3. Circuit 

figure 

NL02-2159b

5 IP24

8 IP24

7 IP24

46 EN01

75 EN01

IP12

7

芯片防盗模块

诊断接口

ECM

IMMOREQ

KW2000

R-LINE

W-LINE

K-LINE

Gr

/P

 

4. Diagnostic 

Steps: 

Refer to 2.5.7.17 Engine Anti-theft Warning Lamp Flashing, Vehicle Can Not Start 

5. Maintenance 

guide 

: 

Refer to 2.5.7 “Diagnostic Information and Procedures” of the engine anti-theft system to repair 
the anti-theft system. 

Chip anti-theft 

module 

Diagnostics 

interface 

907

2.12.7.56 DTC P0831 P0832 

1. DTC 

description: 

DTC  P0831 

Clutch switch circuit at low voltage 

 

DTC  P0832 

Clutch switch circuit at high voltage 

When clutch switch is short to the ground or open (at high voltage), after several times of 
acceleration from starting-up to >52 Km/h, or deceleration from >52 Km/h to <3 Km/h, the DTC 
codes appear with the engine running stably, and the vehicle can be driven. 

2.  Conditions For Setting DTC and The Fault Location: 

DTC 
Code 

DTC Detection 
Strategy 

Conditions For Setting The DTC 
(Control Strategy) 

Fault Locations 

P0831 

1.  Clutch switch signal disconnect or 

high voltage 

2.  Acceleration from starting-up to 

>52 Km/h, or deceleration from >52 
Km/h to <3 Km/h. 

3.  DTC codes appear after repeatedly 

braking. 

P0832 

ECM receives the 
clutch signal 

1.  Clutch switch signal short. 

2.  Acceleration from starting-up to 

>52 Km/h, or deceleration from >52 
Km/h to <3 Km/h. 

3.  DTC codes appear after repeatedly 

braking. 

1. Clutch 

Switch 
Circuit 

2. Clutch 

Switch 

3. ECM 

908

3. Circuit 

figure 

NL02-2306b

10

A

IF0

3

ECM

35

EN01 CS

2

IP60

1

IP60

R

离合器开关

 

4. Diagnostic 

Steps: 

Notes: 

Before carrying out this diagnosis steps, observe the data list on fault diagnosis tester and 
analyze the accuracy of the data, as these will help with quick diagnosis. 

1 

Inspect for other DTC Codes other than P0831 and P0832. 

A.  Connect fault diagnosis tester to the vehicle diagnostic interface. 

B.  Rotated ignition switch to ON position. 

C.  Press the power button of fault diagnosis tester. 

D.  Select the following menu items: Engine/Read DTC codes. 

E.  Read DTC codes. 

Results 

DTC Codes shown 

To Step 

DTC P0831 P0832 

Yes 

DTC Code Other Than DTC P0831 P0832 

No 

 

Yes 

Refer to 2. 12.6.11 DTC Chapter Index. 

No 

Clutch switch

909

2 

Is the clutch switch working correctly? 

Note: When the clutch switch fails, during emergent acceleration and deceleration, the vehicle 
will vibrate seriously and even push forward. 

 

3 

Inspect the continuity between clutch switch wiring harness connector IP60 and ECM 
harness connector EN01. 

 

A.  rotated ignition switch to OFF 

position. 

B. 

Disconnect ECM harness 
connector EN01. 

C.  Press the brake pedal. 

D.  Measure ECM harness connector 

EN01 terminal No.34 resistance. 

Standard Resistance: Less than 3 Ω 

Confirm whether the resistance is 
normal. 

NL02-2307b

IP60 离合器开关线束连接器

1

2

 

4 

Repair the circuit between clutch switch wiring harness connector IP60 and ECM 
harness connector EN01. 

A.  Repair the circuit between clutch switch wiring harness connector IP60 and ECM harness 

connector EN01. 

B.  Confirm the repair is completed. 

 

5 

Is the clutch switch working correctly? 

Note: When the clutch switch fails, during emergent acceleration and deceleration, the vehicle 
will vibrate seriously and even push forward. 

Next 

Yes 

Refer to 2.12.8.1 Replacement of Engine 
Control Module to replace ECM. 

No 

Yes 

Refer to 2.12.7.3 Intermittent Fault 
Inspection for intermittent fault. 

No 

IP60 Clutch switchharness connector 

910