Nissan Tiida C11. Manual - part 1175

SEC-72

< ECU DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

INTELLIGENT KEY UNIT

B2552: INTELLIGENT KEY

Intelligent Key unit internal malfunction.

×

Replace Intelligent Key 
unit.

B2590: NATS MALFUNCTION

The ID verification result between Intelligent key 
unit and BCM are NG. Or Intelligent Key unit cannot 
communicate with BCM.

×

Check NATS
Refer to 

SEC-35

CONSULT display

Detection condition

Fail-safe

Diagnosis

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

SEC-73

< ECU DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)

Reference Value

INFOID:0000000001404135

Refer to IPDM E/R.

Fail Safe

INFOID:0000000001404139

CAN communication control

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.

If no CAN communication is available with ECM

*1: HR engine models

*2: MR engine and K9K engine models

If no CAN communication is available with BCM

Ignition relay malfunction detection function

• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it. 
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation

coil circuit.

• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to

alert the user to the ignition relay malfunction when the ignition switch is turned OFF.

Control part

Fail-safe in operation

Cooling fan

• The cooling fan relay-2*

1

 or the cooling fan relay-3*

2

 turns ON when the ignition switch 

is turned ON

• Turns off the fan motor low relay when the ignition switch is turned OFF

A/C compressor

A/C relay OFF

Control part

Fail-safe in operation

Headlamp

• The headlamp low relay turns ON when the ignition switch is turned ON
• The headlamp low relay turns OFF when the ignition switch is turned OFF
• Headlamp high relay OFF

• Parking  lamps
• License plate lamps
• Tail lamps
• Illuminations

• The tail lamp relay turns ON when the ignition switch is turned ON
• The tail lamp relay turns OFF when the ignition switch is turned OFF

Front wiper

• The status just before activation of fail-safe control is maintained until the ignition 

switch is turned OFF while the front wiper is operating at LO or HI speed.

• The front wiper is operated at LO speed until the ignition switch is turned OFF if the 

fail-safe control is activated while the front wiper is set in the INT mode and the front 
wiper motor is operating.

Front fog lamps

Front fog lamp relay OFF

Starter motor

Inhibit relay OFF

Rear window defogger

Rear window defogger relay OFF

Headlamp washer

Headlamp washer relay OFF

PTC heater

PTC heater relay OFF

DTC

Ignition switch

Ignition relay

Tail lamp relay

—

ON

ON

—

—

OFF

OFF

—

B2098: IGN RLY ON

OFF

ON

ON (10 minutes)

B2099: IGN RLY OFF

ON

OFF

—

SEC-74

< ECU DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

NOTE:

The tail lamp relay is turned OFF when the ignition switch is turned ON.

Front wiper control

IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop five times.

NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.

DTC Index

INFOID:0000000001404140

NOTE:

The details of time display are as follows.

• CRNT: The malfunctions that are detected now.

• PAST: The number is indicated when it is normal at present and a malfunction was detected in the past.

Ignition switch

Front wiper switch

Front wiper auto stop signal

ON

OFF

The front wiper auto stop signal (stop posi-
tion) cannot be input for 10 seconds.

ON

The front wiper auto stop signal does not 
change for 10 seconds.

CONSULT display

Fail-safe

Timing

NOTE

Reference page

No DTC is detected.
further testing
may be required.

—

—

—

—

U1000: CAN COMM CIRCUIT

×

CRNT

PAST

XX-XX, "*****"

B2098: IGN RELAY ON

×

CRNT

PAST

XX-XX, "*****"

B2099: IGN RELAY OFF

—

CRNT

PAST

XX-XX, "*****"

B2100: EEPROM

—

CRNT

PAST

XX-XX, "*****"

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION SYMPTOMS

SEC-75

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SYMPTOM DIAGNOSIS

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION SYMPTOMS

Symptom Table

INFOID:0000000001404141

NOTE:
• Before performing the diagnosis in the following table, check “

XX-XX, "*****"

”. 

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column

in this order.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Engine start function is ON when setting on CONSULT-III.
• Mechanical key is not inserted in key cylinder.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.

Symptom

Diagnosis/service procedure

Reference 

page

Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (green) illuminates.]

1.

Check steering lock unit.

SEC-23

2.

Replace Intelligent Key unit.

XX-XX, 

"*****"

Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp does not illuminate.]

1.

Check Intelligent Key unit power supply and ground cir-
cuit.

XX-XX, 

"*****"

2.

Check ignition knob switch.

XX-XX, 

"*****"

3.

Check key switch.

XX-XX, 

"*****"

4.

Replace Intelligent Key unit.

XX-XX, 

"*****"

Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (red) illuminates.]

1.

Check inside key antenna.

XX-XX, 

"*****"

2.

Replace Intelligent Key unit.

XX-XX, 

"*****"

Ignition switch does not turn on with mechanical key

Check key switch.

XX-XX, 

"*****"

Engine cannot start

1.

Check key switch.

XX-XX, 

"*****"

2.

Check stop lamp switch (A/T).

XX-XX, 

"*****"

3.

Check stop lamp switch (M/T).

XX-XX, 

"*****"