Nissan Primera P11. Manual - part 67

 

  Index      Nissan     Nissan Primera P11 (2001 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  65  66  67  68   ..

 

 

Nissan Primera P11. Manual - part 67

 

 

REMOVAL

After removing moldings, remove glass using piano wire or
power cutting tool and inflatable pump bag.

WARNING:

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edges. Small chips
may develop into cracks.

INSTALLATION

Use a genuine Nissan Urethane Adhesive Kit or equivalent
and follow the instructions furnished with it.

While the urethane adhesive is curing, open a door window.
This will prevent the glass from being forced out by passen-
ger compartment air pressure when a door is closed.

The molding must be installed securely so that it is in posi-
tion and leaves no gap.

Inform the customer that the vehicle should remain station-
ary until urethane adhesive has completed cured (preferably
24 hours). Curing time varies with temperature and humidity.

WARNING:

Keep heat and open flames away as primers and adhesive
are flameable.

The materials contained in the kit are harmful if swallowed,
and may irritate skin and eyes.

Use in an open , well ventilated location. Avoid breathing the
vapors. They can be harmful if inhaled. If affected by vapor
inhalation, immediately move to an area with fresh air.

Driving the vehicle before the urethane adhesive has com-
pletely cured may affect the performance of the windshield in
case of an accident.

CAUTION

Do not use an adhesive which is past its usable term. Shelf
life of this product is limited to six months after the date of
manufacture. Carefully adhere to expiration or manufacture
date printed on the box.

Keep primers and adhesive in a cool, dry place. Ideally, they
should be stored in a refrigerator.

Do not leave primers and adhesive cartridge unattended with
their caps open or off.

The vehicle should not be driven for at least 24 hours or until
the urethane adhesive has completely cured. Curing times
varies depending on temperature and humidities. The curing
time will increase under higher temperatures lower humidi-
ties.

SBF034B

Cutting sealant

Glass

SBT472

Windshield glass

Interior auto glass
cut-out knife kit

SBT473

Windshield
glass

Inflatable
pump bag

WINDSHIELD AND WINDOWS

BT-53

Windshield and Rear Window

REPAIRING WATER LEAKS FOR WINDSHIELD

Leaks can be repaired without removing and reinstalling glass.
If water is leaking between caulking material and body or glass, determine the extent of leakage. This
can be determined by applying water while pushing glass outward.
To stop the leak, apply primer (if necessary) and then sealant to the leak point.

YBT033

Body side

SBF017A

Glass side

YBT034

Windshield
Install spacer to panel

Cowl top

Glass

Spacer

455.4 mm (17.93 in)

Install dam rubber.
Windshield and
rear window

8 (0.31)

Vehicle center

joint portion

Apply sealant evenly

12

-

1

5

(0.47

-

0.59)

Dam rubber

Glass

Unit: mm (in)

7 - 8 (0.28 - 0.31)

8 (0.31)

8 (0.31)

Install molding fastener.

When installing it, heat body panel and fastener to
approx. 30 to 40°C (86 to 104°F).

Windshield

Upper & side molding fasteners

Fastener

Panel

Double-faced
adhesive tape

Rear window

WINDSHIELD AND WINDOWS

BT-54

Side Window

Primer portion

Sealing portion and installation

NBF283

Body side

.

A

A

B

B

Primer
portion

A-A

B-B

Primer
portion

Primer
portion

Glass side

A

A

Window glass

B

Primer portion

Primer portion

A-A

Glass

B-B

Glass

Primer
portion

B

D

D

A

A

B

B

Clip
(bonded on
glass)

C-C

Glass

Clip
(bonded on
glass)

Glass

D-D

More than
7 (0.28)

More than
8 (0.32)

Glass

Molding

Apply sealant evenly

Unit: mm (in)

More than
7 (0.28)

More than
8 (0.32)

Glass

NBF281

WINDSHIELD AND WINDOWS

BT-55

Back Door Window

Construction and removal/reinstallation method of back door window are basically the same as those of
windshield.

5-door hatchback

For details of moldings, refer to “EXTERIOR”, BT-31.

YBT035

Primer portion (Body side)

Primer

Primer

30 (1.18)

Primer

Sealant quantity

12 - 15
(0.47 - 0.59)

7 - 8
(0.28 - 0.31)

33 (1.30)

33 (1.30)

8.75
(0.3445)

18.4
(0.724)

41.2
(1.622)

28 (1.10) 41 (1.61) 33 (1.30)

400 (15.75)

Sealant portion (Body side)

Primer portion (Glass side)

Dam rubber portion (Glass side)

Back door molding

Dam rubber

Primer

Back door molding

Back door molding

Primer

Back door molding

Primer

Unit: mm (in)

WINDSHIELD AND WINDOWS

BT-56

 

 

 

 

 

 

 

Content   ..  65  66  67  68   ..