Nissan Leaf. Manual - part 207

C1A6D BRAKE POWER SUPPLY BACKUP UNIT

BR-149

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6D” detected?

YES

>> GO TO 15.

NO

>> INSPECTION END

15.

CHECK BRAKE POWER SUPPLY BACKUP UNIT CIRCUIT

1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

3. Disconnect 12V battery cable from negative terminal. Refer to 

BR-6, "Precaution for Removing 12V Bat-

tery"

.

4. Disconnect the electrically-driven intelligent brake unit harness connector.

5. Disconnect the brake power supply backup unit harness connector.

6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

7. Check the continuity between brake power supply backup unit and ground.

Is the inspection result normal?

YES

>> Replace the brake power supply backup unit. Refer to 

BR-513, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

Electrically-driven intelligent brake unit

Brake power supply backup unit

Continuity

Connector

Terminal

Connector

Terminal

E34

31

B15

1

Existed

31

4

Not existed

31

5

Not existed

31

6

Not existed

Brake power supply backup unit

—

Continuity

Connector

Terminal

B15

1

Ground

Not existed

BR-150

< DTC/CIRCUIT DIAGNOSIS >

C1A6E EV SYSTEM

C1A6E EV SYSTEM

DTC Logic

INFOID:0000000010123025

DTC DETECTION LOGIC

DTC REPRODUCTION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn power switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6E” detected?

YES

>> Proceed to 

BR-150, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010123026

1.

PERFORM VCM SELF DIAGNOSIS

Start CONSULT and perform self-diagnosis for “EV/HEV”. Refer to 

EVC-72, "CONSULT Function"

.

Is any DTC detected?

YES

>> Check the DTC. Refer to 

EVC-102, "DTC Index"

.

DTC

Display item

Malfunction detection condition

Possible causes

C1A6E

EV/HEV SYSTEM

Malfunction is detected in the VCM system.

• Harness or connector
• VCM
• Electrically-driven intelligent 

brake unit

C1A6E EV SYSTEM

BR-151

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6E” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK 12V BATTERY

1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

3. Check the 12V battery terminal connections. Refer to 

BR-6, "Precaution for Removing 12V Battery"

 and

PG-83, "Work Flow"

.

4. Check the 12V battery. Refer to 

PG-83, "Work Flow"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts and GO TO 4.

4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

1. Connect 12V battery cable to negative terminal.

2. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

3. Repeat step 2 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

4. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

5. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

BR-152

< DTC/CIRCUIT DIAGNOSIS >

C1A6E EV SYSTEM

Never operate the vehicle while waiting.

6. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

7. Start CONSULT and erase self-diagnosis result of “BRAKE”.

8. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

9. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

10. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

11. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

12. Release brake pedal.

13. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6E” detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

CHECK CONNECTOR TERMINALS

1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

3. Disconnect 12V battery cable from negative terminal. Refer to 

BR-6, "Precaution for Removing 12V Bat-

tery"

.

4. Disconnect the electrically-driven intelligent brake unit harness connector, then check for failures of pin

terminals and connections.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace error-detected parts and GO TO 6.

6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

7. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

8. Start CONSULT and erase self-diagnosis result of “BRAKE”.

9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

11. Turn the power switch ON without depressing the brake pedal.

CAUTION: