Mitsubishi Outlander XL. Manual - part 833

KEYLESS ENTRY SYSTEM CHECK

M14209200049USA0000010000

Check the keyless entry system function as described below. If
it does not work, perform troubleshooting. Refer to P.42C-66.

｠

Operate the transmitter to check that the doors and liftgate can
be locked and unlocked.

｠

Operate the transmitter to check that the answerback function
works in response to door and liftgate locking/unlocking.

NOTE:

The hazard and horn answerback setting can be

changed using the customization function. Confirm which
setting is activated before performing these checks.
Refer to P.42C-91.

INSPECTION OF KEYLESS ENTRY TIMER LOCK

FUNCTION

M14209200051USA0000010000

Attempt to unlock the doors and the liftgate by using the
transmitter. If the doors and the liftgate are not locked within 30
seconds, carry out diagnosis. Note that the doors and the liftgate
will not be locked if the ignition key is inserted within the 30-
second period, one of the doors or the liftgate is opened. Refer
to P.42C-66.

NOTE:

The operation time of the keyless entry timer lock

function can be set using the customization function.
Confirm the operation time before performing the diagnosis.
Refer to P.42C-91.

CONFIGURATION FUNCTION

M14209200052USA0000010000

Using M.U.T.-III, the following functions can be
customized. The programmed information is held
even when the battery is disconnected.

Adjustment
item (scan tool
MB991958
display)

Adjustment item

Adjusting

contents

(scan tool MB991958
display)

Adjusting contents

Hazard answer
back

Adjustment of the
number of keyless
hazard warning light
answer

back

flashes

Lock:1, Unlock:2

LOCK: Flashes once, UNLOCK: Flashes
twice (default)

Lock:1, Unlock:0

LOCK: Flashes once, UNLOCK: No flash

Lock:0, Unlock:2

LOCK: No flash, UNLOCK: Flash twice

Lock:2, Unlock:1

LOCK: Flash twice, UNLOCK: Flash once

Lock:2, Unlock:0

LOCK: Flash twice, UNLOCK: No flash

Lock:0, Unlock:1

LOCK: No flash, UNLOCK: Flash once

Lock:0, Unlock:0

Without function

Dome

light

delay timer with
door

Adjustment

interior light delay
shutdown time

0sec

0 second (no delay shutdown time)

7.5sec

7.5 seconds

WIRELESS CONTROL MODULE (WCM)

42C-91

ON-VEHICLE SERVICE

Adjustment
item (scan tool
MB991958
display)

Adjustment item

Adjusting

contents

(scan tool MB991958
display)

Adjusting contents

15sec

15 seconds

30sec

30 seconds (default)

60sec

60 seconds

120sec

120 seconds

180sec

180 seconds

Door

unlock

mode

Door lock system

All doors unlock

All the doors are unlocked when the driver's
side door is unlocked.

Dr door unlock

Only the driver's side door is unlocked when
the driver's side door is unlocked. (default)

Auto

door

unlock by P
position

Auto door unlock by
P position function

Disable

Without function (default)

Always enabled

Always with function

P/W unlocked

With function (with power window
unlocked)

Duration of horn
chirp

Horn sounding time
during horn answer
back

Short

0.01 second (default)

Long

0.02 second

Horn chirp by
RKE

Horn chirp by RKE

Not sound horn

No horn answerback function

Lock any time

The horn sounds when the lock button of
keyless entry transmitter is pressed once.

W lock any time

The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(default)

Timer lock timer Timer lock period

adjustment

30sec

30 seconds (default)

60sec

60 seconds

120sec

120 seconds

180sec

180 seconds

Duration

pre-

alarm

Adjustment of pre-
alarm continue time

10 sec

10 seconds (default)

6 sec

6 seconds

Alarm

With/without theft-
alarm function

Disable

Without function

Enable

With function (default)

Panic

alarm

switch

With/without panic
alarm function

Disable

Without function

Enable

With function (default)

TIRE PRESSURE SENSOR ID REGISTRATION

M14209200068USA0000010000

When the TPMS transmitter and/or WCM are replaced, execute
"Tire Pressure Sensor ID Registration." The TPMS won't
function until the "Tire Pressure Sensor ID Registration" has
been complete.

42C-92

WIRELESS CONTROL MODULE (WCM)

ON-VEHICLE SERVICE

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "Interactive Diagnosis" from the start-up screen.

Select "System select."

Select "Special Function."

Select "Tire Pressure Sensor ID Registration."

Select "4tires ID Reg. (Change tire PRS.)" and start the tire
pressure sensor ID registration.

Register all tire pressure sensor IDs within twenty minutes.

"4 SNSR ID Registration Do you want to start? Note Finish ID
Registration within 20 minutes." is displayed. Then, press
"OK."

Decrease the tire pressure to 174 kPa or less, and register the
TPMS transmitter ID code of each wheel to WCM.

NOTE:

｠

On completion of the TPMS transmitter ID code registration,
the TPMS transmitter ID code is displayed on the M.U.T.-III
screen.

｠

It may take approximately one minute for the ID code to be
displayed on the M.U.T.-III screen after the tire pressure is
reduced.

｠

If the ID code is not displayed, reduce the tire pressure
another 20 kPa or more. If the ID code is not displayed yet,
rotate the tire to displace the TPMS transmitter, and reduce
the tire pressure 20 kPa or more again.

｠

You can start out the following operations from any TPMS
transmitter. The tire pressure sensor ID registration has no
order.

10.

"4 SNSR ID Registration Completed." is displayed. Then,
select "OK."

NOTE:

The TPMS indicator illuminates for tire pressure

alarm.

11.

After tire pressure sensor ID registration, turn the ignition
switch to the "LOCK" (OFF) position.

12.

Remove scan tool MB991958.

WIRELESS CONTROL MODULE (WCM)

42C-93

ON-VEHICLE SERVICE

TIRE PRESSURE SENSOR CHECK

M14209200069USA0000010000

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

Check the condition of the tire pressure sensor as described
below.

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

Connect scan tool MB991958 to the data link connector.

Turn the ignition switch to the "ON" position.

Select "Interactive Diagnosis" from the start-up screen.

Select "System select."

Select "Special Function."

Select "Tire Pressure Sensor Check."

"Tire Pressure Sensor Check. Do you want to start?" is
displayed. Then, select "OK."

Change the pressure of tire to be checked for 20 kPa or more.
(The tire pressure can either be decreased or increased.)

Check the data on the PC display.

NOTE:

｠

It may take approximately one minute for the ID code to be
displayed on the M.U.T.-III screen after the tire pressure is
changed.

｠

If the ID code is not displayed, change the tire pressure
another 20 kPa or more. If the ID code is not still displayed,
rotate the tire to displace the TPMS transmitter, and change
the tire pressure 20 kPa or more again.

10.

After tire pressure sensor check, turn the ignition switch to
the "LOCK" (OFF) position.

11.

Remove scan tool MB991958.

TIRE PRESSURE SENSOR ID CHECK

M14209200070USA0000010000

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A

Check the tire pressure sensor IDs, which is registered in the
TPMS receiver, as described below.

42C-94

WIRELESS CONTROL MODULE (WCM)

ON-VEHICLE SERVICE

Content .. 831 832 833 834 ..