Nissan Cube. Manual - part 99

BRC-46

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1116 STOP LAMP SWITCH

C1116 STOP LAMP SWITCH

Description

INFOID:0000000009949942

The stop lamp switch transmits the stop lamp switch signal (ON/OFF) to the ABS actuator and electric unit
(control unit). 

DTC Logic

INFOID:0000000009949943

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

DTC REPRODUCTION PROCEDURE

1.

Turn the ignition switch ON.

2.

Perform self-diagnosis for “ABS” with CONSULT.

Is DTC “C1116” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-46, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009949944

NOTE:
DTC “C1116” may be detected when the brake pedal and the accelerator pedal are simultaneously depressed
for 1 minute or more while driving the vehicle. This is not a malfunction.

1.

INTERVIEW FROM THE CUSTOMER

Check if the brake pedal and the accelerator pedal are simultaneously depressed for 1 minute or more while
driving the vehicle.
Is there such a history?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

PERFORM SELF-DIAGNOSIS

1.

Erase self-diagnosis result for “ABS” with CONSULT.

2.

Turn the ignition switch OFF, and wait 10 seconds or more.

3.

Start the engine.

CAUTION:

Never start the vehicle.

4.

Depress the brake pedal several times.

5.

Perform self-diagnosis for “ABS” with CONSULT.

Is DTC “C1116” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

STOP LAMP FOR ILLUMINATION

Depress brake pedal and check that stop lamp turns ON.

DTC

Display item

Malfunction detected condition

Possible cause

C1116

STOP LAMP SW

When a stop lamp switch signal is not input where the 
brake pedal is depressed.

• Harness or connector
• Stop lamp switch
• ABS actuator and electric unit 

(control unit)

C1116 STOP LAMP SWITCH

BRC-47

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Does stop lamp turn ON?

YES

>> GO TO 5.

NO

>> Check stop lamp system. Refer to 

EXL-58, "Diagnosis Procedure"

. GO TO 4.

4.

CHECK DATA MONITOR (1)

1.

Erase self-diagnosis result for “ABS” with CONSULT.

2.

Turn the ignition switch OFF, and wait 10 seconds or more.

3.

Start the engine.

CAUTION:

Never start the vehicle.

4.

Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order with CONSULT. Check
that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to 

BRC-88, "Refer-

ence Value"

.

5.

Select “ABS”, “DATA MONITOR” and “pressure sensor” according to this order. Check that data monitor
displays “5 bar” or less when brake pedal is depress. Refer to 

BRC-88, "Reference Value"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 5.

5.

CHECK STOP LAMP SWITCH CLEARANCE

1.

Turn the ignition switch OFF.

2.

Check stop lamp switch clearance. Refer to 

BR-7, "Inspection and Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Adjust stop lamp switch clearance. Refer to 

BR-7, "Inspection and Adjustment"

. GO TO 6.

6.

CHECK DATA MONITOR (2)

1.

Erase self-diagnosis result for “ABS” with CONSULT.

2.

Turn the ignition switch OFF, and wait 10 seconds or more.

3.

Start the engine.

CAUTION:

Never start the vehicle.

4.

Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order with CONSULT. Check
that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to 

BRC-88, "Refer-

ence Value"

.

5.

Select “ABS”, “DATA MONITOR” and “pressure sensor” according to this order. Check that data monitor
displays “5 bar” or less when brake pedal is depress. Refer to 

BRC-88, "Reference Value"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 7.

7.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to 

BRC-49, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace stop lamp switch. Refer to 

BR-17, "Exploded View"

. GO TO 8.

8.

CHECK DATA MONITOR (3)

1.

Erase self-diagnosis result for “ABS” with CONSULT.

2.

Turn the ignition switch OFF, and wait 10 seconds or more.

3.

Start the engine.

CAUTION:

Never start the vehicle.

4.

Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order with CONSULT. Check
that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to 

BRC-88, "Refer-

ence Value"

.

5.

Select “ABS”, “DATA MONITOR” and “pressure sensor” according to this order. Check that data monitor
displays “5 bar” or less when brake pedal is depress. Refer to 

BRC-88, "Reference Value"

.

Is the inspection result normal?

BRC-48

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1116 STOP LAMP SWITCH

YES

>> INSPECTION END

NO

>> GO TO 9.

9.

CHECK CONNECTOR AND TERMINAL

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) harness connector.

3.

Check ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

4.

Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.

5.

Disconnect stop lamp switch harness connector.

6.

Check stop lamp switch harness connector for disconnection or looseness.

7.

Check stop lamp switch pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Repair or replace error-detected parts. GO TO 10.

10.

CHECK DATA MONITOR (4)

1.

Connect ABS actuator and electric unit (control unit) harness connector.

2.

Connect stop lamp switch harness connector.

3.

Erase self-diagnosis result for “ABS” with CONSULT.

4.

Turn the ignition switch OFF, and wait 10 seconds or more.

5.

Start the engine.

CAUTION:

Never start the vehicle.

6.

Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order with CONSULT. Check
that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to 

BRC-88, "Refer-

ence Value"

.

7.

Select “ABS”, “DATA MONITOR” and “pressure sensor” according to this order. Check that data monitor
displays “5 bar” or less when brake pedal is depress. Refer to 

BRC-88, "Reference Value"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 11.

11.

CHECK STOP LAMP SWITCH CIRCUIT (1)

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) harness connector.

3.

Check voltage between ABS actuator and electric unit (control unit) harness connector and ground.

4.

Turn the ignition switch ON.

5.

Check voltage between ABS actuator and electric unit (control unit) harness connector and ground.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-113, "Exploded View"

.

NO

>> Repair or replace error-detected parts. GO TO 12.

12.

CHECK STOP LAMP SWITCH CIRCUIT (2)

1.

Turn the ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

ABS actuator and electric unit (control unit)

—

Condition

Voltage

Connector

Terminal

E36

20

Ground

Brake pedal depressed

Battery voltage

Brake pedal not depressed

Approx. 0 V

ABS actuator and electric unit (control unit)

—

Condition

Voltage

Connector

Terminal

E36

20

Ground

Brake pedal depressed

Battery voltage

Brake pedal not depressed

Approx. 0 V

C1116 STOP LAMP SWITCH

BRC-49

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

3.

Check continuity between ABS actuator and electric unit (control unit) harness connector and stop lamp
switch harness connector.

*1: With M/T
*2: With CVT

4.

Check continuity between ABS actuator and electric unit (control unit) harness connector and the ground.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-113, "Exploded View"

.

NO

>> Repair or replace error-detected parts. GO TO 13.

13.

CHECK DATA MONITOR (5)

1.

Connect ABS actuator and electric unit (control unit) harness connector.

2.

Connect stop lamp switch harness connector.

3.

Erase self-diagnosis result for “ABS” with CONSULT.

4.

Turn the ignition switch OFF, and wait 10 seconds or more.

5.

Start the engine.

CAUTION:

Never start the vehicle.

6.

Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order with CONSULT. Check
that data monitor displays “On” or “Off” when brake pedal is depress or release. Refer to 

BRC-88, "Refer-

ence Value"

.

7.

Select “ABS”, “DATA MONITOR” and “pressure sensor” according to this order. Check that data monitor
displays “5 bar” or less when brake pedal is depress. Refer to 

BRC-88, "Reference Value"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-113, "Exploded View"

.

Component Inspection

INFOID:0000000009949945

1.

CHECK STOP LAMP SWITCH

1.

Turn the ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check continuity between stop lamp switch harness connector terminals. 

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-17, "Exploded View"

.

ABS actuator and electric unit (control unit)

Stop lamp switch

Continuity

Connector

Terminal

Connector

Terminal

E36

20

E114

*1

2

Existed

E115

*2

ABS actuator and electric unit (control unit)

—

Continuity

Connector

Terminal

E36

20

Ground

Not existed

Stop lamp switch

Condition

Continuity

Terminal

1 – 2

Release stop lamp switch
(When brake pedal is depressed.)

Existed

Push stop lamp switch
(When brake pedal is released.)

Not existed