Nissan Versa Sedan. Manual - part 864

TM-362

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0715 INPUT SPEED SENSOR A

6.

CHECK CIRCUIT BETWEEN IPDM E/R AND PRIMARY SPEED SENSOR (PART 1)

1. Disconnect  IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector terminal and primary speed sensor harness con-

nector terminal. 

Is the check result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND PRIMARY SPEED SENSOR (PART 2)

Check continuity between IPDM E/R harness connector terminal and ground. 

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Harness open circuit or short circuit between  ignition switch and IPDM E/R. Refer to 

PG-20, "Wiring Dia-

gram — Ignition Power Supply —"

.

• 10A fuse (No.49, IPDM E/R). Refer to 

PG-62, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

IPDM E/R

Primary speed sensor

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F50

3

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E45

21

Ground

Not existed

P0720 OUTPUT SPEED SENSOR

TM-363

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0720 OUTPUT SPEED SENSOR

DTC Logic

INFOID:0000000009268165

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P0720” detected?

YES

>> Go to 

TM-363, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268166

1.

CHECK OUTPUT SPEED SENSOR POWER CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect output speed sensor connector.

3. Turn ignition switch ON.

4. Check  voltage between  output speed sensor harness connector terminal and ground.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0720

Output Speed Sensor Circuit

The output speed sensor value is less than 
150 rpm continuously for 10 seconds or more 
under the following diagnosis conditions:
• Diagnosis conditions
- Selector lever: “D”, “L” or “R” position 
- Auxiliary gearbox shifting is not in progress. 
- When the “D” position switch, “L” position 

switch or “R” position switch is ON, the out-
put speed has not experienced 250 rpm or 
more. 

- After shifting the selector lever, the input 

speed has experienced less than 300 rpm.

- Secondary pulley speed: 1,500 rpm or more
- TCM power supply voltage: More than 11 V

• Harness or connector

(Output speed sensor circuit is open or 
shorted)

• Output speed sensor

The output speed sensor value is 90 rpm or 
less continuously for 500 msec or more under 
the following diagnosis conditions:
• Diagnosis conditions
- 10-msec-ago output speed: 730 rpm or 

more

- TCM power supply voltage: More than 11 V

Selector lever

: “D” position

Vehicle speed

: 55 km/h (34 MPH) or more

TM-364

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0720 OUTPUT SPEED SENSOR

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> GO TO 6.

2.

CHECK OUTPUT SPEED SENSOR GROUND CIRCUIT

Check  continuity between  output speed sensor harness connector terminal and ground.

Is the inspection result normal?

YES 

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 1)

1. Turn ignition switch OFF.

2. Disconnect  TCM connector.

3. Check  continuity between  output speed sensor harness connector terminal and  TCM harness connector

terminal.

Is the inspection result normal?

YES 

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 2)

Check  continuity between  output speed sensor harness connector terminal and ground.

Is the inspection result normal?

YES 

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK TCM INPUT SIGNALS

1. Connect all of  disconnected connectors.

2. Lift the vehicle.

3. Start the engine.

4. Check  frequency of  output speed sensor.

Output speed sensor

Ground

Voltage

Connector

Terminal

F41

3

Ground

10 – 16 V

Output speed sensor

Ground

Continuity

Connector

Terminal

F41

1

Ground

Existed

Output speed sensor

TCM

Continuity

Connector

Terminal

Connector

Terminal

F41

2

F44

24

Existed

Output speed sensor

Ground

Continuity

Connector

Terminal

F41

2

Ground

Not existed

P0720 OUTPUT SPEED SENSOR

TM-365

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace  output speed sensor. Refer to 

TM-444, "Removal and Installation"

.

6.

CHECK CIRCUIT BETWEEN IPDM E/R AND OUTPUT SPEED SENSOR (PART 1)

1. Disconnect  IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector terminal and output speed sensor harness con-

nector terminal. 

Is the check result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND OUTPUT SPEED SENSOR (PART 2)

Check continuity between IPDM E/R harness connector terminal and ground. 

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Harness open circuit or short circuit between  ignition switch and IPDM E/R. Refer to 

PG-20, "Wiring Dia-

gram — Ignition Power Supply —"

.

• 10A fuse (No.49, IPDM E/R). Refer to 

PG-62, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

TCM

Ground

Condition

Data

Connector

Terminal

F44

24

Ground

• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)

Approx. 200 Hz

JSDIA1904GB

IPDM E/R

Output speed sensor

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F41

3

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E45

21

Ground

Not existed