Nissan Juke F15. Manual - part 401

 

  Index      Nissan     Nissan Juke F15 (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  399  400  401  402   ..

 

 

Nissan Juke F15. Manual - part 401

 

 

P0605 ECM

EC-417

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0605 ECM

DTC Logic

INFOID:0000000012197958

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON (engine stopped) and wait least 20 minutes.

CAUTION:

Never start engine during this procedure.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-417, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197959

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-417, "DTC Logic"

.

Is the 1st trip DTC P0605 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0605

ECM
[Internal control module 
read only memory (ROM) 
error]

Malfunction in the internal ROM of ECM.

ECM

EC-418

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P0606 ECM

P0606 ECM

DTC Logic

INFOID:0000000012197960

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-I

1. Turn ignition switch ON (engine stopped) and wait at least 10 seconds.

CAUTION:

Never start engine during this procedure.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-418, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE-II

1. Start engine.

2. Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release

the accelerator pedal.

3. Let the engine idle and wait at least 10 seconds.

4. Turn ignition switch OFF and wait at least 10 seconds.

5. Turn ignition switch ON.

6. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-418, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197961

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure for 3 times. Refer to 

EC-418, "DTC Logic"

.

Is the 1st trip DTC P0606 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0606

CONTROL MODULE
(Control module processor)

Malfunction in ECM processor.

ECM

P0607 ECM

EC-419

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0607 ECM

DTC Logic

INFOID:0000000012197962

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON (engine stopped) and wait least 10 seconds.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-419, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197963

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-419, "DTC Logic"

.

Is the 1st trip DTC P0607 displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0607

ECM
(Control module perfor-
mance)

ECM internal communication system is malfunc-
tioning.

ECM

EC-420

< DTC/CIRCUIT DIAGNOSIS >

[MR FOR NISMO RS MODELS]

P060A ECM

P060A ECM

DTC Logic

INFOID:0000000012197964

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition

switch ON.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and wait at least 10 seconds.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Repeat step 1 and 2 for 5 times.

4. Turn ignition switch ON.

5. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Proceed to 

EC-420, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012197965

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Erase DTC.

3. Perform DTC confirmation procedure. Refer to 

EC-420, "DTC Logic"

.

Is the 1st trip DTC P060A displayed again?

YES

>> Replace ECM. Refer to 

EC-590, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P060A

CONTROL MODULE
(Internal control module 
monitoring processor per-
formance)

ECM internal monitoring processor is malfunction-
ing.

ECM

 

 

 

 

 

 

 

Content   ..  399  400  401  402   ..