Nissan Teana J32. Manual - part 1077

SRC-62

< COMPONENT DIAGNOSIS >

B1087 PRE-TEN FRONT LH

B1087 PRE-TEN FRONT LH

Description

INFOID:0000000003814002

For front LH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and safing algorithm in
front direction.

OPERATION

In the case of a frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects
the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003814003

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-10, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-62, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003814004

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1087

PRE-TEN FRONT LH
[VB-SHORT]

Front LH seat belt pre-tensioner circuit 
is shorted to some power supply circuit

• Disconnection of wiring harness and 

short

• Malfunction in front LH seat belt pre-

tensioner

• Malfunction in air bag diagnosis sen-

sor unit

B1087 PRE-TEN FRONT LH

SRC-63

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE FRONT SEAT BELT PRE-TENSIONER

1.

Replace front LH seat belt pre-tensioner. Refer to 

SB-5, "SEAT BELT RETRACTOR : Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT 

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-22, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-64

< COMPONENT DIAGNOSIS >

B1088 PRE-TEN FRONT LH

B1088 PRE-TEN FRONT LH

Description

INFOID:0000000003814005

For front LH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and safing algorithm in
front direction.

OPERATION

In the case of a frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects
the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003814006

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-10, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-64, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003814007

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1088

PRE-TEN FRONT LH 
[GND-SHORT]

Front LH seat belt pre-tensioner circuit 
is shorted to ground

• Disconnection of wiring harness and 

short

• Malfunction in front LH seat belt pre-

tensioner

• Malfunction in air bag diagnosis sen-

sor unit

B1088 PRE-TEN FRONT LH

SRC-65

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE FRONT SEAT BELT PRE-TENSIONER

1.

Replace front LH seat belt pre-tensioner. Refer to 

SB-5, "SEAT BELT RETRACTOR : Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-64, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT 

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-22, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-64, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END