197

III. WIPER SWITCH ASSEMBLY REPLACEMENT

1. DETACH STEERING WHEEL ASSEMBLY

(a) Disconnect the main power source of the vehicle.

(b) Remove the passenger SRS module assembly, and cautiously put it in a safe place.

(c) Loosen steering wheel lock-bolts and remove the assembly.

2. REMOVE WIPER SWITCH

(a) Disconnect the connector.

(b) Remove the 2 tapping screws that are for mounting the wiper switch, take out the wiper switch from the

bracket of the combination switch.

IV. WASHER NOZZLE

ADJUSTMENT

1. INSPECT WASHER NOZZLE

(a) Start the engine, check if the position where the washer fluid from the nozzle sprays the windshield is in

the central or upper of the area wiped by the blades.

(b) Change the direction (horizontal) of the nozzle hole to adjust the point where washer fluid sprays the

windshield.

198

Chapter 5 Light System

Section 1 Survey of Light System

I. COMPOSITION

1. Front combination lamp assembly: turn signal lamp, high beam, low beam, head lamp, front position lamp.

2. Rear combination lamp: turn signal lamp, back-up lamp, rear fog lamp, tail lamp, brake lamp, retro reflector.

3. Front fog lamp

4. Side turn signal lamp

5. High mounted stop lamp

6. Rear trunk lamp

7. License plate lamp

8. Interior dome lamp

9. Rear row reading lamp

10. Door lampshield and bulb assembly

II. NOTES FOR REPAIR

1. NOTES WHEN REPAIRING ELECTRICAL EQUIPMENTS

(a) Disconnect the battery ground cable.

2. Notes when replacing a headlamp bulb

(a) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.

(b) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.

(c) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are

turned ON, its service life will be shortened.

(d) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.

They can explode if dropped to ground.The glass fragments will splash up.

(e) When replacing, make sure to use the bulbs with the same power, same model.

(f) After the bulb is installed, make the lamp holder tight.

199

III.  BULB SPECIFICATIONS

Notes: All bulbs are made by Philips Corp..

Name

Specifications

Headlamp (High beam and Low beam)

H1 12V 55W

Turn signal lamp

P21W 12V 21W

Position lamp

W5W 12V 5W

Front fog lamp

H3 12V 55W

Rear combination lamp (Turn signal lamp)

PY21W 12V 21W

Rear combination lamp (Brake / Position lamp)                          P21/5W 12V 21/5W

Rear combination lamp (Rear fog lamp)

P21W 12V 21W

Rear combination lamp (Back-up lamp)

P21W 12V 21W

C5W 12V 5W

W5W 12V 5W

Rear row reading lamp

C5W 12V 5W

Side turn signal lamp

WY5W 12V 5W

High mounted stop lamp (incl. rear trunk lamp)

W5W 12V 5W

License plate lamp

W5W 12V 5W

Door courtesy lamp

W5W 12V 5W

Interior lamp (dome lamp)

200

IV. LOCATION OF LIGHT SYSTEM

Fuse Box

Interior Lamp

Rear Row

Reading Lamp

LH Turn Lamp Assembly

Lamp Assembly

LH Front Fog Assembly

Front Headlamp Height
Adjusting Switch

Headlamp Switch Lamp 
Control Switch, Haedlamp 
DIM Switch Turn Signal 
Lamp Switch

Hazard Warning

Switch

Parking Brake Switch

Backup Lamp Switch

Brake Switch

Door Courtesy Lamp Switch

LH/Front, Rear Door 

Courtesy Lamp Assembly

LH Front Combined