Nissan Rogue. Manual - part 38

AV-144

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITHOUT BOSE]

U111A REAR CAMERA IMAGE SIGNAL CIRCUIT

U111A REAR CAMERA IMAGE SIGNAL CIRCUIT

DTC Logic

INFOID:0000000011276833

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011276834

Regarding Wiring Diagram information, refer to 

AV-107, "Wiring Diagram"

.

1.

CHECK REAR VIEW CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect around view monitor control unit and rear view camera connectors.

3. Check continuity between around view monitor control unit connector M114 and rear view camera con-

nector D514.

4. Check continuity between around view monitor control unit connector M114 and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness or connectors.

2.

CHECK REAR VIEW CAMERA POWER SUPPLY VOLTAGE

1. Connect around view monitor control unit and rear view camera connectors.

2. Turn ignition switch ON.

3. Check voltage between around view monitor control unit connector M114 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace around view monitor control unit. Refer to 

AV-208, "Removal and Installation"

.

3.

CHECK REAR VIEW CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect around view monitor control unit and rear view camera connectors.

3. Check continuity between around view monitor control unit connector M114 and rear view camera con-

nector D514.

CONSULT Display

DTC Detection Condition

Possible Cause

Rear display output signal diag-
nosis (Harness disconnection)
[U111A]

Rear view camera image signal circuit open or 
short.

Check rear view camera image signal circuit.

Around view monitor control unit

Rear view camera

Continuity

Connector

Terminals

Connector

Terminals

M114

50

D514

8

Yes

52

7

Around view monitor control unit

Ground

Continuity

Connector

Terminal

M114

50

No

Around view monitor control unit

Ground

Condition

Voltage

(Approx.)

Connector

Terminal

M114

50

—

CAMERA switch is ON or 
selector lever in R (re-
verse).

6.0 V

AV

U111A REAR CAMERA IMAGE SIGNAL CIRCUIT

AV-145

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITHOUT BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

4. Check continuity between around view monitor control unit connector M114 and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connectors.

4.

CHECK REAR VIEW CAMERA IMAGE SIGNAL

1. Connect around view monitor control unit and rear view camera connectors.

2. Turn ignition switch ON.

3. Check signal between the terminals of around view monitor control unit connector M114.

Is the inspection result normal?

YES

>> Replace around view monitor control unit. Refer to 

AV-208, "Removal and Installation"

.

NO

>> Replace rear view camera. Refer to 

AV-211, "Removal and Installation"

.

Around view monitor control unit

Rear view camera

Continuity

Connector

Terminals

Connector

Terminals

M114

53

D514

5

Yes

54

1

Around view monitor control unit

Ground

Continuity

Connector

Terminal

M114

53

No

Around view monitor control unit connector M114

Condition

Reference value

(+)

(

−)

Terminal

Terminal

53

54

CAMERA switch is ON or se-
lector lever in R (reverse).

JSNIA0834GB

AV-146

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITHOUT BOSE]

U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT

U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT

DTC Logic

INFOID:0000000011276835

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011276836

Regarding Wiring Diagram information, refer to 

AV-107, "Wiring Diagram"

.

1.

CHECK RH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect around view monitor control unit and RH side camera connectors.

3. Check continuity between around view monitor control unit connector M114 and RH side camera connec-

tor D107.

4. Check continuity between around view monitor control unit connector M114 and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness or connectors.

2.

CHECK RH SIDE CAMERA POWER SUPPLY VOLTAGE

1. Connect around view monitor control unit and RH side camera connectors.

2. Turn ignition switch ON.

3. Check voltage between around view monitor control unit connector M114 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace around view monitor control unit. Refer to 

AV-208, "Removal and Installation"

.

3.

CHECK RH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect around view monitor control unit and RH side camera connectors.

CONSULT Display

DTC Detection Condition

Possible Cause

Right side display output signal 
diagnosis (Harness disconnec-
tion)
[U111B]

Right side camera image signal circuit open or 
short.

Check right side camera image signal circuit.

Around view monitor control unit

RH side camera

Continuity

Connector

Terminals

Connector

Terminals

M114

62

D107

7

Yes

64

8

Around view monitor control unit

Ground

Continuity

Connector

Terminal

M114

62

No

Around view monitor control unit

Ground

Condition

Voltage

(Approx.)

Connector

Terminal

M114

62

—

CAMERA switch is ON or 
selector lever in R (re-
verse).

6.0 V

AV

U111B SIDE CAMERA RH IMAGE SIGNAL CIRCUIT

AV-147

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITHOUT BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

3. Check continuity between around view monitor control unit connector M114 and RH side camera connec-

tor D107.

4. Check continuity between around view monitor control unit connector M114 and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connectors.

4.

CHECK RH SIDE CAMERA IMAGE SIGNAL

1. Connect around view monitor control unit and RH side camera connectors.

2. Turn ignition switch ON.

3. Check signal between the terminals of around view monitor control unit connector M114.

Is the inspection result normal?

YES

>> Replace around view monitor control unit. Refer to 

AV-208, "Removal and Installation"

.

NO

>> Replace RH side camera. Refer to 

AV-210, "Removal and Installation"

.

Around view monitor control unit

RH side camera

Continuity

Connector

Terminals

Connector

Terminals

M114

65

D107

16

Yes

66

15

Around view monitor control unit

Ground

Continuity

Connector

Terminal

M114

65

No

Around view monitor control unit connector M114

Condition

Reference value

(+)

(

−)

Terminal

Terminal

65

66

CAMERA switch is ON or se-
lector lever in R (reverse).

JSNIA0834GB