Nissan Pathfinder. Manual - part 41

ADP-156

< DTC/CIRCUIT DIAGNOSIS >

DOOR MIRROR MOTOR

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace automatic drive positioner control unit. Refer to 

ADP-162, "Removal and Installation"

.

4.

 CHECK DOOR MIRROR MOTOR

Check door mirror motor.

Refer to 

ADP-156, "Component Inspection"

.

Is the inspection result normal?

YES

>> Refer to 

GI-49, "Intermittent Incident"

.

NO

>> Replace door mirror actuator. Refer to 

MIR-20, "Removal and Installation"

.

Component Inspection

INFOID:0000000009176665

1.

 CHECK DOOR MIRROR MOTOR-I

Check that door mirror motor does not trap foreign objects and does not have any damage.

Refer to 

MIR-17, "Exploded View"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace door mirror actuator. Refer to 

MIR-20, "Removal and Installation"

.

2.

 CHECK DOOR MIRROR MOTOR-II

1. Turn ignition switch OFF.

2. Disconnect door mirror.

3. Apply 12V to each power supply terminal of door mirror motor.

With around view monitor system

Without around view monitor system

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace door mirror actuator. Refer to 

MIR-20, "Removal and Installation"

.

M33

10

Ground

UP

Battery voltage

Other than above

0

11

LEFT

Battery voltage

Other than above

0

22

DOWN / RIGHT

Battery voltage

Other than above

0

Door mirror connector

Terminal

Operational direction

(+)

(–)

D28 (LH)

D128 (RH)

10

11

RIGHT

11

10

LEFT

12

10

UP

10

12

DOWN

Door mirror connector

Terminal

Operational direction

(+)

(–)

D4 (LH)

D107 (RH)

10

9

RIGHT

9

10

LEFT

8

10

UP

10

8

DOWN

SEAT MEMORY INDICATOR

ADP-157

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SEAT MEMORY INDICATOR

Description

INFOID:0000000009176666

• Memory switch is equipped on the seat memory switch installed to the driver side door trim. The operation

signal is input to the driver seat control unit when the memory switch is operated.

• The status of automatic drive positioner system can be checked according to the illuminating/flashing status.

Component Function Check

INFOID:0000000009176667

1.

 CHECK FUNCTION

1. Select “MEMORY SW INDCTR” in “ACTIVE TEST” mode with CONSULT. 

2. Check the memory indicator operation.

Is the operation of relevant parts normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to 

ADP-157, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009176668

Regarding Wiring Diagram information, refer to 

ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"

or 

ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"

.

1.

 CHECK SEAT MEMORY INDICATOR CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect driver seat control unit and seat memory switch.

3. Check continuity between driver seat control unit harness connector and seat memory switch harness

connector.

4. Check continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

 CHECK MEMORY INDICATOR POWER SUPPLY

Check voltage between seat memory switch harness connector and ground.

Test item

Description

MEMORY SW INDCTR

OFF

Memory switch indicator

OFF

ON-1

Indicator 1: ON

ON-2

Indicator 2: ON

Driver seat control unit

Seat memory switch

Continuity

Connector

Terminal

Connector

Terminal

B209

10

D60

13

Yes

26

14

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B209

10

No

26

ADP-158

< DTC/CIRCUIT DIAGNOSIS >

SEAT MEMORY INDICATOR

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check the following:

• 10A fuse no.1.

• Harness for open or short between memory indicator and fuse.

3.

 CHECK MEMORY INDICATOR

Refer to 

ADP-158, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace seat memory switch. Refer to 

ADP-163, "Removal and Installation"

.

4.

 CHECK INTERMITTENT INCIDENT

Refer to 

GI-49, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace driver seat control unit. Refer to 

ADP-161, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning part.

Component Inspection

INFOID:0000000009176669

1.

 CHECK SEAT MEMORY INDICATOR

1. Disconnect seat memory switch.

2. Check continuity between seat memory switch terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace seat memory switch. Refer to 

ADP-163, "Removal and Installation"

.

(+)

(–)

Voltage (V) 

(Approx.)

Seat memory switch

Connector

Terminals 

D60

15

Ground

Battery voltage

Terminal

Continuity

Seat memory switch

(+)

(-)

15

13

Yes

14

ADP SYSTEM SYMPTOMS

ADP-159

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SYMPTOM DIAGNOSIS

ADP SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000009176670

NOTE:

 Always perform the “Basic Inspection” before performing diagnosis in the following table. Refer to 

ADP-69,

"Work Flow"

.

Symptom

Diagnosis procedure

Reference page

Manual functions (for specific part) do 
not operate.

Sliding operation

Check sliding switch. 

ADP-91

Reclining operation

Check reclining switch.

ADP-94

Lifting operation (front) 

Check lifting switch (front).

ADP-97

Lifting operation (rear) 

Check lifting switch (rear).

ADP-100

Tilt operation (if equipped) Check tilt switch.

ADP-103

Telescopic sensor (if 
equipped)

Check telescopic switch.

ADP-105

Door mirror operation

1. Changeover switch.

ADP-110

2. Mirror switch

ADP-112

All parts of seat

Check power seat switch ground cir-
cuit.

ADP-115

Memory functions (for specific part) do 
not operate.

Sliding operation

Check sliding sensor.

ADP-117

Reclining operation

Check reclining sensor.

ADP-120

Lifting operation (front) 

Check lifting sensor (front).

ADP-123

Lifting operation (rear) 

Check lifting sensor (rear).

ADP-126

Tilt operation (if equipped) Check tilt sensor.

ADP-129

Telescopic operation (if 
equipped)

Check telescopic sensor.

ADP-132

Door mirror operation

Check door mirror sensor.

Driver side: 

ADP-135

Passenger side:

ADP-137

Memory functions and manual functions 
(for specific part) do not operate.

Sliding operation

Check sliding motor LH. 

ADP-140

Reclining operation

Check reclining motor LH.

ADP-142

Lifting operation (front) 

Check lifting motor LH (front).

ADP-144

Lifting operation (rear) 

Check lifting motor LH (rear).

ADP-146

Tilt operation (if equipped) Check tilt motor.

ADP-148

Telescopic operation (if 
equipped)

Check telescopic motor.

ADP-150

Door mirror operation

Check door mirror motor.

ADP-152

Entry/Exit assist function does not operate.

1. Check system setting.

ADP-12

2. Perform initialization.

ADP-73

3. Check front door switch (driver side).

DLK-170

Intelligent Key interlock function does not operate.
(Other automatic operations and Intelligent Key system are normal)

1. Check door lock function.

DLK-20

2. Perform memory storing.

ADP-74