Nissan Rogue. Manual - part 432

DMS-30

< DTC/CIRCUIT DIAGNOSIS >

[ECO MODE]

ECO MODE SWITCH

DTC/CIRCUIT DIAGNOSIS

ECO MODE SWITCH

Component Function Check

INFOID:0000000011317492

1.

 CHECK ECO MODE SWITCH OPERATION

1. Turn ignition switch ON.

2. Check ECO mode indicator lamp turns ON/OFF on combination meter when turn ECO mode switch ON/

OFF.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

DMS-33, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011317493

1.

DETECT MALFUNCTIONING ITEMS

What is malfunction item?

ECO mode switch illumination does not turn ON>>GO TO 2.

ECO mode indicator does not turn ON>>GO TO 7.

2.

CHECK ECO MODE SWITCH ILLUMINATION POWER SUPPLY (PART 1)

1. Turn OFF the headlamp.

2. Turn ignition switch OFF.

3. Disconnect ECO mode switch harness connector.

4. Turn ignition switch ON.

5. Turn ON the headlamp.

6. Check the voltage between ECO mode switch harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

CHECK INTERMITTENT INCIDENTE

Refer to 

GI-44, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace ECO mode switch. Refer to 

DMS-34, "Removal and Installation"

.

NO

>> Replace the fuse after repair the applicable circuit.

4.

CHECK ECO MODE SWITCH ILLUMINATION POWER SUPPLY (PART 2)

Check the voltage between ECO mode switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

ECO mode switch

Voltage

(Approx.)

Connector

+

–

Terminal

M1

1

4

12 V

+

−

Voltage

(Approx.)

ECO mode switch

Connector

Terminal

M1

1

Ground

12 V

DMS

ECO MODE SWITCH

DMS-31

< DTC/CIRCUIT DIAGNOSIS >

[ECO MODE]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

5.

CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH

1. Disconnect combination meter connector M77.

2. Check the continuity between combination meter harness connector terminal and ECO mode switch har-

ness connector terminal.

3. Also check harness for short to ground.
Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK GROUND CIRCUIT

1. Turn OFF the headlamp.

2. Turn ignition switch OFF.

3. Check continuity between ECO mode switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK ECO MODE SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECO mode switch connector.

3. Turn ignition switch ON.

4. Check voltage between ECO mode switch harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> GO TO 8.

8.

CHECK GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check the continuity between ECO mode switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace malfunctioning parts.

9.

CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH (PART 1)

1. Disconnect combination meter harness connector M76.

Combination meter

ECO mode switch

Continuity

Connector

Terminal

Connector

Terminal

M77

43

M1

1

Existed

ECO mode switch

—

Continuity

Connector

Terminal

M1

4

Ground

Existed

ECO mode switch

Voltage

(Approx.)

Connector

+

−

Terminal

M1

6

8

10 V

ECO mode switch

—

Continuity

Connector

Terminal

M1

8

Ground

Existed

DMS-32

< DTC/CIRCUIT DIAGNOSIS >

[ECO MODE]

ECO MODE SWITCH

2. Check continuity between combination meter harness connector terminal and ECO mode switch harness

connector terminal.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

10.

CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH (PART 2)

Check continuity between combination meter harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Repair or replace malfunctioning parts.

11.

CHECK COMBINATION METER INPUT/OUTPUT SIGNAL

1. Connect all of disconnected connectors.

2. Check input/output signal of combination meter. Refer to 

MWI-25, "Reference Value"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

12.

CHECK ECO MODE SWITCH

Check ECO mode switch. Refer to 

DMS-32, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Replace ECO mode switch. Refer to 

DMS-34, "Removal and Installation"

.

Component Inspection

INFOID:0000000011317494

1.

CHECK ECO MODE SWITCH

Check continuity between ECO mode switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ECO mode switch. Refer to 

DMS-34, "Removal and Installation"

.

Combination meter

ECO mode switch

Continuity

Connector

Terminal

Connector

Terminal

M76

9

M1

6

Existed

Combination meter

—

Continuity

Connector

Terminal

M76

9

Ground

Not existed

ECO mode switch

Condition

Continuity

Terminal

6 – 8

ECO mode switch is depressed.

Existed

ECO mode switch is released.

Not existed

DMS

THE ECO MODE INDICATOR LAMP DOES NOT TURN ON

DMS-33

< SYMPTOM DIAGNOSIS >

[ECO MODE]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

SYMPTOM DIAGNOSIS

THE ECO MODE INDICATOR LAMP DOES NOT TURN ON

Description

INFOID:0000000011317495

The ECO mode indicator lamp does not turn ON when the ECO mode switch is operated.

Diagnosis Procedure

INFOID:0000000011317496

1.

PERFORM COMBINATION METER ON BOARD DIAGNOSIS

Perform combination meter on board diagnosis. Refer to 

MWI-19, "Description"

.

Is the check result normal?

YES

>> GO TO 2.

NO

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

2.

CHECK DTC (TCM)

With CONSULT

1. Start the engine.

2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

TM-63, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK DTC (ECM)

With CONSULT

Check “Self Diagnostic Results” in “ENGINE”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

EC-96, "DTC Index"

.

NO

>> GO TO 4.

4.

CHECK DTC (COMBINATION METER)

With CONSULT

Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

MWI-31, "DTC Index"

.

NO

>> GO TO 5.

5.

CHECK COMBINATION METER INPUT/OUTPUT SIGNAL

With CONSULT

1. Select “Data Monitor” in “METER/M&A”.

2. Select “ECO MODE IND”.

3. Check that “ECO MODE IND” turns ON/OFF when ECO mode switch is operated. Refer to 

MWI-25, "Ref-

erence Value"

.

Is any DTC detected?

YES

>> Replace combination meter. Refer to 

MWI-86, "Disassembly and Assembly"

.

NO

>> GO TO 6.

6.

CHECK ECO MODE SWITCH CIRCUIT

Check ECO mode switch circuit. Refer to 

DMS-30, "Diagnosis Procedure"

.

Is any DTC detected?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning parts.