Nissan Rogue. Manual - part 615

OPTICAL SENSOR

EXL-89

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

8.

CHECK OPTICAL SENSOR SHORT CIRCUIT

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> Repair or replace harness.

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M13

2

M18

19

Yes

Optical sensor

Ground

Continuity

Connector

Terminal

M13

2

No

EXL-90

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

HAZARD SWITCH

HAZARD SWITCH

Component Function Check

INFOID:0000000011280741

1.

CHECK HAZARD SWITCH SIGNAL BY CONSULT

CONSULT DATA MONITOR

1. Turn ignition switch ON.

2. Select “HAZARD SW” in “Data Monitor” of “BCM (FLASHER)”.

3. With operating the hazard switch, check the monitor status.

Is the inspection result normal?

YES

>> Hazard switch circuit is normal.

NO

>> Refer to 

EXL-90, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011280742

1.

CHECK HAZARD SWITCH SIGNAL INPUT

1. Turn ignition switch OFF.

2. Disconnect hazard switch connector.

3. Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between hazard switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

 (with Intelligent Key system) or 

BCS-

135, "Removal and Installation"

 (without Intelligent Key system).

NO

>> Repair or replace harness.

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

ON

On

OFF

Off

(+)

(

−)

Voltage (Approx.)

Hazard switch

Connector

Terminal

M26

2

Ground

Battery voltage

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M26

2

M18

11

Yes

Hazard switch

Ground

Continuity

Connector

Terminal

M26

2

No

HAZARD SWITCH

EXL-91

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

4.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch. Refer to 

EXL-125, "Removal and Installation"

.

NO

>> Repair or replace harness.

Hazard switch

Ground

Continuity

Connector

Terminal

M26

3

Yes

EXL-92

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

TURN SIGNAL LAMP CIRCUIT

TURN SIGNAL LAMP CIRCUIT

Description

INFOID:0000000011421526

The BCM monitors inputs from the combination switch (lighting and turn signal switch) to determine when to

activate the turn signals. The BCM outputs voltage direction to the left and right turn signals during turn signal

operation or both during hazard warning operation. The BCM sends a turn signal indicator request to the com-

bination meter via the CAN communication lines. 

The BCM performs the fast flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is

open.

NOTE:

Turn signal lamp blinks at normal speed when using the hazard warning lamp.

Component Function Check

INFOID:0000000011421527

1.

CHECK TURN SIGNAL LAMP

CONSULT 

1. Select “FLASHER” in “Active Test” of “BCM (FLASHER)”.

2. While operating the test items, check that the turn signal lamp blinks.

Is the inspection result normal?

YES

>> Turn signal lamp circuit is normal.

NO

>> Refer to 

EXL-92, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011421528

Regarding Wiring Diagram information, refer to 

EXL-55, "Wiring Diagram"

.

1.

CHECK TURN SIGNAL LAMP BULB

Check the applicable lamp bulb to be sure the proper bulb standard is in use and the bulb is not open.
Is the bulb OK?

YES

>> GO TO 2.

NO

>> Replace the bulb.

2.

CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

1. Turn the ignition switch OFF.

2. Disconnect the front combination lamp harness connector, door mirror harness connector or the side turn

signal harness connector or the rear combination lamp harness connector in question.

3. Turn the ignition switch ON.

4. Operate the turn signal switch.

5. While the turn signal is operating, check the voltage between the front combination lamp harness connec-

tor and ground.

LH

: Turn signal lamps (LH) ON

RH

: Turn signal lamps (RH) ON

Off

: Turn signal lamps OFF

(+)

(

−)

Voltage

(Approx.)

Connector

Terminal