Nissan Rogue. Manual - part 94

 

  Index      Nissan     Nissan Rogue (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  92  93  94  95   ..

 

 

Nissan Rogue. Manual - part 94

 

 

AV-368

< SYMPTOM DIAGNOSIS >

[NAVIGATION WITH BOSE]

NORMAL OPERATING CONDITION

- Because calculation of the current location cannot be done when traveling with the ignition off, for example

when traveling by ferry or when being towed, the location before travel is displayed. If the precise location

can be detected with GPS, the location will be corrected.

Vehicle Mark Jumps

In the following cases, the vehicle mark may appear to jump as a result of automatic correction of the current

location:

• When map matching has been done

- If the current location and the vehicle mark are different when map matching is done, the vehicle mark may

seem to jump. At this time, the location may be “corrected” to the wrong road or to a location which is not on

a road.

• When GPS location correction has been done

- If the current location and the vehicle mark are different when the location is corrected using GPS measure-

ments, the vehicle mark may seem to jump. At this time, the location may be “corrected” to a location which

is not on a road.

Vehicle Mark is in a River or Sea

The navigation system moves the vehicle mark with no distinction between land and rivers or sea. If the vehi-

cle mark is somehow out of place, it may appear that the vehicle is driving in a river or the sea.

Vehicle Mark Automatically Rotates

The system wrongly memorizes the rotating status as stopping when the ignition switch is turned ON with the

turntable rotating. That causes the vehicle mark to rotate when the vehicle is stopped.

When Driving on Same Road, Sometimes Vehicle Mark is in Right Place and Sometimes it is in Wrong Place

The conditions of the GPS antenna (GPS data) and gyroscope (angular speed sensor) change gradually.

Depending on the road traveled and the operation of the steering wheel, the location detection results will be

different. Therefore, even on a road on which the location has never been wrong, conditions may cause the

vehicle mark to deviate.

AV

AV CONTROL UNIT

AV-369

< REMOVAL AND INSTALLATION >

[NAVIGATION WITH BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

REMOVAL AND INSTALLATION

AV CONTROL UNIT

Exploded View

INFOID:0000000011277018

Removal and Installation

INFOID:0000000011277019

REMOVAL

CAUTION:

• Before disconnecting the AV control unit and battery terminals, turn the ignition switch OFF and wait

at least 30 seconds.

• Before replacing AV control unit, perform “READ CONFIGURATION” to save current vehicle specifi-

cation. Refer to 

AV-132, "CONFIGURATION (AV CONTROL UNIT) : Configuration List"

.

NOTE:

After the ignition switch is turned OFF, the AV control unit continues operating for approximately 30 seconds.

Therefore, data corruption may occur if battery voltage is cut off within 30 seconds. 
1. Disconnect the negative battery terminal. Refer to 

PG-78, "Removal and Installation (Battery)"

.

2. Remove cluster lid C. Refer to 

IP-22, "Removal and Installation"

.

3. Remove instrument finisher B. Refer to 

IP-16, "INSTRUMENT FINISHER B : Removal and Installation"

.

4. Remove instrument finisher E. Refer to 

IP-16, "INSTRUMENT FINISHER E : Removal and Installation"

.

5. Remove the AV control unit screws, then pull out the AV control unit.
6. Disconnect the harness connectors from the AV control unit and remove.
7. Remove the AV control unit bracket (LH/RH) screws and the AV control unit brackets (LH/RH) (if neces-

sary).

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

1.

AV control unit bracket (LH)

2.

AV control unit

3.

AV control unit bracket (RH)

AWNIA3339ZZ

AV-370

< REMOVAL AND INSTALLATION >

[NAVIGATION WITH BOSE]

AV CONTROL UNIT

• When replacing AV control unit, perform "WRITE CONFIGURATION". Refer to 

AV-281, "CONFIGURA-

TION (AV CONTROL UNIT) : Configuration List"

.

• When replacing AV control unit, the AV control unit must be registered. Refer to 

AV-282, "REGISTRA-

TION (AV CONTROL UNIT) : Description"

.

AV

STEERING SWITCH

AV-371

< REMOVAL AND INSTALLATION >

[NAVIGATION WITH BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

STEERING SWITCH

Exploded View

INFOID:0000000011277020

Removal and Installation

INFOID:0000000011277021

REMOVAL

NOTE:

The steering switches are serviced as an assembly.
1. Remove steering wheel. Refer to 

ST-11, "Removal and Installation"

.

2. Release pawls on the steering wheel rear finisher and remove.
3. Remove screws (A) and release pawls (B) and remove steering

switches (1) from steering wheel (2).
 : 

Pawls

INSTALLATION

Installation is in the reverse order of removal.

1.

Steering wheel rear finisher

2.

Steering wheel

3.

Steering switches

Pawl

AWNIA3722ZZ

AWNIA3723ZZ

 

 

 

 

 

 

 

Content   ..  92  93  94  95   ..