Nissan Cube. Manual - part 1030

 

  Index      Nissan     Nissan Cube (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1028  1029  1030  1031   ..

 

 

Nissan Cube. Manual - part 1030

 

 

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

WT-11

< SYSTEM DESCRIPTION >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

WORK SUPPORT MODE

Refer to 

WT-24, "Work Procedure"

.

SELF-DIAG RESULTS MODE

Refer to 

BCS-82, "DTC Index"

.

DATA MONITOR MODE

Screen of data monitor mode is displayed.
NOTE:
• When malfunction is detected, CONSULT perform REAL-TIME DIAGNOSIS.

Also, any malfunction detected while in this mode will be displayed at real time.

• The following table includes information(items)inapplicable to this vehicle. For information(items)applicable

to this vehicle, refer to CONSULT display items.

NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT.

ACTIVE TEST MODE

NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT.

TEST ITEM LIST

Diagnostic test mode

Function

Work support

In this mode, it is possible to make quick and accurate adjustments by following the instruc-
tions on the CONSULT display.

Self diagnostic result

Receives self-diagnosis results from the BCM, and indicates DTCs and the number of mal-
functions.

Data monitor

Receives input/output signals from the BCM and indicates and stores them to facilitate locating 
the causes of malfunctions.

Active test

Transmits command to the BCM to change output signals and check operation of output sys-
tem.

Monitor item (Unit)

Remark

AIR PRESS FL (kPa), (kg/cm

2

), (Psi)

Air pressure of tires

AIR PRESS FR (kPa), (kg/cm

2

), (Psi)

AIR PRESS RR (kPa), (kg/cm

2

), (Psi)

AIR PRESS RL (kPa), (kg/cm

2

), (Psi)

ID REGST FL1 

ID is registered: Done
ID is not registered: Yet 

ID REGST FR1

ID REGST RR1 

ID REGST RL1 

WARNING LAMP

Low tire pressure warning lamp ON: On
Low tire pressure warning lamp OFF: Off

BUZZER

Combination meter buzzer ON: On
Combination meter buzzer OFF: Off

Test item

Content

WARNING LAMP

This test is able to check to check that the low tire pressure warning lamp turns on.

ID REGIST WARNING

This test is able to check to check that the buzzer sounds or the low tire pressure warning lamp 
turns on.

RUN FLAT TIRE W/L

NOTE:
This item is displayed, but cannot be use this item.

WT-12

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

FLASHER

This test is able to check to check that each turn signal lamp turns on.

HORN

This test is able to check to check that the horn sounds.

Test item

Content

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

WT-13

< SYSTEM DESCRIPTION >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000009949847

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function

INFOID:0000000009949848

FUNCTION

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp control

INT LAMP

×

×

×

Remote keyless entry system

MULTI REMOTE ENT

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

Manual air conditioner

AIR CONDITONER

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door

TRUNK

×

Vehicle security system

THEFT ALM

×

×

×

RAP system

RETAINED PWR

×

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

TPMS (AIR PRESSURE MONITOR)

×

×

×

Panic alarm system

PANIC ALARM

×

WT-14

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

The diagnosis functions (main functions) include the following: “WORK SUPPORT”, “SELF DIAGNOSTIC
RESULT”, “DATA MONITOR” and “ACTIVE TEST”.

WORK SUPPORT MODE

Refer to 

WT-24, "Work Procedure"

.

SELF-DIAG RESULTS MODE

Refer to 

BCS-150, "DTC Index"

.

DATA MONITOR MODE

Screen of data monitor mode is displayed.
NOTE:
• When malfunction is detected, CONSULT perform REAL-TIME DIAGNOSIS.

Also, any malfunction detected while in this mode will be displayed at real time.

• The following table includes information(items)inapplicable to this vehicle. For information(items)applicable

to this vehicle, refer to CONSULT display items.

NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT.

ACTIVE TEST MODE

NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT.

TEST ITEM LIST

Diagnostic test mode

Function

Work support

In this mode, it is possible to make quick and accurate adjustments by following the instruc-
tions on the CONSULT display.

Self diagnostic result

Receives self-diagnosis results from the BCM, and indicates DTCs and the number of mal-
functions.

Data monitor

Receives input/output signals from the BCM and indicates and stores them to facilitate locating 
the causes of malfunctions.

Active test

Transmits command to the BCM to change output signals and check operation of output sys-
tem.

Monitor item (Unit)

Remark

AIR PRESS FL (kPa), (kg/cm

2

), (Psi)

Air pressure of tires

AIR PRESS FR (kPa), (kg/cm

2

), (Psi)

AIR PRESS RR (kPa), (kg/cm

2

), (Psi)

AIR PRESS RL (kPa), (kg/cm

2

), (Psi)

ID REGST FL1 

ID is registered: Done
ID is not registered: Yet 

ID REGST FR1

ID REGST RR1 

ID REGST RL1 

WARNING LAMP

Low tire pressure warning lamp ON: On
Low tire pressure warning lamp OFF: Off

BUZZER

Combination meter buzzer ON: On
Combination meter buzzer OFF: Off

Test item

Content

WARNING LAMP

This test is able to check to check that the low tire pressure warning lamp turns on.

ID REGIST WARNING

This test is able to check to check that the buzzer sounds or the low tire pressure warning lamp 
turns on.

 

 

 

 

 

 

 

Content   ..  1028  1029  1030  1031   ..