Porsche Cayenne (2010 year). Manual - part 20
4. Pull both release tabs on the plug apart, and
3. Press release tab A in direction of arrow again
Changing bulb for turn signal and side
pull plug out of lamp socket.
and push forward. Using your other hand, pull
marker light
the bulb housing completely out of the front
5. Replace defective bulb. Make sure that the
Cayenne, Cayenne S, Cayenne S
apron.
bulb is installed in the correct position.
Transsyberia
6. Fit cover on headlight. Both release tabs must
1. Remove headlight.
be fully engaged.
For information on removing headlights:
Please see the chapter “REMOVING HEAD-
7. Install headlight.
LIGHTS” on Page 327.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
2. Press release tab on the bulb housing in the
LIGHTS” on Page 328.
direction of the arrow and at the same time
push forward to the first detent A.
8. Check operation of bulbs.
Minor Repairs
333
Replacing side marker light bulb
5. Remove the defective bulb from the socket
Changing turn signal bulb
Cayenne, Cayenne S, Cayenne S
and replace.
Cayenne, Cayenne S, Cayenne S
Transsyberia
When inserting the socket in the bulb housing,
Transsyberia
make sure that the socket has engaged fully.
4. Pull bulb socket out of the bulb housing.
1. Turn socket counter-clockwise and remove.
2. Replace the defective bulb (bayonet fitting).
3. Insert socket and turn in clockwise direction.
Make sure that the bulb is installed in the
correct position.
334 Minor Repairs
4. Insert socket and turn in clockwise direction.
Make sure that the bulb is installed in the
correct position.
5. Check operation of bulb.
6. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
Installing bulb housing
Changing bulb for turn signal
Cayenne, Cayenne S, Cayenne S
Cayenne GTS
Transsyberia
1. Remove headlight.
1. Insert the bulb housing in the front apron. Make
For information on removing headlights:
sure that the two tabs are inserted correctly in
Please see the chapter “REMOVING HEAD-
the openings. Push light fully into the front
LIGHTS” on Page 327.
apron until you hear and feel it engage.
2. Turn socket counter-clockwise and remove.
2. Check operation of lights.
3. Replace the defective bulb (bayonet fitting).
3. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
Minor Repairs
335
Tail light
Removing tail light
As a result of the design, a relatively large amount
of effort is required to remove the tail light.
In case of doubt, please contact your authorized
Porsche dealer.
1. Switch ignition off.
4. Unscrew the two fastening screws B with the
socket wrench from the tool kit.
2. Open rear lid.
3. Remove the two caps A with a screwdriver, for
example.
336 Minor Repairs
5. Pull out the light unit to the side in the direc-
Installing tail light
3. Screw in the fastening screws B.
tion of the arrow and additionally pull it out in
When screwing in the fastening screws, make
the area of the ball head C.
1. Push on plug D until the plug is felt to click into
sure that the tail light is flush with the body.
place (arrow) and secure cable.
6. Disengage cable and then press on the plug
4. Press in caps A.
release (arrow) on the plug D and pull off the
2. Insert ball head of tail light C into clip nut E and
5. Close rear lid.
plug.
fit the light unit into the body (arrow).
Minor Repairs
337
Replacing bulbs at rear
E - Rear fog light
License Plate Lights
F - Turn signal light
1. Remove tail light.
G- Tail light
Changing bulb for license plate light
For information on removing tail lights:
Please see the chapter “REMOVING TAIL
4. Replace the defective bulb (bayonet fitting).
1. Unscrew both screws A and remove the light.
Insert lamp bracket and screw in fastening
LIGHT” on Page 336.
screws.
2. Push the bulb holder apart and pull the bulb
2. Unscrew fastening screws D with the cross-
out.
5. Install tail light.
head screwdriver from the tool kit.
For information on installing tail lights:
3. Replace defective bulb.
3. Remove lamp bracket C.
Please see the chapter “INSTALLING TAIL
4. Insert light, initially tighten both screws A and
LIGHT” on Page 337.
then screw in uniformly.
6. Check operation of lights.
338 Minor Repairs
Lateral adjustment of the headlights should be
carried out at a specialist workshop with an optical
adjustment unit.
Distance
Visual aim shall be performed at not less than
24.6 ft. (7.5 m) (this value is a rounded down con-
version from the 25-foot distance typical of field
aim using a screen). The 24.6 ft. (7.5 m) distance
is measured from the headlamp lens to the
viewing screen.
Floor
The surface upon which the vehicle rests is flat
and approximately level.
Screen
Adjustment
Headlight Adjustment
The screen upon which headlamp beams are pro-
The adjustment is made with the vehicle ready to
jected is perpendicular to the floor and the
f
Check tire pressure and adjust if necessary.
drive and the fuel tank completely filled.
vehicle's longitudinal axis, flat, uniformly light in
f
Please see the chapter “TIRE PRESSURES,
color, unobstructed, and wide and high enough to
The driver's seat must be loaded by a person or a
COLD (68 °F/20 °C)” on Page 354.
accommodate the vehicle beam patterns to be
165lbs. (75kg) weight and the tire pressures must
aimed.
f
Please see the chapter “REPLACING BULBS”
meet the prescribed values. After being loaded,
on Page 326.
the car must be rolled a few meters so that the
The screen should be wide enough to provide at
suspension can settle.
least 3.3 ft. (1 m) of space outboard of the
vehicle's headlamp spacing.
For checking the headlight adjustment, the verti-
cal position of the cutoff of the lowbeam (see fig.)
has to be projected on a vertical screen (wall) in
distance of 24.6 ft. (7.5 m) from the front lens of
the headlamp.The correct position of the cutoff is
3.0 in. (7.5 cm) at 24.6 ft. or 7.5 m (0.4°) below
a horizontal line, x cm from ground to the center
of the headlamp lens.
Minor Repairs
339
Changing headlights from left to
right-hand traffic
If you travel to a country where traffic uses the
other side of the road, the headlights must be
repositioned when you cross the border. The low
beam then lights symmetrically and drivers of
oncoming vehicles are not dazzled.
On the return journey, do not forget to readjust the
headlights.
Height adjustment for low beam/
Repositioning headlights
high beam and additional high beam
1. Please see the chapter “REMOVING HEAD-
1. Switch ignition on.
LIGHTS” on Page 327.
Remove headlight. Press down both release
2. Switch on low beam and/or high beam.
tabs A and remove cover.
3. Open engine compartment lid.
4. Place allen key (6 mm) on adjusting screw.
5. Adjust low beam in direction of the arrow.
340 Minor Repairs
Halogen headlights
Xenon headlight
2. Push lever B down to the stop.
3. Turn spindle C in clockwise direction to the
stop using a crosshead screwdriver.
4. Fit cover on headlight.
Both release tabs A must be fully engaged.
5. Install headlight.
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
6. Reposition the other headlight.
Minor Repairs
341
Bulb Chart
Towing
Certain state statutes and local ordinances prohi-
bit towing with a chain, rope or even a tow bar. In
Exterior lights
Type, rating
addition, damage to your vehicle may result from
improper procedures. Consult your authorized
Halogen low beam and high beam
H7
Porsche dealer for details.
Xenon low beam and high beam
D1S
When the turn signal light is set with the ignition on
Side marker lights, front
W5W
and the emergency warning lights active, only the
Turn signal light, rear
P21W
turn signal light on the corresponding side of the
Turn signal light, front
PY21W
vehicle will light up. After the turn signal light is re-
License plate light
C5W
set, the emergency warning lights will be switched
Fog light
H11
on again.
Rear fog light
P21W
Back up light
P21W
Vehicle towing
Additional high beam
H7
Flat bed towing is the preferred type of towing to
Cornering light
H11
be used on Porsche vehicles. Under certain cir-
cumstances, wheel lifts may be used when the
Interior lights
vehicle will not roll.
The vehicle must be towed with all four
Interior light, front
W5W
wheels off the ground, otherwise damage to
the vehicle may result.
Reading light
W5W
Footwell light
W3W
Glove compartment light
W3W
Center console
W3W
Curb lights (doors)
W3W
Warning lights (doors)
W3W
Curb light (rear lid)
W5W
Guard light (rear lid)
W5W
Luggage compartment light
K12V10W
342 Minor Repairs
Towing hook
Depending on the vehicle equipment, the spare-
wheel well contains one or two towing hooks.
Caution!
Risk of damage to the vehicle.
f Use the towing hook only for an emergency to
remove the vehicle off the road. The towing
hook is to be used only to pull the vehicle onto
the flat bed, tractor or towing aparatus if the
vehicle will roll freely. Under no circumstances
is the vehicle to be secured using the towing
hook.
f Never use the towing hook to tow this or any
other vehicle.
Screwing in rear towing hook
2.Screw in towing hook B as far as the stop (left-
1. Carefully lever out the appropriate plastic
hand thread) and tighten hand-tight.
cover A in the bumper with the screwdriver.
The cover is captive and need not be removed
completely.
Minor Repairs
343
Screwing in front towing hook
2.Screw in towing hook B as far as the stop (left-
Fitting plastic cover at front
1. Carefully lever out the appropriate plastic
hand thread) and tighten hand-tight.
First engage the upper locking tabs of the plastic
cover A in the bumper with the screwdriver.
cover, and then press in the bottom tabs and side
Place cover in the vehicle.
tab uniformly until the tabs have engaged fully.
344 Minor Repairs
4. Carefully feed towing straps through the
opening in the front wheels.
Make sure metal parts of straps do not
damage rim.
Make sure the strap is flat over the rim bead.
Make sure brake backing plate is not
damaged.
5. Secure straps to front of flat bed.
6. Release tension on hoist cable, but do not dis-
connect. Use hoist cable as a safety cable.
Recovering the vehicle
Depending on the vehicle equipment, the spare-
wheel well contains one or two towing lugs.
f When recovering the vehicle, always use two
towing lugs if possible.
Pulling vehicle onto flat bed
Tying down vehicle on flat bed
Screw in the towing lugs only at the front or
rear.
1. Position wooden ramps at the base of the flat
1. Carefully feed towing straps through the
bed to reduce the angle of the pull.
opening in the rear wheels.
Never screw them in so that one towing lug is
Make sure metal parts of straps do not
at the front and one is at the back.
2. Reel in the hoist cable and check the underside
damage rim. Make sure the strap is flat over
of the vehicle for any interference.
the rim bead.
Make sure brake backing plate is not
damaged.
2. Secure straps to rear of flat bed.
3. Reel in hoist cable only far enough to tension
tie-down straps.
Minor Repairs
345
Tire Pressure and Technical Data
Vehicle Identification
347
Engine Data
349
Tires, Rims, Tracks
350
Tire Pressures, Cold (68 °F/20 °C)
354
Weights
356
Ground Clearance
357
Capacities
359
Dimensions
360
Driving Performance
361
346 Tire Pressure and Technical Data
This label contains the following information:
1. Vehicle Identification No.
2. Type/Type description
3. Engine code/Transmission code
4. Paint No./Interior
5. Optional equipment
A duplicate of this label is in your Maintenance
Booklet.
Note
The data bank cannot be reordered when lost or
damaged.
Vehicle Identification
Vehicle identification number
When ordering spare parts or making inquiries,
In accordance with Federal Safety Regulations,
please always quote the vehicle identification
the vehicle identification number of your car is lo-
number.
cated at the bottom left of the windshield frame
and can be seen from the outside and in the lug-
Data bank
gage compartment on the right in front of the tool
box.
The data bank is located on the left under the
loadspace floor.
Tire Pressure and Technical Data
347
For setting “Partially Load”:
1. Correct the setting in the multi-purpose dis-
play.
Please see the chapter “SETTING VEHICLE
LOADING AND ADJUSTING TIRE PRESSURE”
on Page 135.
2. Correct the tire pressure.
Safety compliance sticker
Tire pressure plate
The safety compliance sticker is your assurance
The tire pressure plate is attached to the left-hand-
that your new Porsche complies with all applicable
door aperture.
Federal Motor Vehicle Safety Standards which
The pressures shown on the tire pressure plate re-
were in effect at the time the vehicle was manu-
fer to a fully loaded vehicle. In case the combined
factured.
weight of occupants and cargo does not exceed
The sticker also shows the month and year of pro-
260 kg or 573 lbs the pressures for ”PARTIALLY
duction and the vehicle identification number of
LOADED“ may be used for greater driving com-
your car (perforations) as well as the Gross
fort.
Vehicle Weight Rating and the Gross Axle Weight
f Please see the chapter “TIRE PRESSURES,
Rating.
COLD (68 °F/20 °C)” on Page 354.
f Please see the chapter “LOADING
INFORMATION” on Page 231.
348 Tire Pressure and Technical Data
Engine Data
Cayenne
Cayenne S
Cayenne GTS,
Cayenne S Transsyberia
Type
6-cylinder V-engine
8-cylinder V-engine
8-cylinder V-engine
Number of cylinders
6
8
8
Bore
3.5 in. (89 mm)
3.78 in. (96 mm)
3.78 in. (96 mm)
Stroke
3.8 in. (96.4 mm)
3.27 in. (83 mm)
3.27 in. (83 mm)
Displacement
219.5 cu. in. (3598 cm3)
293.3 cu. in. (4806 cm3)
293.3 cu. in. (4806 cm3)
Net-horsepower
213 kW (290 HP)
283 kW (385 HP)
298 kW (405 HP)
at engine speed
6200 rpm
6200 rpm
6500 rpm
Net. torque
273 ftlb. (370 Nm)
369 ftlb. (500 Nm)
369 ftlb. (500 Nm)
at engine speed
3000 rpm
3500 rpm
3500 rpm
Maximum permitted engine speed
6700 rpm
6700 rpm
6700 rpm
up to 1.5 liters/1000 km
up to 1.5 liters/1000 km
up to 1.5 liters/1000 km (1.6
Engine oil consumption
(1.6 quarts/622 miles)
(1.6 quarts/622 miles)
quarts/622 miles)
Tire Pressure and Technical Data
349