Nissan Cube. Manual - part 900

B1132 SIDE AIR BAG MODULE RH

SRC-117

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-12, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-116, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-118

< DTC/CIRCUIT DIAGNOSIS >

B1134 SIDE AIR BAG MODULE LH

B1134 SIDE AIR BAG MODULE LH

Description

INFOID:0000000009946235

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946236

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-118, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946237

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-118, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

DTC

Display contents of CON-

SULT

DTC detecting condition

Possible cause

B1134

SIDE MODULE LH 
[OPEN]

Side air bag module LH circuit is open

• Disconnection of wiring harness and open
• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit

B1134 SIDE AIR BAG MODULE LH

SRC-119

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module LH. Refer to 

SE-12, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-118, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-120

< DTC/CIRCUIT DIAGNOSIS >

B1135 SIDE AIR BAG MODULE LH

B1135 SIDE AIR BAG MODULE LH

Description

INFOID:0000000009946238

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946239

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-120, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946240

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-120, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1135

SIDE MODULE LH 
[VB-SHORT]

Side air bag module LH circuit is shorted to 
power supply circuit

• Disconnection of wiring harness and short
• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit