Porshe 911 (997). Manual - part 1057

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1055  1056  1057  1058   ..

 

 

Porshe 911 (997). Manual - part 1057

 

 

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work for wire harness for rear PASM

4385

- Preliminary work
- Removing wire harness for battery wiring
- Installing wire harness for battery wiring
- Subsequent work

Tools

Designation

Type

Number Explanation

repair kit for
harnesses

commercially available
tool

NR.155-1

transmission jack

workshop equipment

WE1082

Preliminary work

Preliminary work for ground strap and B+ line of battery

1. Disconnect battery. → 2706IN Working instructions after disconnecting the

battery

Preliminary work for B+ line from power distributor to transmission
connection point

1. Disconnect battery. → 271000  Work instructions after disconnecting the battery

4386

2. Remove current distributor. → 978919 Removing and installing power distributor - chapter on "Removing"

3. Unscrew triggering unit. → 695319 Removing and installing triggering unit for airbag - chapter on

"Removing"

Note

For vehicles with manual transmission.

4. Remove shift console. → 340819 Removing and installing gearshift bracket - chapter on "Removing"

Note

For vehicles with automatic transmission.

5. Remove selector support. → 370819 Removing and installing selector support - chapter on "Removing"

6. Remove parking-brake lever. → 466119 21 Removing and installing parking-brake lever - section on

"Removing"

7. Remove rear underbody cover. → 519419 Removing and installing rear cover - section on "Removing"

8. Remove cover for centre underbody. → 519319 Removing and installing centre cover - chapter on

"Removing"

Preliminary work for B+ line from starter to transmission connection point

1. Disconnect battery. → 271000  Work instructions after disconnecting the battery

2. Remove throttle housing. → 244219 Removing and installing throttle housing - chapter on "Removing"

3. Remove generator. → 272219 Removing and installing three-phase generator - section on "Removing"

4. Remove rear underbody cover. → 519419 Removing and installing rear cover - section on "Removing"

Preliminary work for engine ground strap

1. Lift the vehicle. → 401000  Raising the

vehicle

Removing wire harness for battery wiring

Removing ground strap and B+ line of battery

Installation Location:

Diagnostic system: reading out fault memory and activating systems

Preliminary work for B+ line from power distributor to transmissionconnection point

4387

Installation position of wire harness for battery wiring

1

- Ground strap for battery

2

- B+ line for battery

Ground strap from battery to body

1. Remove ground strap for battery

-1-

 .

1.1. Unscrew fastening nut of battery ground strap to body and remove ground strap for battery.

Cut through the positive cable.

2. Remove B+ line for battery -2- .

2.1. Cut through the positive cable of main wire harness -3- at the place indicated -arrows- .

2.2.

Diagnostic system: reading out fault memory and activating systems

Removing ground strap and B+ line of battery

4388

 

 

 

 

 

 

 

Content   ..  1055  1056  1057  1058   ..