Opel Frontera UE. Manual - part 842

6E1–251

X22SE 2.2L ENGINE DRIVEABILITY AND EMISSION

Step

No

Yes

Value(s)

Action

15

1. Check items that can cause the engine to run rich.

Refer to Diagnostic Aids in DTC P0172 Diagnostic
Support. 

Make any necessary repairs.

2. Perform the exhaust emission test.

Does the vehicle pass the test?

—

System OK

Go to Step 17

16

1. Check items that can cause the engine to run lean.

Refer to Diagnostic Aids in DTC P0171. 

Make any necessary repairs.

2. Perform the exhaust emission test.

Does the vehicle pass the test?

—

System OK

Go to Step 17

17

Check the EGR system (refer to DTC P0401).

Was a problem found?

—

Verify repair

Go to Step 18

18

Check for the following engine mechanical problems.

D

Low compression

D

Leaking cylinder head gasket

D

Worn or incorrect camshaft

D

Sticking or leaking valves

D

Valve timing

D

Broken Valve springs

Was a problem found?

—

Verify repair

Go to Step 19

19

1. Review all the diagnostic procedures within this

table.

2. If all procedures have been completed and no

malfunctions have been found, review/inspect the
following:

D

Visual/physical inspection

D

Tech 2 data

D

Freeze Frame data/Failure Records buffer

D

All electrical connections within a suspected
circuit and/or system

Was a problem found?

—

Verify repair

Contact

Technical

Assistance

6E1–252

X22SE 2.2L ENGINE DRIVEABILITY AND EMISSION

DIESELING, RUN–ON SYMPTOM

DEFINITION:
Engine continues to run after key is turned OFF, but runs
very rough. If engine runs smoothly, check the ignition
switch and adjustment.

Step

Action

Value(s)

Yes

No

1

Was the On–Board Diagnostic (OBD) System Check
performed?

—

Go to Step 2 

Go to OBD

System

Check 

2

1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,

correct the condition as instructed in the bulletin.

Was a bulletin found that addresses the symptom?

—

Verify repair

Go to Step 3 

3

Was a visual/physical check performed?

—

Go to Step 4 

Go to Visual /

Physical

Check 

4

1. Check for a short between B+ and the ignition feed

circuit.

Was a problem found?

—

Verify repair

Go to Step 5 

5

1. Review all the diagnostic procedures within this

table.

2. If all procedures have been completed and no

malfunctions have been found, review/inspect the
following:

D

Visual/physical inspection

D

Tech 2 data

D

Freeze Frame data/Failure Records buffer

D

All connections within a suspected circuit
and/or system

Was a problem found?

—

Verify repair

Contact

Technical

Assistance

6E1–253

X22SE 2.2L ENGINE DRIVEABILITY AND EMISSION

BACKFIRE SYMPTOM

DEFINITION:
Fuel ignites in the intake manifold, or in the exhaust
system, making a loud popping noise.

Step

Action

Value(s)

Yes

No

1

Was the On–Board Diagnostic (OBD) System Check
performed?

—

Go to Step 2 

Go to OBD

System

Check 

2

1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,

correct the condition as instructed in the bulletin.

Was a bulletin found that addresses the symptom?

—

Verify repair

Go to Step 3 

3

Was a visual/physical check performed?

—

Go to Step 4 

Go to Visual /

Physical

Check 

4

Check for proper ignition voltage output with spark
tester 5-8840-0383-0.

Was a problem found?

—

Verify repair

Go to Step 5 

5

1. Remove the spark plugs and check for gas or oil

fouling, cracks, wear, improper gap, burned
electrodes of heavy deposits.

2. If spark plugs are fouled, the cause of fouling must

be determined before replacing the spark plugs.

Was a problem found?

—

Verify repair

Go to Step 6 

6

1. Visually/physically inspect the secondary ignition

wires. Check for the following conditions:

D

Verify that all ignition wire resistances are less
than the specified value.

D

Verify that ignition wires are correctly routed to
eliminate cross–firing.

D

Verify that ignition wires are not arcing to
ground. Spraying the secondary ignition wires
with a light mist of water may help locate an
intermittent problem.

Was a problem found?

—

Verify repair

Go to Step 7 

7

Check for an intermittent ignition system malfunction:

D

Intermittent CKP 58X signal.

D

Intermittent ignition feed circuit or sensor ground
circuit to the crankshaft position sensor.

Was a problem found?

—

Verify repair

Go to Step 8 

8

To determine if there is a problem with fuel delivery, 
refer to Fuel System Diagnosis.

Was a problem found?

—

Verify repair

Go to Step 9 

9

1. Check for the following engine mechanical

problems:

D

Low compression

D

Leaking cylinder head gasket

D

Worn or incorrect camshaft

D

Incorrect valve timing

D

Sticking or leaking valves

D

Camshaft drive belt slipped or stripped.

Was a problem found?

—

Verify repair

Go to Step 10

6E1–254

X22SE 2.2L ENGINE DRIVEABILITY AND EMISSION

Step

No

Yes

Value(s)

Action

10

Check the intake and exhaust manifold(s) for casting
flash. Refer to Engine Mechanical.

Was a problem found?

—

Verify repair

Go to Step 11

11

1. Review all the diagnostic procedures within this

table.

2. If all procedures have been completed and no

malfunctions have been found, review/inspect the
following:

D

Visual/physical inspection

D

Tech 2 data

D

Freeze Frame data/Failure Records buffer

D

All electrical connections within a suspected
circuit and/or system

Was a problem found?

—

Verify repair

Contact

Technical

Assistance