Freightliner FLA/FLB/FLC/FLD/FLL. Manual - part 3

The M1 Maintenance Interval Operations table lists
all maintenance operations that are to be performed
at the M1 maintenance interval. Maintenance opera-
tion numbers are reference numbers used to help
you find detailed instructions in this manual on the
maintenance operations to be performed.

IMPORTANT: After performing all operations listed in
this table, perform all daily, weekly, and monthly
maintenance operations listed in the "Pretrip and
Post-Trip Inspections and Maintenance" chapter of
the vehicle driver’s manual.

M1 Maintenance Interval Operations for Service Schedules I, II, and III

Maintenance

Operation Number

Operation Description

Check

00–04

Lubrication and Fluid Level Check (includes the following)

•

Clutch Release Bearing Lubricating

•

Clutch Release Cross-Shaft Lubricating

•

Clutch Linkage Components Lubricating

•

Shift Control Telescoping Tubes Lubricating and Inspecting, FLA/FLB

•

Shift Control Latch Lubricating and Cylinder Inspecting, FLA/FLB

•

Selection Lever and Pivot Rod Ball Stud Lubricating, FLA/FLB

•

Transmission Oil Level Checking and Breather Checking

•

Fifth Wheel Lubricating

•

Trailer Electrical Connector Lubricating

•

Suspension Lubricating, Front and Rear

•

Knuckle Pin Lubricating

•

Tie-Rod End Inspecting and Lubricating

•

Axle Breather and Lubricant Level Checking

•

Driveline Lubricating

•

Manual/Automatic Slack Adjuster Lubricating and Checking (All Models)

•

Steering Driveline Lubricating

•

Ross Manual Steering Gear Lubricant Checking, Model 503

•

Drag Link and Power Steering Cylinder Lubricating

•

Power Steering Reservoir Fluid Level Checking

•

Ross Power Steering Gear Lubricating, TAS Series

•

Sheppard Power Steering Gear Bearing Cap Lubricating

•

Cab-Tilt System Checking, FLA/FLB

•

Door Seal, Door Latch, and Door Hinge Lubricating

13–01

Bendix Air Compressor Inspecting

31–01

Fifth Wheel Inspecting

32–01

Suspension Inspecting

41–01

Driveline Inspecting

42–01

Brake Adjusting—Cam Brakes With Manual Slack Adjusters

General Information

M1 Maintenance Interval Operations Table: 00-07

00/13

M1 Maintenance Interval Operations for Service Schedules I, II, and III

Maintenance

Operation Number

Operation Description

Check

42–05

Wedge Brake Checking

42–11

Bendix Air Dryer or Anchorlok Aftercooler Inspecting (Bendix AD–2, AD–4, AD–9, or
Anchorlok)

42–14

CR Brakemaster Air Dryer Cleaning (Model 62 or 68)

42–22

Midland Quick Release and Flipper Valve Checking

42–24

Brake Inspection

47–02

Fuel Tank Band Nut Tightening, FLA, FLB, and FLD

60–03

Cab Latch Checking, FLA/FLB

49–01

Exhaust System Inspecting

General Information

M1 Maintenance Interval Operations Table: 00-07

00/14

The M2 Maintenance Interval Operations table lists
all maintenance operations that are to be performed
at the M2 maintenance interval. Maintenance opera-
tion numbers are reference numbers used to help
you find detailed instructions in this manual on the
maintenance operations to be performed. Perform all
M1 maintenance interval operations at the M2 main-
tenance interval.

NOTE: Maintenance operations appearing in italics in
this table are for noise emission control components.
Numbers in this table are reference numbers match-
ing those in the text of this manual.

M2 Maintenance Interval Operations for Service Schedules I, II, and III

Maintenance

Operation Number

Operation Description

Check

00–07

Perform all M1 Operations

01–03

Jacobs Engine Brake Wiring Inspecting

20–01

Radiator Cap Checking

20–03

Fan Drive and Clutch Checking

26–06

Manual Transmission Magnetic Plug Cleaning, Oil Changing, and Oil Filter Element
Changing

26–07

Transmission Air Filter/Regulator Checking, and Cleaning or Replacing

31–04

Holland Fifth Wheel Sliding Mechanism Inspecting

40–01

Wheel Nut and Rim Nut Checking

42–02

Camshaft Bracket Bushing Lubricating

42–04

Meritor Automatic Slack Adjuster Inspecting

42–07

Alcohol Evaporator Checking

42–08

Bendix Alcohol Evaporator Cleaning

42–15

Anchorlok Aftercooler Automatic Ejector Valve Clearing

42–18

Bendix Air Brake Valve Disassembly, Cleaning, Inspecting, and Lubricating (DV–2,
PP–3, and Single Check Valve)

42–21

Sealco Moisture Ejection Valve Operation- and Leak-Testing (Model 6300)

46–06

Power Steering Reservoir Fluid and Filter Changing

46–07

Steering Driveline Deck Bearing Lubricating, FLA/FLB

47–01

Fuel Tank Vent Checking

47–03

Fuel Separator Sight Bowl Cleaning and Element Replacing

60–02

Cab-Suspension Spring Center-Bolt Torque Checking, FLC

83–01

Air Conditioner Inspecting

General Information

M2 Maintenance Interval Operations Table: 00-08

00/15

The M3 Maintenance Interval Operations table lists
all maintenance operations that are to be performed
at the M3 maintenance interval. Maintenance opera-
tion numbers are reference numbers used to help
you find detailed instructions in this manual on the
maintenance operations to be performed. Perform all
maintenance interval operations in M1 and M2 when
performing M3 maintenance interval operations.

NOTE: Maintenance operations appearing in italics in
this table are for noise emission control components.
Numbers in this table are reference numbers match-
ing those in the text of this manual.

M3 Maintenance Interval Operations for Service Schedules I, II, and III

Maintenance

Operation Number

Operation Description

Check

00–07

Perform all MI Operations

00–08

Perform all M2 Operations

01–01

Engine Rear-Support Assembly Checking

01–02