Nissan Juke F15. Manual - part 265

P1832 TCS OPERATION SIGNAL

DLN-65

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P1832 TCS OPERATION SIGNAL

DTC Logic

INFOID:0000000012199411

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1832” detected?

YES

>> Proceed to 

DLN-65, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199412

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 2.

2.

ERASE SELF-DIAGNOSTIC RESULT

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.

3. Stop the vehicle.

4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> Refer to 

BRC-136, "Component Function Check"

.

3.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1832”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1832

TCS OP SIG

Malfunction is detected in TCS operation 
signal that is output from ABS actuator 
and electric unit (control unit) through 
CAN communication.

• ABS actuator and electric unit (control 

unit)

• AWD control module
• CAN communication line

DLN-66

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P183B SOLENOID POWER SUPPLY

P183B SOLENOID POWER SUPPLY

DTC Logic

INFOID:0000000012199413

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183B” detected?

YES

>> Proceed to 

DLN-66, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199414

1.

CHECK AWD SOLENOID POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Disconnect AWD control module harness connector.

3. Check the voltage between AWD control module harness connector and ground.

4. Turn the ignition switch OFF to ON.

CAUTION:

Never start the engine.

5. Check the voltage between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK AWD SOLENOID POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (#12).

DTC

Display item

Malfunction detected condition

Possible cause

P183B

SOL POWER SUPPLY

When AWD solenoid power supply volt-
age is lower or higher than normal.

• Malfunction of AWD solenoid power 

supply circuit 

• Malfunction of AWD control module
• Malfunction of AWD control module 

power supply circuit (open or short)

• Battery

AWD control module

—

Voltage

Connector

Terminal

B47

12

Ground

11 – 13 V

AWD control module

—

Voltage

Connector

Terminal

B47

12

Ground

11 – 13 V

P183B SOLENOID POWER SUPPLY

DLN-67

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

3. Check the harness for open or short between AWD control module harness connector No.12 and the 10A

fuse (#12).

Is the inspection result normal?

YES

>> Perform the trouble the diagnosis for power supply circuit. Refer to 

PG-12, "Wiring Diagram -

BATTERY POWER SUPPLY -"

.

NO

>> Repair or replace error-detected parts.

3.

CHECK AWD CONTROL MODULE POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Check the voltage between AWD control module harness connector and ground.

3. Turn the ignition switch ON.

CAUTION:

Never start the engine.

4. Check the voltage between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK AWD CONTROL MODULE POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (#3).

3. Check the harness for open or short between AWD control module harness connector No.3 terminal and

10A fuse (#3).

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for ignition power supply circuit. Refer to 

PG-43, "Wiring Diagram -

IGNITION POWER SUPPLY -"

.

NO

>> Repair or replace error-detected parts.

5.

CHECK AWD SOLENOID GROUND

Check the continuity between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the error-detected parts.

6.

CHECK TERMINALS AND HARNESS CONNECTORS

1. Check AWD control module pin terminals for damage or loose connection with harness connector.

2. Check AWD solenoid pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace the error-detected parts.

AWD control module

—

Voltage

Connector

Terminal

B47

3

Ground

0 V

AWD control module

—

Voltage

Connector

Terminal

B47

3

Ground

11 – 13 V

AWD control module

—

Continuity

Connector

Terminal

B47

10

Ground

Existed

11

DLN-68

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P183C DECEL G SENSOR

P183C DECEL G SENSOR

DTC Logic

INFOID:0000000012199415

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183C” detected?

YES

>> Proceed to 

DLN-68, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199416

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

BRC-50, "DTC Index"

.

NO

>> GO TO 2.

2.

ERASE SELF-DIAGNOSTIC RESULT

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

3. Stop the vehicle.

4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?

YES

>> GO TO 3.

NO

>> Refer to 

BRC-136, "Component Function Check"

.

3.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183C”

is detected, Replace AWD control module. Refer to 

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P183C

DECEL G SENSOR

Malfunction is detected in decel G sen-
sor signal that is output from ABS actua-
tor and electric unit (control unit) through 
CAN communication.

• ABS actuator and electric unit (control 

unit)

• Yaw rate/side/decel G sensor (Decel 

G sensor signal)

• AWD  control  module
• CAN communication line