Infiniti EX35. Manual - part 28

ADP-106

< COMPONENT DIAGNOSIS >

MIRROR SENSOR

Is the indication normal?

YES

>> INSPECTION END

NO

>> Perform diagnosis procedure. Refer to 

ADP-106, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000003134748

1.

CHECK DOOR MIRROR SENSOR (PASSENGER SIDE) POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (passenger side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR POWER SUPPLY CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic driver positioner control unit. Refer to 

ADP-210, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

3.

CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR GROUND 

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) connector.

Monitor item

Condition

Value

MIR/SEN RH U-D

Door mirror (passenger side)

Change between 

3.4 [V] (close to peak)

0.6 [V] (close to valley)

MIR/SEN RH R-L

Change between 

3.4 [V] (close to left edge)

0.6 [V] (close to right edge)

(+)

(–)

Voltage (V)

(Approx.)

Door mirror (passenger side)

Connector

Terminal

D33

23

Ground

5

Automatic drive positioner control unit

Door mirror (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M52

33

D33

23

Existed

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M52

33

Not existed

MIRROR SENSOR

ADP-107

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connector.

4.

CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR HARNESS CONTINUITY

1.

Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.

2.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace door mirror sensor. (Built in passenger side door mirror).

NO

>> Repair or replace harness or connector.

Automatic drive positioner control unit

Door mirror (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M52

41

D33

24

Existed

Automatic drive positioner control unit

Door mirror (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M51

5

D33

21

Existed

21

22

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M51

5

Not existed

21

ADP-108

< COMPONENT DIAGNOSIS >

SLIDING MOTOR

SLIDING MOTOR

Description

INFOID:0000000003134749

• The seat sliding motor is installed to the seat cushion frame.
• The seat sliding motor is installed with the driver seat control unit.
• The seat is slid frontward/rearward by changing the rotation direction of sliding motor.

Component Function Check

INFOID:0000000003134750

1.

CHECK FUNCTION

1.

Turn ignition switch ON.

2.

Select “SEAT SLIDE” in “Active test” mode with CONSULT-III.

3.

Check the sliding motor operation.

Is the operation of relevant parts normal?

YES

>> INSPECTION END

NO

>> Perform diagnosis procedure. Refer to 

ADP-108, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000003134751

1.

CHECK SLIDING MOTOR POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect sliding motor connector.

3.

Turn the ignition switch ON.

4.

Perform “Active test” (“SEAT SLIDE”) with CONSULT-lll

5.

Check voltage between sliding motor harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding motor. (Built in seat slide cushion frame.)

NO

>> GO TO 2.

2.

CHECK SLIDING MOTOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect driver seat control unit connector.

3.

Check continuity between driver seat control unit harness connector and sliding motor harness connector.

Test item

Description

SEAT SLIDE

OFF

Seat sliding

Stop

FR

Forward

RR

Backward

(+)

(-)

Condition

Voltage (V)

(Approx.)

Sliding motor

Connector

Terminal

B461

35

Ground

SEAT SLIDE

OFF

0

FR (forward)

Battery voltage

RR (backward)

0

42

OFF

0

FR (forward)

0

RR (backward)

Battery voltage

SLIDING MOTOR

ADP-109

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

4.

Check continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace driver control unit. Refer to 

ADP-209, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

Driver seat control unit

Sliding motor

Continuity

Connector

Terminal

Connector

Terminal

B452

35

B461

35

Existed

42

42

Driver seat control unit 

Ground

Continuity 

Connector

Terminal

B452

35

Not existed

42