Nissan Rogue. Manual - part 84

AV-328

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

U1305 CONFIG UNFINISH

U1305 CONFIG UNFINISH

DTC Logic

INFOID:0000000011277000

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011277001

1.

PERFORM CONFIGURATION

When U1305 is detected, perform configuration of around view monitor control unit.

>> Refer to 

AV-281, "CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Pro-

cedure"

.

CONSULT Display

DTC Detection Condition

Possible Cause

Non-completion of the configu-
ration
[U1305]

Configuration of around view monitor control unit 
is incomplete.

Perform configuration of around view monitor 
control unit.

AV

U1310 CONTROL UNIT (AV)

AV-329

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U1310 CONTROL UNIT (AV)

DTC Logic

INFOID:0000000011277002

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause

CONTROL UNIT (AV)
[U1310]

Error during CAN controller hardware initializa-
tion (MCAN).

Replace AV control unit if malfunction occurs 
constantly.
Refer to 

AV-369, "Removal and Installation"

.

AV-330

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

AV CONTROL UNIT
AV CONTROL UNIT : Diagnosis Procedure

INFOID:0000000011277003

Regarding Wiring Diagram information, refer to 

AV-253, "Wiring Diagram"

.

1.

CHECK FUSE

Check that the following fuses are not blown:

Are the fuses blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect AV control unit connectors M108 and M109.

3. Check voltage between AV control unit connectors M108 and M109 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

CHECK GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Check continuity between AV control unit connector M108 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

BOSE SPEAKER AMP
BOSE SPEAKER AMP : Diagnosis Procedure

INFOID:0000000011277004

Regarding Wiring Diagram information, refer to 

AV-253, "Wiring Diagram"

.

1.

CHECK FUSE

Check that the following fuses are not blown:

Terminal No.

Signal name

Fuse No.

19

Battery power supply

16 (20A)

40

Ignition power supply

30 (10A)

AV control unit

Ground

Condition

Voltage

(Approx.)

Connector

Terminal

M108

19

—

Ignition switch: OFF

Battery voltage

M109

40

Ignition switch: ON

AV control unit

Ground

Continuity 

Connector

Terminal

M108

20

—

Yes

AV

POWER SUPPLY AND GROUND CIRCUIT

AV-331

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Are the fuses blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect Bose speaker amp. connector B137.

3. Check voltage between Bose speaker amp. connector B137 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

CHECK GROUND CIRCUIT

Check continuity between Bose speaker amp. connector B137 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure

INFOID:0000000011277005

Regarding Wiring Diagram information, refer to 

AV-253, "Wiring Diagram"

.

WITHOUT DRIVER ASSISTANCE SYSTEM

1.

CHECK FUSE

Check that the following fuses are not blown:

Are the fuses blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect around view monitor control unit connector M103.

3. Check voltage between around view monitor control unit connector M103 and ground.

Terminal No.

Signal name

Fuse No.

11

Battery power supply

11 (20A)

Bose speaker amp.

Ground

Condition

Voltage

(Approx.)

Connector

Terminal

B137

11

—

Ignition switch: OFF

Battery voltage

Bose speaker amp.

Ground

Continuity 

Connector

Terminal

B137

12

—

Yes

Terminal No.

Signal name

Fuse No.

2

Battery power supply

15 (20A)

Around view monitor control unit

Ground

Condition

Voltage

(Approx.)

Connector

Terminal

M103

2

—

Ignition switch: OFF

Battery voltage