on
page 4-27 
for more information.

The message will remain until

3

or

8

are pressed, but the light

will remain until the problem is fixed.
See DIC Warnings and Messages
on page 4-27 
for more information.

Instruments and Controls

4-13

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Passenger Airbag Status
Indicator

The vehicle has a passenger
sensing system. The rearview mirror
has a passenger airbag status
indicator.

When the vehicle is started, the
passenger airbag status indicator
will light ON and OFF, or the symbol
for on and off, for several seconds
as a system check. If you are
using remote start to start your
vehicle from a distance, if equipped,
you may not see the system
check. Then, after several more
seconds, the status indicator
will light either ON or OFF, or either
the on or off symbol to let you
know the status of the right front
passenger frontal airbag.

If the word ON or the on symbol is
lit on the passenger airbag status
indicator, it means that the right front
passenger frontal airbag is enabled
(may inflate).

{

CAUTION

If the on indicator comes on
when you have a rear-facing
child restraint installed in the
right front passenger’s seat, it
means that the passenger
sensing system has not turned
off the passenger’s frontal
airbag. A child in a rear-facing
child restraint can be seriously
injured or killed if the right
front passenger’s airbag
inflates. This is because the
back of the rear-facing child
restraint would be very close to
the inflating airbag. Do not use
a rear-facing child restraint in
the right front passenger’s seat
if the airbag is turned on.

United States

Canada

4-14

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

{

CAUTION

Even though the passenger
sensing system is designed to
turn off the right front
passenger’s frontal airbag if the
system detects a rear-facing
child restraint, no system is
fail-safe, and no one can
guarantee that an airbag will
not deploy under some unusual
circumstance, even though it is
turned off. We recommend that
rear-facing child restraints be
secured in the rear seat, even if
the airbag is off.

If the word OFF or the off symbol is
lit on the passenger airbag status
indicator, it means that the
passenger sensing system has
turned off the right front passenger
frontal airbag. See Passenger
Sensing System on page 1-26 
for
more information, including
important safety information.

If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system. See
your dealer/retailer for service.

{

CAUTION

If the airbag readiness light in
the instrument panel cluster
ever comes on and stays on, it
means that something may be
wrong with the airbag system.
If this ever happens, have the
vehicle serviced promptly,
because an adult-size person
sitting in the right front
passenger’s seat may not have
the protection of the airbag(s).
See Airbag Readiness Light on
page 4-13 
for more on this,
including important safety
information.

Voltmeter Gage

The voltmeter shows the voltage
output of your battery.

It is located in the center of the
instrument panel.

Charging System Light

This light will come on briefly when
you turn on the ignition, and the
engine is not running, as a check to
show it is working. Then it should
go out when the engine is started.

If the light comes on and an
Alternator message on the Driver
Information Center (DIC) stays
on, you may have a problem with
the electrical charging system. Have
it checked by your dealer/retailer.

Instruments and Controls

4-15

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving while this light is on could
drain your battery.

If you must drive a short distance
with the light on, be sure to turn off
all accessories, such as the radio
and air conditioner.

The Alternator message will remain
until

3

(Trip/Fuel) or

8

(Enter)

are pressed, but the light will remain
until the problem is fixed. See
DIC Warnings and Messages on
page 4-27 
for more information.

Brake System Warning
Light

Your vehicle’s hydraulic brake
system is divided into two parts. If
one part is not working, the
other part can still work and stop
you. For good braking, though, you
need both parts working well.

If the warning light comes on, there
is a brake problem. Have your
brake system inspected right away.

If your vehicle has anti-lock brakes,
this light should come on when
you turn the key to START. If it does
not come on, have it fixed so it
will be ready to warn you if there is
a problem.

When the ignition is on, the brake
system warning light will also
come on when you set your parking
brake. The light will stay on if
your parking brake does not release
fully. If it stays on after your
parking brake is fully released, it
means you have a brake problem.

If the light comes on and Brake
message comes on the Driver
Information Center (DIC), while you
are driving, pull off the road and
stop carefully. You may notice that
the pedal is harder to push or
the pedal may go closer to the floor.

It may take longer to stop. If the
light is still on, have the vehicle
towed for service. See Antilock
Brake System (ABS) Warning Light
on page 4-17 
and Towing Your
Vehicle on page 9-84
.

{

CAUTION

Your brake system may not be
working properly if the brake
system warning light is on.
Driving with the brake system
warning light on can lead to an
accident. If the light is still on
after you have pulled off the
road and stopped carefully,
have the vehicle towed for
service.

The Brake message will remain until

3

(Trip/Fuel) or

8

(Enter) are

pressed, but the brake light will
remain until the problem is fixed. See
DIC Warnings and Messages on
page 4-27 
for more information.

United States

Canada

4-16

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Antilock Brake System
(ABS) Warning Light

For vehicles with the Antilock Brake
System (ABS), this light will come
on briefly, as a check, when
you start your vehicle.

If it does not, have your vehicle
serviced so that the light works
properly when it needs to.

If the light and a message in the
DIC stays on longer than a few
seconds after you start your engine,
or comes on and stays on while
you are driving, try resetting
the system. To reset the system:

1. If you are driving, pull over when

it is safe to do so.

2. Place the vehicle in PARK (P).

3. Turn off the ignition.

4. Then restart the engine.

If the light remains on after resetting
the system or comes on again
while driving, your vehicle needs
service. If the ABS light is on,
but the regular brake system
warning light is not on, the antilock
brakes are not working properly,
but the regular brakes are still
functioning. Have your vehicle
serviced right away. If both brake
lights are on, you do not have
antilock brakes, and there’s a
problem with your regular brakes as
well. Have your vehicle towed for
service. See Towing Your Vehicle
on page 9-84
.

The ABS Fault message will remain
until

3

(Trip/Fuel) or

8

(Enter)

are pressed, but the warning
light will remain until the problem is
fixed. See DIC Warnings and
Messages on page 4-27 
for more
information.

Engine Coolant
Temperature Gage

This gage shows the engine coolant
temperature. If the gage pointer
moves into the red area, the engine
is too hot. It means that the engine
has overheated. Pull off the road,
stop the vehicle, and turn off the
engine as soon as possible. See
Engine Overheating on page 9-16.

Instruments and Controls

4-17

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Tire Pressure Light

TPMS Light

This light comes on briefly when the
engine is started and provides
information about tire pressures and
the Tire Pressure Monitoring System.

When the Light is Solid

This light will also come on when
one or more of your tires are
significantly underinflated. A CHECK
TIRE PRESSURE DIC message
will accompany the light.

See DIC Warnings and Messages
on page 4-27 
for more information.

Stop and check your tires as soon as
it is safe to do so. If underinflated,
inflate to the proper pressure. See
Tires on page 9-39 for more
information.

When the Light Flashes First and
Then is Solid

This indicates that there may be a
problem with the Tire Pressure
Monitor System.

The light flashes for about a minute
and stays on solid for the
remainder of the ignition cycle. This
sequence will repeat with every
ignition cycle. See Tire Pressure
Monitor System on page 9-49
and Tire Pressure Monitor Operation
on page 9-51 
for more information.

Malfunction
Indicator Lamp

Check Engine Light

A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It makes sure that
emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.

This light comes on briefly, as a
check to show it is working,
when the ignition is turned to
ON/RUN. If the light does not come
on, see your dealer/retailer.

If the light stays on it indicates that
there is an OBD II problem and
service is required.

4-18

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Malfunctions often are indicated by
the system before any problem
is apparent. Heeding the light can
prevent more serious damage
to your vehicle. This system assists
your service technician in correctly
diagnosing any malfunction.

Notice: If you keep driving your
vehicle with this light on, after
a while, the emission controls
might not work as well, your
vehicle’s fuel economy might not
be as good, and the engine
might not run as smoothly. This
could lead to costly repairs
that might not be covered by your
warranty.

Notice: Modifications made to
the engine, transmission, exhaust,
intake, or fuel system of your
vehicle or the replacement of the
original tires with other than those
of the same Tire Performance
Criteria (TPC) can affect your
vehicle’s emission controls and
can cause this light to come on.
Modifications to these systems

could lead to costly repairs not
covered by your warranty. This
could also result in a failure to
pass a required Emission
Inspection/Maintenance test.
See Accessories and
Modifications on page 9-3
.

This light comes on during a
malfunction in one of two ways:

Light Flashing: A misfire condition
has been detected. A misfire
increases vehicle emissions and
could damage the emission control
system on your vehicle. Diagnosis
and service might be required.

The following can prevent more
serious damage to your vehicle:

Reduce vehicle speed.

Avoid hard accelerations.

Avoid steep uphill grades.

If you are towing a trailer, reduce
the amount of cargo being
hauled as soon as it is possible.

If the light continues to flash, when
it is safe to do so, stop the
vehicle. Find a safe place to park
the vehicle. Turn the key off, wait at
least 10 seconds, and restart the
engine. If the light is still flashing,
follow the previous steps and
see your dealer/retailer for service
as soon as possible.

Light On Steady: An emission
control system malfunction has been
detected on your vehicle. Diagnosis
and service might be required.

You might be able to correct the
emission system malfunction
by considering the following:

Make sure the fuel cap is fully
installed. See Filling the Tank
on page 8-35
. The diagnostic
system can determine if the fuel
cap has been left off or
improperly installed. A loose or
missing fuel cap allows fuel
to evaporate into the atmosphere.
A few driving trips with the cap
properly installed should turn
the light off.

Instruments and Controls

4-19

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

If you just drove through a deep
puddle of water, your vehicle’s
electrical system might be
wet. The condition is usually
corrected when the electrical
system dries out. A few driving
trips should turn the light off.

If you recently changed brands of
fuel, be sure to fuel your vehicle
with quality fuel. See Gasoline
Octane on page 8-33
. Poor
fuel quality causes the engine
not to run as efficiently as
designed. You might notice this
as stalling after start-up,
stalling when you put the vehicle
into gear, misfiring, hesitation
on acceleration, or stumbling on
acceleration — these conditions
might go away once the
engine is warmed up.

If you experience one or more of
these conditions, change the
fuel brand you use. It will require
at least one full tank of the
proper fuel to turn the light off.

If none of the above have made
the light turn off, your dealer/retailer
can check the vehicle. Your
dealer/retailer has the proper test
equipment and diagnostic tools to
fix any mechanical or electrical
problems that might have
developed.

Emissions Inspection and
Maintenance Programs

Some state/provincial and local
governments have or might begin
programs to inspect the emission
control equipment on your vehicle.
Failure to pass this inspection
could prevent getting a vehicle
registration.

Here are some things to know to
help your vehicle pass an
inspection:

Your vehicle will not pass this
inspection if the check engine
light is on or not working properly.

Your vehicle will not pass
this inspection if the OBD
(on-board diagnostic) system
determines that critical emission
control systems have not
been completely diagnosed by
the system. The vehicle would be
considered not ready for
inspection. This can happen if
you have recently replaced
the battery or if the battery has
run down. The diagnostic system
is designed to evaluate critical
emission control systems
during normal driving. This can
take several days of routine
driving. If you have done this and
your vehicle still does not pass
the inspection for lack of
OBD system readiness, your
dealer/retailer can prepare
the vehicle for inspection.

4-20

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Security Light

For information regarding this light
and the vehicle’s security system,
see Content Theft-Deterrent
on page 2-13
.

Fog Lamp Light

The fog lamp light will come on
when the fog lamps are in use.

The light will go out when the fog
lamps are turned off. See Fog
Lamps on page 5-3 
for more
information.

Highbeam On Light

This light comes on when the
high-beam headlamps are in use.

See Headlamp High/Low-Beam
Changer on page 4-7 
for more
information.

Daytime Running Lamps
(DRL) Indicator Light

This light turns on whenever the
Daytime Running Lamps are on.

See Daytime Running Lamps (DRL)
on page 5-2 
for more information.

Door Ajar Light

When the ignition is on, this light will
stay on until all doors are closed
and completely latched.

If a door is not closed properly, a
chime sounds after the engine
is started and the vehicle is not in
PARK (P).

Instruments and Controls

4-21

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Oil Pressure Gage

The gage shows the engine oil
pressure.

It is located in the center of the
instrument panel.

{

CAUTION

Do not keep driving if the oil
pressure is low. If you do, your
engine can become so hot that
it catches fire. You or others
could be burned. Check your
oil as soon as possible and
have your vehicle serviced.

Notice: Lack of proper engine oil
maintenance may damage the
engine. The repairs would not be
covered by the vehicle warranty.
Always follow the maintenance
schedule in this manual for
changing engine oil.

Fuel Gage

The fuel gage shows about how
much fuel you have left, when the
ignition is on.

When the indicator nears empty, the
low fuel warning light will come
on and along with a chime. There is
still a little fuel left, but you should
refuel soon.

Here are four things that some
owners ask about. These are normal
and do not indicate a problem
with your fuel gage:

At the service station, the gas
pump shuts off before the
gage reads full.

It takes a little more or less fuel
to fill up than the gage indicated.

The indicator moves a little when
you turn a corner or speed up.

The gage will continue to show
the remaining fuel when the
ignition is turned off.

4-22

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driver Information
Center (DIC)

The DIC displays information about
your vehicle. It also displays warning
messages if a system problem is
detected. The DIC also allows some
features to be customized. See DIC
Vehicle Customization on page 4-32
for more information. All messages
will appear in the DIC display located
in the center of the instrument panel
cluster.

When the ignition is turned on, a
vehicle system check is performed
and the status is shown on the
DIC display. If there are no warnings
or service reminders, the display
shows a series of welcome screens.
When the ignition is turned off,
the odometer appears on the display
for a short period of time unless a
service reminder is active. Active
service reminders are displayed for
10 seconds before the odometer
appears. The odometer will
reappear on the display when the
driver door is opened. For more

information on the warnings and
messages see DIC Warnings
and Messages on page 4-27
.

DIC Operation and
Displays

The DIC has different displays
which can be accessed by pressing
the DIC buttons located on the
left side of the steering wheel. The
DIC displays trip, fuel, vehicle
system information, and warning
messages if a system problem
is detected.

DIC Buttons

3

(Trip/Fuel): Press this button

to go through the displays and
the select the information.

Q R

(Thumbwheel): Use the

thumbwheel to scroll through
the available options.

8

(ENTER to Reset/Select): Press

the thumbwheel to set or reset
certain functions and to turn off or
acknowledge messages on the DIC.

Trip/Fuel Menu Items

Press

3

to scroll through the

following menu items:

Speedometer

UNITS

Tire Pressure

Customize Options

Odometer/Trip Odometer

Distance/Time To Go

Range

Avg (Average)Speed/Avg
(Average) Fuel

OverSpeed

Instruments and Controls

4-23

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Speedometer

Press

3

until the speedometer is

displayed.

The speedometer shows how fast
the vehicle is moving in either miles
per hour (MPH) or kilometers per
hour (km/h). To switch between
English and metric measurements,
see “UNITS” later in this section.

The digital speedometer display can
be enabled or disabled. See
“Digital Speedometer” under DIC
Vehicle Customization on page 4-32
for more information.

UNITS

Move the thumbwheel up

Q

or down

R

to highlight English or Metric

when the UNITS display is active.
Press

8

to confirm the setting. This

will change the displays on the
cluster, DIC, and the temperature
display in the mirror to either English
or metric measurements.

Tire Pressure

Press

3

until Tire Pressure is

displayed.

The display will show a vehicle and
the approximate pressures of all
four tires. Tire pressure is displayed
in either pounds per square
inch (PSI) or in kilopascal (kPa).

This display can be customized. See
DIC Vehicle Customization on
page 4-32 
for more information.

Customize Options

See DIC Vehicle Customization on
page 4-32 
for more information.

Odometer/Trip Odometer

Press

3

until the Odometer/Trip

Odometer is displayed.

The odometer display shows the
distance the vehicle has been driven
in either miles (MI) or kilometers
(km). To switch between English
and metric measurements, see
“UNITS” earlier in this section.

The Trip Odometer display shows
the current distance traveled
since the last reset for the trip
odometer. The trip odometer can be
reset to zero by pressing and
holding

8

while the trip odometer

value is highlighted. If

8

is only

pressed briefly, the Avg Speed/Avg
Fuel will be reset as well.

Distance/Time To Go

Press

3

until To Go is displayed.

If this item doesn’t display, check
that the display is turned on through
the Customize Options menu.
See DIC Vehicle Customization on
page 4-32 
for more information.

At the start of a trip, estimate
the distance to arrival (for example,
from maps, road signs). Move
the thumbwheel up or down until the
display shows the estimated trip

4-24

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

distance. When driving, the
computer constantly updates the
time to arrival, based on changing
driving speeds. Use the thumbwheel
to adjust the distance any time
this display is shown. Time to go is
shown in hours and minutes and
is only shown if the distance to go is
more than zero.

This display can be turned on or off
and the default setting can be
changed.

Range

Press

3

until Range is displayed.

This display shows the approximate
distance the vehicle can be
driven without refueling. The fuel
range estimate is based on an
average of the vehicle’s fuel
economy over recent driving history
and the amount of fuel remaining
in the fuel tank. Fuel range cannot
be reset.

Avg (Average)Speed/Avg
(Average) Fuel

Press

3

until Avg Speed/Avg

Fuel is displayed.

Avg Speed shows the average
speed (while the engine is running)
since the last reset.

Avg Fuel shows average fuel used
since the last reset.

To reset only the Avg Speed or Avg
Fuel, press and hold

8

while

either value is highlighted. If

8

is

only pressed briefly, the Trip
Odometer will be reset as well.

OverSpeed

OverSpeed allows the driver to set
a speed that they do not want
to exceed. OverSpeed will illuminate
in the display and a chime will
sound to warn that the vehicle’s
speed is equal or has exceeded the
preselected value. During an
OverSpeed warning, the OverSpeed
display is shown, allowing the
driver to make adjustments.

To set the OverSpeed warning
press

3

when OverSpeed

is displayed to highlight the
OverSpeed mode. Move the
thumbwheel up

Q

or down

R

to

scroll through and highlight one
of the following options:

Off: No OverSpeed warning set.

Manual: Allows you to manually set
the OverSpeed warning. See
“Manual OverSpeed” following.

Preset 1: Default setting 30 MPH
(48 km/h)

Instruments and Controls

4-25

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Preset 2: Default setting 45 MPH
(72 km/h)

Preset 3: Default setting 55 MPH
(89 km/h)

Preset 4: Default setting 70 MPH
(113 km/h)

The selection is set automatically
after a few seconds.

The corresponding value of the
presets will be shown on the display.

The preset OverSpeed warnings
can be reprogrammed. See
“Programming the OverSpeed
Presets” later in this section.

Manual OverSpeed

To manually set the OverSpeed
warning:

1. Use the thumbwheel to select

Manual for OverSpeed.

2. Press

8

to highlight the current

value.

3. Use the thumbwheel to adjust

the value in 5 MPH or km/h
increments and press

8

to confirm the setting.

To set the OverSpeed warning to
the vehicle’s current speed:

1. Use the thumbwheel to select

Manual as described in the
OverSpeed section.

2. Press

8

to highlight the current

value.

3. Press and hold

8

for more than

3 seconds to set the value to
the nearest 5 MPH or km/h
above the current vehicle’s
speed.

Programming the OverSpeed
Presets

While the vehicle’s speed is 6 MPH
(10 km/h) or below, each of the
presets can be altered and values
can be stored for future use.

To reprogram the OverSpeed
presets:

1. Use the thumbwheel to select the

desired preset and press

8

.

2. Move the thumbwheel up

Q

or

down

R

to adjust the value in

1km/h increments.

3. Press

8

to confirm the setting.

Adjusting the Setting During
an OverSpeed Warning

While the OverSpeed warning is
displayed move the thumbwheel up

Q

or down

R

to adjust the

value when in Manual mode or to
select a different preset when
in Preset mode. Press and hold

8

for more than 3 seconds to set
the value to the nearest 5 MPH or
km/h above the current vehicle’s
speed. If Preset mode was selected,
this will change it to Manual mode.

4-26

Instruments and Controls

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Underspeed Chime

If an OverSpeed warning appeared
and the vehicle’s speed drops
below the set value, you will hear a
chime. The underspeed chime
can be turned on or off through the
vehicle customization. See DIC
Vehicle Customization on page 4-32
for more information.

DIC Warnings and
Messages

Messages are displayed on the DIC
to notify the driver that the status
of the vehicle has changed and that
some action may be needed by
the driver to correct the condition.
Multiple messages may appear one
after another.

Some messages may not require
immediate action, but you can press

3

or

8

to acknowledge that

you received the messages and to
clear them from the display.
Some messages cannot be cleared
from the DIC display because

they are more urgent. These
messages require action before they
can be cleared. You should take
any messages that appear on
the display seriously and remember
that clearing the messages will
only make the messages disappear,
not correct the problem.

The following are the possible
messages that can be displayed
and some information about them.

!

ABS Fault

This message is displayed if there is
a problem with the ABS system.
The ABS light may also turn on in
the instrument panel cluster.
See Antilock Brake System (ABS)
Warning Light on page 4-17
.
When this message is on, the brake
system will still operate with the
antilock operation disabled.
See your dealer/retailer.

u

Active Select On

This message is displayed when the
automatic transmission active
select mode is enabled. See “Active
Select Mode” under Automatic
Transmission Operation on
page 8-6
.

9

Airbag Fault

This message is displayed if there is
a problem with the airbag system
or safety belt pretensioner system.

See Airbag System on page 1-19
and “Safety Belt Pretensioners”
under Lap-Shoulder Belt on
page 1-14
. The Airbag Readiness
light may also come on in the
instrument panel cluster. See Airbag
Readiness Light on page 4-13
.
See your dealer/retailer.

Instruments and Controls

4-27

2008 - Pontiac G8 Owner Manual

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     4      5      6      7     ..