Infiniti EX35. Manual - part 164

AV

INSPECTION AND ADJUSTMENT

AV-437

< BASIC INSPECTION >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000003160593

WITH REAR VIEW MONITOR OR AROUND VIEW MONITOR

Always correct the center position of the predicted course line after disconnecting the battery negative termi-
nal.

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000003160594

1.

CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE

Refer to the following for details.

>> Refer to 

AV-437, "PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special

Repair Requirement"

.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000003160595

When camera control unit or around view monitor control unit is replaced, the center position of predicted
course line shall be corrected.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000003160596

1.

CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE

Refer to the following for details.

>> Refer to 

AV-437, "PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special

Repair Requirement"

.

PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT

PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Description

INFOID:0000000003160597

Adjust the center position of the predicted course line of the rear view monitor if it is shifted.

PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special Repair 
Requirement

INFOID:0000000003160598

1.

STEERING OPERATION

Steer the steering wheel to the leftmost and rightmost ends.

>> GO TO 2

2.

DRIVING

Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.

>> END

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)

AV-438

< BASIC INSPECTION >

[BOSE AUDIO WITH NAVIGATION]

INSPECTION AND ADJUSTMENT

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description

INFOID:0000000003166669

• Perform the calibration and perform the writing to the around view monitor control unit when removing and

replacing each camera, removing the camera mounting parts (front grille, door mirror, etc.) and replacing the
around view monitor control unit. 

• Align the white lines on the road near the vehicle at the boundary of each camera image by this camera cal-

ibration. The white lines far from the vehicle may not be aligned at the boundary of each camera image. The
farther the line, the greater the difference is. 

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Special Repair Re-
quirement

INFOID:0000000003166670

Calibration flowchart

Following the flowchart shown in the figure, perform the calibration. 

NOTE:
In the un-match display, the un-match camera position is indicated
as “X” on the birds-eye view. 

Calibration procedure

1.

AROUND VIEW MONITOR SCREEN CONFIRMATION

JSNIA1056GB

JSNIA1052GB

AV

INSPECTION AND ADJUSTMENT

AV-439

< BASIC INSPECTION >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Check that there is the un-match display in any camera. 

Is the un-match display visible?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK THAT AROUND VIEW MONITOR CONTROL UNIT IS REPLACED

Check that the around view monitor control unit is replaced.

Is the around view monitor control unit replaced?

YES

>> GO TO 3.

NO

>> GO TO 5.

3.

RELEASE UN-MATCH DISPLAY (PERFORM ONLY WHEN THE AROUND VIEW MONITOR CONTROL

UNIT IS REPLACED)

1.

Select “Camera Cont.” of Confirmation/ Adjustment mode, and then set to “Calibrating Camera Image”
mode. 

2.

Press the“ENTER” switch of the multifunction switch on each
screen of “Rear Camera”, “Front Camera”, “Dr-Side Camera”,
“Pass-Side Camera”. 

CAUTION:

• Do never operate the center dial and up/down/left/right

switches. Only press the “ENTER” switch. 

• Never perform “Initialize Camera Image Calibration”. 

3.

Display the around view monitor screen, and check that there is
no malfunction such as a difference between each camera
image. 

Is there a malfunction?

YES

>> Calibration end

NO

>> GO TO 1.

4.

PERFORM SIMPLIFIED CONFIRMATION/ADJUSTMENT BY “FINE TUNING OF BIRDS-EYE VIEW”

1.

Put target line 1 on the ground beside each axle using packing tape, etc. 

2.

Put target lines 2 equal to the vehicle total length + approximately 1.0 m (39.3 in) from the vehicle side
(right and left) at approximately 30 cm (11.8 in) away from the vehicle (make the line as parallel with the
vehicle as possible) 

Preparation of simplified target line

JSNIA1052GB

JSNIA1053GB

JSNIA0927ZZ

AV-440

< BASIC INSPECTION >

[BOSE AUDIO WITH NAVIGATION]

INSPECTION AND ADJUSTMENT

3.

Select “Camera Cont.” of Confirmation/ Adjustment mode, and then set to “Fine Tuning of Birds-Eye View-
mode. 

4.

Select left and right cameras by pressing the “CAMERA” switch, and perform the following confirmation. 

-

Check that target line 1 is aligned with the marker on the screen. Overlap the line aligned to the marker
with the upper/lower switches if necessary. 

-

Check if there is a difference between target lines 2 between cameras. Adjust target lines 2 to be straight
lines by operating the center dial and left/right switches if necessary. 

CAUTION:

•

Never adjust the front camera and rear camera. Only adjust the right and left cameras. 

•

Operate the center dial slowly because the changing of the screen takes approximately 1 sec-
ond. 

Simplified target line adjustment method

5.

Adjust left and right cameras. Check that the difference between target line 1 and the marker on the
screen, and between target lines 2 is solved. 
NOTE:
• It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration” of

“Calibrating Camera Image”. 

• The adjustment value is cancelled on this mode by performing “Initialize Camera Image Calibration”. 

Is the difference corrected?

YES

>> Finish the writing to around view monitor control unit by pressing “ENTER” switch. 

NO

>> GO TO 5.

5.

PERFORM “CALIBRATING CAMERA IMAGE”

Preparation of target line
1.

Hang a string with a weight as shown in the figure. Put the points FM0, RM0 (mark) on the ground at the
center of the vehicle front end and rear end with white packing tape or a pen. 

2.

Route the vinyl string under the vehicle, and then pull and fix it on the point approximately 1.0 m (39.9 in)
to the front and rear of the vehicle through the points FM0 and RM0 using packing tape. 

1.

Target lines 1

2.

Target lines 2

A.

Approx. 30 cm (11.8in)

B.

Approx. 1.0 m (39.3 in)

JSNIA0929ZZ

1.

Target lines 1

2.

Target lines 2

3.

Marker for target line 1

4.

Boundary between cameras

5.

Crosshairs cursor (mark indicated 
the selected camera)

A.

Adjustment method for target lines 1 
(right)

B.

Adjustment method for target lines 2 
(right)