|
|
|
The following abbreviations are used to represent values for Control Module Pin-Out data
I
Input
S
SCP Network
B+
Battery Voltage
Hz
Frequency
O
Output
A
ACP Network
V
Voltage (DC)
kHz
Frequency x 1000
REF
Reference Voltage / Ground
D
Serial and Encoded Data
PWM
Pulse Width Modulated
mA
Milliamperes
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation.
THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE:
July 1999
Fig. 05.2
COMPONENTS
Component
Connector(s)
Connector Description
Location
ABS/TC CONTROL MODULE
FH33
25-WAY / BLACK
ADJACENT TO ABS PUMP
BRAKE SWITCH
CA37
2-WAY / GREEN
TOP OF BRAKE PEDAL
INSTRUMENT PACK
FC14
22-WAY / GREY
FASCIA
FC15
20-WAY / BLACK
FASCIA
FC63
22-WAY / BLACK
FASCIA
STEERING ANGLE RATE SENSOR
FC16
4-WAY / GREY
STEERING COLUMN
TRACTION CONTROL SWITCH
CA45
8-WAY / BLUE
CENTER CONSOLE
WHEEL SPEED SENSOR – LH FRONT
FH19
2-WAY / BLACK
WHEEL HUB, LH FRONT
WHEEL SPEED SENSOR – LH REAR
CV3
2-WAY / BLACK
WHEEL HUB, LH REAR
WHEEL SPEED SENSOR – RH FRONT
FH44
2-WAY / BLACK
WHEEL HUB, RH FRONT
WHEEL SPEED SENSOR – RH REAR
CV6
2-WAY / BLACK
WHEEL HUB, RH REAR
HARNESS IN-LINE CONNECTORS AND JUNCTION CONNECTORS
Connector
Connector Description
Location
CV1
6-WAY / GREY / CABIN HARNESS TO CANISTER CLOSE VALVE HARNESS
ABOVE REAR AXLE ASSEMBLY
FC3
16-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS
BEHIND LOWER ‘A’ POST TRIM, LH SIDE (LHD) OR RH SIDE (RHD)
FC5
12-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS
BEHIND FASCIA END PANEL, LH SIDE
FH13
20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS
ADJACENT TO PRIMARY JUNCTION BOX
GROUNDS
Ground
Ground Description
Location
FH42
GROUND EYELET
ADJACENT TO ABS/TC OR DSC CONTROL MODULE / ENGINE COMPARTMENT
CONTROL MODULE PIN-OUT INFORMATION (FOLD OUT PAGE)
CONTROL MODULE PIN-OUT INFORMATION
ABS / Traction Control Control Module
P
Pin
Description
Active
Inactive
I
FH33-2
BRAKE ON / OFF SWITCH
BRAKE ON: B+
BRAKE OFF: GROUND
I
FH33-3
RH FRONT WHEEL SPEED SENSOR
82 Hz @ 10 mph: 164 Hz @ 20 mph (0.8 – 1.5 V)
REF
FH33-4
RH FRONT WHEEL SPEED SENSOR REFERENCE SUPPLY
B+
B+
REF
FH33-6
RH REAR WHEEL SPEED SENSOR REFERENCE SUPPLY
B+
B+
I
FH33-7
RH REAR WHEEL SPEED SENSOR
82 Hz @ 10 mph: 164 Hz @ 20 mph (0.8 – 1.5 V)
I
FH33-8
GROUND SUPPLY
GROUND
GROUND
I
FH33-9
PRESSURE PUMP BATTERY POWER SUPPLY
B+
GROUND
S
FH33-10
SCP -
2 – 1600 Hz
S
FH33-11
SCP+
2 – 1600 Hz
I
FH33-14
TRACTION CONTROL ON / OFF SWITCH
B+ (MOMENTARY)
GROUND
I
FH33-17
LH FRONT WHEEL SPEED SENSOR
82 Hz @ 10 mph: 164 Hz @ 20 mph (0.8 – 1.5 V)
REF
FH33-18
LH FRONT WHEEL SPEED SENSOR REFERENCE SUPPLY
B+
B+
I
FH33-20
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
I
FH33-21
LH REAR WHEEL SPEED SENSOR
82 Hz @ 10 mph: 164 Hz @ 20 mph (0.8 – 1.5 V)
REF
FH33-22
LH REAR WHEEL SPEED SENSOR REFERENCE SUPPLY
B+
B+
D
FH33-23
SERIAL DATA LINK
ENCODED COMMUNICATIONS
I
FH33-24
GROUND SUPPLY
GROUND
GROUND
I
FH33-25
BATTERY POWER SUPPLY
B+
GROUND
Instrument Pack
P
Pin
Description
Active
Inactive
S
FC15-15
SCP +
2 – 1600 Hz
S
FC15-16
SCP -
2 – 1600 Hz
NOTE: Refer to the Appendix at the rear of this book for SCP Network Messages.
The following abbreviations are used to represent values for Control Module Pin-Out data
I
Input
S
SCP Network
B+
Battery Voltage
Hz
Frequency
O
Output
A
ACP Network
V
Voltage (DC)
kHz
Frequency x 1000
REF
Reference Voltage / Ground
D
Serial and Encoded Data
PWM
Pulse Width Modulated
mA
Milliamperes
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation.
THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE:
July 1999
Fig. 05.3
COMPONENTS
Component
Connector(s)
Connector Description
Location
ABS/TC CONTROL MODULE
FH33
25-WAY / BLACK
ADJACENT TO ABS PUMP
ACCELEROMETER – FRONT LATERAL
FH70
3-WAY / GREY
ADJACENT TO LH FRONT SUSPENSION TURRET
ACCELEROMETER – FRONT VERTICAL
FH63
3-WAY / GREY
ADJACENT TO LH FRONT SUSPENSION TURRET
ACCELEROMETER – REAR VERTICAL
CA17
3-WAY / GREY
TRUNK, BEHIND CARPET
ADAPTIVE DAMPING CONTROL MODULE
CA11
16-WAY / BLUE
IN THE SPARE WHEEL WELL
CA12
16-WAY / GREY
IN THE SPARE WHEEL WELL
DAMPER SOLENOID – LH FRONT
AS2L
1-WAY / BLACK
ENGINE COMPARTMENT, LH FRONT DAMPER
DAMPER SOLENOID – LH REAR
CA140
1-WAY / BLACK
LH REAR DAMPER
DAMPER SOLENOID – RH FRONT
AS2R
1-WAY / BLACK
ENGINE COMPARTMENT, RH FRONT DAMPER
DAMPER SOLENOID – RH REAR
CA111
1-WAY / BLACK
RH REAR DAMPER
DYNAMIC STABILITY CONTROL CONTROL MODULE
FH51
47-WAY / GREY
ADJACENT TO ABS PUMP
INSTRUMENT PACK
FC14
22-WAY / GREY
FASCIA
FC15
20-WAY / BLACK
FASCIA
FC63
22-WAY / BLACK
FASCIA
POWERTRAIN CONTROL MODULE
FH1
58-WAY / GREY
FRONT BULKHEAD, PASSENGER SIDE
GB1
32-WAY / GREY
FRONT BULKHEAD, PASSENGER SIDE
PI1
60-WAY / GREY
FRONT BULKHEAD, PASSENGER SIDE
HARNESS IN-LINE CONNECTORS AND JUNCTION CONNECTORS
Connector
Connector Description
Location
CA98
22-WAY / WHITE / JUNCTION CONNECTOR
TRUNK; ADJACENT TO RECM, RH SIDE
CA158
10-WAY / GREY / CABIN HARNESS TO CABIN HARNESS
TRUNK LATCH COVER; LH SIDE CARPET
FH13
20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS
ADJACENT TO PRIMARY JUNCTION BOX
FH28
20-WAY / BLACK / FRONT HARNESS
BEHIND LOWER ‘A’ POST TRIM, LH SIDE
FH91
3-WAY / BLACK / FORWARD HARNESS TO ADAPTIVE DAMPING LINK LEAD
ADJACENT TO SUSPENSION TURRET, RH SIDE
FH92
3-WAY / BLACK / FORWARD HARNESS TO ADAPTIVE DAMPING LINK LEAD
ADJACENT TO SUSPENSION TURRET, LH SIDE
GROUNDS
Ground
Ground Description
Location
CA156
GROUND EYELET
TRUNK; RH REAR SIDE; ADJACENT TO RECM / TRUNK RH TRIM
CONTROL MODULE PIN-OUT INFORMATION (FOLD OUT PAGE)
CONTROL MODULE PIN-OUT INFORMATION
ABS / Traction Control Control Module
P
Pin
Description
Active
Inactive
S
FH33-10
SCP -
2 – 1600 Hz
S
FH33-11
SCP+
2 – 1600 Hz
Adaptive Damping Control Module
P
Pin
Description
Active
Inactive
O
CA11-1
RH REAR DAMPER SUPPLY VOLTAGE
B+
B+
O
CA11-2
RH REAR DAMPER ACTIVATE
GROUND
B+
O
CA11-3
LH REAR DAMPER SUPPLY VOLTAGE
B+
B+
O
CA11-4
LH REAR DAMPER ACTIVATE
GROUND
B+
O
CA11-5
LH FRONT DAMPER ACTIVATE
GROUND
B+
O
CA11-6
LH FRONT DAMPER SUPPLY VOLTAGE
B+
B+
O
CA11-7
RH FRONT DAMPER ACTIVATE
GROUND
B+
O
CA11-8
RH FRONT DAMPER SUPPLY VOLTAGE
B+
B+
REF
CA11-9
ACCELEROMETER COMMON REFERENCE GROUND
GROUND
GROUND
I
CA11-10
GROUND SUPPLY
GROUND
GROUND
I
CA11-12
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
S
CA11-13
SCP -
2 – 1600 Hz
S
CA11-14
SCP +
2 – 1600 Hz
I
CA11-16
BATTERY POWER SUPPLY
B+
B+
D
CA12-4
SERIAL COMMUNICATIONS
ENCODED COMMUNICATIONS
REF
CA12-9
ACCELEROMETER COMMON REFERENCE VOLTAGE
5V
5V
I
CA12-10
REAR VERTICAL ACCELEROMETER FEEDBACK
<0.2V OR >4.8
2.3 – 2.7V = FIRM
I
CA12-11
LATERAL ACCELEROMETER FEEDBACK
<0.2V OR >4.8
2.3 – 2.7V = FIRM
I
CA12-12
FRONT VERTICAL ACCELEROMETER FEEDBACK
<0.2V OR >4.8
2.3 – 2.7V = FIRM
Dynamic Stability Control Control Module
P
Pin
Description
Active
Inactive
S
FH51-17
SCP +
2 – 1600 Hz
S
FH51-19
SCP -
2 – 1600 Hz
Instrument Pack
P
Pin
Description
Active
Inactive
S
FC15-15
SCP +
2 – 1600 Hz
S
FC15-16
SCP -
2 – 1600 Hz
Powertrain Control Module
P
Pin
Description
Active
Inactive
S
FH1-3
SCP +
2 – 1600 Hz
S
FH1-4
SCP -
2 – 1600 Hz
NOTE: Refer to the Appendix at the rear of this book for SCP Network Messages.
The following abbreviations are used to represent values for Control Module Pin-Out data
I
Input
S
SCP Network
B+
Battery Voltage
Hz
Frequency
O
Output
A
ACP Network
V
Voltage (DC)
kHz
Frequency x 1000
REF
Reference Voltage / Ground
D
Serial and Encoded Data
PWM
Pulse Width Modulated
mA
Milliamperes
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation.
THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE:
July 1999
Fig. 06.1
COMPONENTS
Component
Connector(s)
Connector Description
Location
AIR CONDITIONING CONTROL MODULE
FC27
26-WAY / GREY
BEHIND AIR CONDITIONING CONTROL PANEL
FC28
22-WAY / GREY
BEHIND AIR CONDITIONING CONTROL PANEL
AMBIENT TEMPERATURE SENSOR
FH30
2-WAY / BLACK
FORWARD OF RADIATOR; RH SIDE
AUXILIARY COOLANT PUMP
FH74
1-WAY / BLACK
REARWARD OF RADIATOR
BLOWER MOTOR
AC1
5-WAY / BLACK
BLOWER HOUSING
BLOWER MOTOR
AC2
2-WAY / BLACK
BLOWER HOUSING
COOL AIR BYPASS SERVO MOTOR
AC4
6-WAY / BLACK
AIR DISTRIBUTION BOX
DEFROST MODE ACTUATOR
FC29
6-WAY / BLACK
AIR DISTRIBUTION BOX, LH SIDE
DISCHARGE TEMPERATURE SENSOR – LH
FC20
2-WAY / GREY
AIR DISTRIBUTION BOX, LH SIDE
DISCHARGE TEMPERATURE SENSOR – RH
FC30
2-WAY / GREY
AIR DISTRIBUTION BOX, RH SIDE
DUAL COOLANT CONTROL VALVE
CF4
3-WAY / BLACK
REARWARD OF RADIATOR
DUAL SOLAR SENSOR
SL1
4-WAY / BLACK
TOP OF FASCIA
EVAPORATOR DISCHARGE TEMPERATURE SENSOR
AC5
2-WAY / GREY
EVAPORATOR / HEATER CORE DUCT
FLOOR MODE ACTUATOR
FC21
6-WAY / BLACK
AIR DISTRIBUTION BOX, LH SIDE
FRONT POWER DISTRIBUTION BOX
ENGINE COMPARTMENT, RH FRONT
IN-CAR TEMPERATURE SENSOR
FC24
2-WAY / GREEN
FASCIA DUCT, DRIVER SIDE
PANEL MODE ACTUATOR
FC22
6-WAY / BLACK
AIR DISTRIBUTION BOX, RH SIDE
REAR ELECTRONIC CONTROL MODULE
CA63
17-WAY / BLACK
TRUNK, RH REAR
CA99
4-WAY / GREY
TRUNK, RH REAR
CA100
12-WAY / BLACK
TRUNK, RH REAR
CA101
20-WAY / BLACK
TRUNK, RH REAR
CA102
22-WAY / BLACK
TRUNK, RH REAR
CA103
26-WAY / WHITE
TRUNK, RH REAR
CA104
4-WAY / BLACK
TRUNK, RH REAR
RECIRCULATION MODE SERVO MOTOR
AC3
6-WAY / BLACK
INTAKE AIR DUCT
WINDSHIELD HEATER – LH
CA121
1-WAY / BLACK
WINDSHIELD
CA122
1-WAY / BLACK
WINDSHIELD
WIPER PARK HEATER OR RH WINDSHIELD HEATER
CA65
1-WAY / BLACK
WINDSHIELD
CA71
1-WAY / BLACK
WINDSHIELD
HARNESS IN-LINE CONNECTORS AND JUNCTION CONNECTORS
Connector
Connector Description
Location
AC7
2-WAY / GREY / CABIN HARNESS TO AIR CONDITIONING HARNESS
ABOVE BLOWER ASSEMBLY
CF1
6-WAY / GREY / FRONT HARNESS TO COOLING FANS LINK LEAD
REARWARD OF RADIATOR
FC3
16-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS
BEHIND LOWER ‘A’ POST TRIM, LH SIDE (LHD) OR RH SIDE (RHD)
FC5
12-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS
BEHIND FASCIA END PANEL, LH SIDE
FC12
22-WAY / WHITE / JUNCTION CONNECTOR
ADJACENT TO STEERING COLUMN MOTOR
FC13
22-WAY / WHITE / JUNCTION CONNECTOR
ADJACENT TO STEERING COLUMN MOTOR
FC34
16-WAY / GREEN / FASCIA HARNESS TO A/C HARNESS
LH SIDE (LHD) OR RH SIDE (RHD) OF AIR DISTRIBUTION BOX
SL3
10-WAY / GREY / FASCIA HARNESS TO ROAD PRICING MODULE LINK LEAD
BEHIND FASCIA END PANEL, RH SIDE
GROUNDS
Ground
Ground Description
Location
CA30
GROUND EYELET
LOWER ‘A’ POST; LH SIDE / ‘A’ POST TRIM
CA50
GROUND EYELET
LOWER ‘A’ POST; RH SIDE / ‘A’ POST TRIM
FC38
GROUND EYELET
BEHIND CENTER CONTROL CONSOLE / CENTER CONSOLE TRIM
FH42
GROUND EYELET
ADJACENT TO ABS/TC OR DSC CONTROL MODULE / ENGINE COMPARTMENT
CONTROL MODULE PIN-OUT INFORMATION (FOLD OUT PAGE)
CONTROL MODULE PIN-OUT INFORMATION
Air Conditioning Control Module
P
Pin
Description
Active
Inactive
I
FC27-1
DEFROST MODE ACTUATOR POSITION FEEDBACK
2.9V = OPEN
2.5V = CLOSED
I
FC27-2
COLD AIR BY-PASS ACTUATOR POSITION FEEDBACK
0.68V = HIGH TEMPERATURE; 3.89V = LOW TEMPERATURE
I
FC27-3
PANEL MODE ACTUATOR POSITION FEEDBACK
2.2V = OPEN
1.1V = CLOSED
O
FC27-5
PASSENGER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE
GROUND = HIGH TEMPERATURE; PWM (GROUND) = VARIABLE TEMPERATURE; B+ = LOW TEMPERATURE
O
FC27-6
DRIVER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE
GROUND = HIGH TEMPERATURE; PWM (GROUND) = VARIABLE TEMPERATURE; B+ = LOW TEMPERATURE
O
FC27-8
BLOWER MOTOR CONTROLLER HIGH SPEED RELAY DRIVE
B+ = HIGH SPEED; < 0.2V = LOW SPEED
O
FC27-9
RECIRCULATION ACTUATOR DRIVE – CLOSE
B+
GROUND
O
FC27-10
RECIRCULATION ACTUATOR DRIVE – OPEN
B+
GROUND
O
FC27-11
COLD AIR BY-PASS ACTUATOR DRIVE – CLOSE
B+
GROUND
O
FC27-12
COLD AIR BY-PASS ACTUATOR DRIVE – OPEN
B+
GROUND
O
FC27-13
DEFROST MODE ACTUATOR DRIVE – OPEN
B+
GROUND
REF
FC27-14
IN CAR TEMPERATURE SENSOR REFERENCE VOLTAGE
5V (NOMINAL)
5V (NOMINAL)
I
FC27-15
RECIRCULATION ACTUATOR POSITION FEEDBACK
0.3V = OPEN
3.6V = CLOSED
I
FC27-16
FLOOR MODE ACTUATOR POSITION FEEDBACK
3.4V = OPEN
1.2V = CLOSED
REF
FC27-17
ACTUATORS COMMON REFERENCE GROUND
GROUND
GROUND
O
FC27-18
AUXILIARY COOLANT PUMP RELAY ACTIVATE
GROUND
B+
O
FC27-19
BLOWER MOTOR RELAY ACTIVATE
GROUND
B+
O
FC27-20
HEATED WIPER PARK OR HEATED WINDSHIELD RELAY(S) ACTIVATE
GROUND
B+
O
FC27-22
FLOOR MODE ACTUATOR DRIVE – OPEN
B+
GROUND
O
FC27-23
FLOOR MODE ACTUATOR DRIVE – CLOSE
B+
GROUND
O
FC27-24
PANEL MODE ACTUATOR DRIVE – OPEN
B+
GROUND
O
FC27-25
PANEL MODE ACTUATOR DRIVE – CLOSE
B+
GROUND
O
FC27-26
DEFROST MODE ACTUATOR DRIVE – CLOSE
B+
GROUND
S
FC28-1
SCP -
2 – 1600 Hz
I
FC28-2
GROUND SUPPLY
GROUND
GROUND
I
FC28-3
IGNITION SWITCHED POWER SUPPLY
B+
GROUND
O
FC28-4
ENGINE COOLING FAN REQUEST
GROUND = ON
B+ = OFF
I
FC28-5
BLOWER MOTOR CONTROLLER FEEDBACK
0.3V = HIGH
9V = LOW
I
FC28-6
PASSENGER DISCHARGE AIR TEMPERATURE SENSOR FEEDBACK
3.25V @ 0
°
C (32
°
F) DECREASING VOLTAGE WITH TEMPERATURE INCREASE
I
FC28-7
DUAL SOLAR SENSOR FEEDBACK – LH
4.5V = COVERED
4.4V = AMBIENT LIGHT
REF
FC28-8
AMBIENT TEMPERATURE SENSOR GROUND
GROUND
GROUND
I
FC28-9
IN CAR TEMPERATURE SENSOR FEEDBACK
3.25V @ 0
°
C (32
°
F) DECREASING VOLTAGE WITH TEMPERATURE INCREASE
I
FC28-10
EVAPORATOR TEMPERATURE SENSOR FEEDBACK
3.25V @ 0
°
C (32
°
F) DECREASING VOLTAGE WITH TEMPERATURE INCREASE
REF
FC28-11
ACTUATORS COMMON REFERENCE GROUND
GROUND
GROUND
S
FC28-12
SCP +
2 – 1600 Hz
I
FC28-14
BATTERY POWER SUPPLY
B+
B+
O
FC28-15
BLOWER MOTOR CONTROLLER DRIVE
0.7V = HIGH
1.2V = LOW
REF
FC28-16
EVAPORATOR DISCHARGE TEMPERATURE SENSOR REFERENCE GROUND
GROUND
GROUND
I
FC28-17
AMBIENT TEMPERATURE SENSOR FEEDBACK
3.25V @ 0
°
C (32
°
F) DECREASING VOLTAGE WITH TEMPERATURE INCREASE
I
FC28-18
DRIVER DISCHARGE AIR TEMPERATURE SENSOR FEEDBACK
3.25V @ 0
°
C (32
°
F) DECREASING VOLTAGE WITH TEMPERATURE INCREASE
REF
FC28-19
SENSOR COMMON REFERENCE VOLTAGE
5V (NOMINAL)
5V (NOMINAL)
I
FC28-20
DUAL SOLAR SENSOR FEEDBACK – RH
4.5V = COVERED
4.4V = AMBIENT LIGHT
REF
FC28-22
ACTUATORS COMMON VOLTAGE REFERENCE
5V (NOMINAL)
5V (NOMINAL)
NOTE: Refer to the Appendix at the rear of this book for SCP Network Messages.
|