Nissan Rogue. Manual - part 1078

B2604 SHIFT POSITION

SEC-91

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

3. Check voltage between transmission range switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between transmission range switch harness connector and IPDM E/R harness connec-

tor.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-40, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK BCM INPUT SIGNAL

1. Turn ignition switch OFF.

2. Reconnect transmission range switch connector.

3. Turn ignition switch ON.

4. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> GO TO 6.

6.

CHECK BCM INPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect transmission range switch connector.

3. Disconnect BCM connector.

4. Check continuity between transmission range switch harness connector and BCM harness connector.

5. Check continuity between transmission range switch harness connector and ground.

Is the inspection result normal?

(+)

(–)

Voltage (V)

(Approx.)

Transmission range switch

Connector

Terminal

F78

7

Ground

Battery voltage

Transmission range switch

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

F78

7

F35

70

Yes

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M19

89

Ground

Selector lever

P or N position

Battery voltage

Other than above

0

Transmission range switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

F78

10

M19

89

Yes

Transmission range switch

Ground

Continuity

Connector

Terminal

F78

10

No

2015 Rogue NAM

SEC-92

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2604 SHIFT POSITION

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK TRANSMISSION RANGE SWITCH

Refer to 

SEC-92, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace transmission range switch. 

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

9.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

>> Inspection End.

Component Inspection

INFOID:0000000011278498

1.

CHECK TRANSMISSION RANGE SWITCH

1. Turn ignition switch OFF.

2. Disconnect transmission range switch connector.

3. Check continuity between transmission range switch terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace transmission range switch. 

Transmission range switch

Condition

Continuity

Terminal

7

10

P or N position

Yes

Other than above

No

2015 Rogue NAM

B2608 STARTER RELAY

SEC-93

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2608 STARTER RELAY

DTC Logic

INFOID:0000000011278499

DTC DETECTION LOGIC

NOTE:

• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

• If DTC B2608 is displayed with other DTC (BCM), first perform the trouble diagnosis for other DTC detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine:

-

Selector lever: In the P position

-

Brake pedal: Depressed

2. Wait 1 second after engine started.

3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-93, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278500

1.

CHECK DTC OF IPDM E/R

Select “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

PCS-22, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2608

STARTER RELAY

BCM outputs starter relay OFF signal but 
BCM receives starter relay ON signal from 
IPDM E/R (CAN).

• Harness or connectors

(The CAN communication line is open or 
shorted.)

• Harness or connectors 

(Starter relay circuit is open or shorted.)

• IPDM E/R
• Starter relay

2015 Rogue NAM

SEC-94

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B260F ENGINE STATUS

B260F ENGINE STATUS

Description

INFOID:0000000011278501

BCM receives the engine status signal from ECM via CAN communication.

DTC Description

INFOID:0000000011278502

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connectors

(The CAN communication line is open or shorted.)

• ECM

FAIL-SAFE

Inhibit engine cranking

DTC CONFIRMATION PROCEDURE

1.

CHECK DTC PRIORITY

If DTC B260F is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or

U1010.
Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. U1000: Refer to 

BCS-64, "DTC Logic"

. U1010: Refer to 

BCS-65,

"DTC Logic"

.

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON and wait 2 seconds or more.

2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Refer to 

SEC-94, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: Inspection End.

Diagnosis Procedure

INFOID:0000000011278503

1.

CHECK DTC PRIORITY

If DTC B260F is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or

U1010.
Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. U1000: Refer to 

BCS-64, "DTC Logic"

. U1010: Refer to 

BCS-65,

"DTC Logic"

.

NO

>> GO TO 2.

2.

INSPECTION START

1. Turn ignition switch ON.

2. Select “Self Diagnostic Result” of “BCM” using CONSULT.

3. Touch “ERASE”.

4. Perform DTC CONFIRMATION PROCEDURE for DTC B260F. Refer to 

SEC-94, "DTC Description"

.

Is DTC detected?

YES

>> GO TO 3.

NO

>> Inspection End.

DTC No.

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B260F

ENG STATE SIG LOST
(Engine state signal lost)

BCM has not yet received the engine status signal from ECM when ignition 
switch is in the ON position.

2015 Rogue NAM