Fiat 124 Spider (2020 year). Manual in english - page 3

 

  Index      Manuals     Fiat 124 Spider (2020 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     1      2      3      4      ..

 

 

 

Fiat 124 Spider (2020 year). Manual in english - page 3

 

 

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Automatic Climate Control System
Automatic Climate Controls — Type A
1 — Temperature Control Knob
4 — Rear Window Defrost Button
2 — Blower Control Knob
5 — Air Recirculation Button
3 — Mode Selector Knob
6 — A/C Button
53

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Automatic Climate Controls — Type B
1 — Temperature Control Knob
4 — Rear Window Defrost Button
2 — Blower Control Knob
5 — Air Recirculation Button
3 — Mode Selector Knob
6 — A/C Button
54

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Controls
NOTE:
To turn off the Rear Window Defroster before
the end of
15 minutes, push the switch
1 - Temperature Control Knob
† With the air flow mode set to the
posi-
again.
tion, and the Temperature Control Knob is
This knob controls internal temperature of
set to a medium temperature, the floor
CAUTION!
the vehicle. Turn it clockwise for hotter
vents will blow warmer air, and the center
temperatures and counterclockwise for
Failure to follow these cautions can cause
and side air vents will blow cooler air.
colder temperatures.
damage to the heating elements:
† When the Blower Control Knob is on, and
2 - Blower Control Knob
† Before opening the convertible top,
the Mode Selector Knob is in the
posi-
make sure the Rear Window Defrost
The fan has seven speeds. Turn the clock-
tion, the air conditioner is automatically
button is turned off. Otherwise, the heat
wise to increase blower speed or counter-
turned on, and the Air Recirculation
generated from the defroster could
clockwise to decrease blower speed/enter
Button is automatically set to the outside
damage the convertible top and the
Auto mode.
air position for windshield defrosting.
internal material.
AUTO Position: The blower speed is automat-
4 - Rear Window Defrost Button
† Use care when washing the inside of the
ically controlled by the system based upon
rear window. Do not use abrasive window
The Rear Window Defroster clears fog and
the set temperature.
cleaners on the interior surface of the
frost from the rear window. The ignition must
window. Use a soft cloth and a mild
0 Position: To turn off the system, set the dial
be placed in the ON position to use the
washing solution, wiping parallel to the
to the 0 position.
defroster.
heating elements. Labels can be peeled
3 - Mode Selector Knob
Push the button to turn on the Rear Window
off after soaking with warm water.
Defroster.
† Do not use scrapers, sharp instruments,
Turn the Mode Selector Knob to select the
The Rear Window Defroster operates for
or abrasive window cleaners on the inte-
air flow mode.
about 15 minutes, and then turns off auto-
rior surface of the window.
AUTO Position: The air flow automatically
matically.
† Keep all objects a safe distance from the
adjusts based upon the selected tempera-
window.
ture.
The button LED will illuminate when the
defroster is operating.
55

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NOTE:
dangerous as it will cause the windows to fog
NOTE:
This defroster is not designed for melting
up. Your vision will be hampered, which
If the recirculated air position is used for
snow. If there is an accumulation of snow on
could lead to a serious accident.
long periods in cold weather or high
the rear window, remove it before using the
humidity, the windshield may fog up more
6 - A/C Button
defroster.
easily.
Push the A/C Button to turn on the air condi-
Mirror Defroster (If Equipped): To turn on the
3. Set the Blower Control Knob to the AUTO
tioner.
mirror defroster, switch the ignition on and
position.
push the Rear Window Defroster Button.
The LED on the switch will illuminate when
4. Push the A/C button to operate the air
the Blower Control Knob is in any position
5 - Air Recirculation Button
conditioning (indicator light on).
except the off position.
Press the Air Recirculation Button to select
Push the button again to turn off the air
5. Set the Temperature Control Knob to the
between outside air and recirculated air posi-
conditioner.
desired position.
tions.
NOTE:
6. To turn off the system, set the blower
Recirculated Air Position: (LED On) Outside
The air conditioner may not function when
control knob to the 0 position.
air is shut off when this position has been
the outside temperature approaches
32°F
activated. Use this position when going
(0°C).
Setting the temperature to maximum hot or
through tunnels, driving in congested traffic
cold will not provide the desired temperature
(high engine exhaust areas), or when quick
Operation Of Automatic Air Conditioning
at a faster rate.
cooling of the vehicle is desired.
Proceed as follows:
When selecting heat, the system will restrict
Outside Air Position: (LED Off) Outside air is
air flow until it has warmed to prevent cold
allowed to enter the cabin. Use this mode for
1. Set the mode selector knob to the AUTO
air from blowing out of the vents.
ventilation or windshield defrosting.
position.
For an optimal cabin temperature, set the
NOTE:
2. Set the Air Recirculation Button to the
temperature close to 77°F (25°C). Adjust to
Do not use the Recirculated Air Position in
outside air position
(indicator light
the desired temperature if necessary.
cold or rainy weather. Using the Recirculated
turned off).
Air Position in cold or rainy weather is
56

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Windshield Defrosting And Defogging
Sunlight/Temperature Sensor
NOTE:
Do not obstruct either sensor. Otherwise, the
Set the mode selector knob to the
posi-
The air conditioning system measures inside
air-conditioning system will not operate
tion and turn the blower control knob to the
and outside temperatures, and sunlight.
properly.
desired speed.
It then sets temperatures inside the cabin
POWER WINDOWS
In this position, the outside air position is
accordingly.
automatically selected, and when the blower
Power Window Controls
control knob is on, the air conditioner auto-
matically turns on. The air conditioner will
The ignition must be in the ON position for
directly dehumidify the air to the front wind-
the power windows to operate.
shield and side windows. Air flow amount
will be increased.
A power window may no longer open/close if
you continue to push the switch after
Use the temperature control knob to increase
opening/closing the power window.
the air flow temperature and defog the wind-
shield more quickly.
If the power window does not open/close,
wait a moment and then operate the switch
WARNING!
Sunlight Sensor
again.
Set the temperature control to the hot or
NOTE:
warm position when defogging
(Front
To prevent burning out the fuse and
Defrost position). Using the Front Defrost
damaging the power window system, do not
position with the temperature control set
open or close both windows at once.
to the cold position is dangerous as it will
cause the outside of the windshield to fog
The passenger window can be operated with
up. Your vision will be hampered, which
each door switch when the power window
could lead to a serious accident.
lock switch on the driver's door is in the
unlocked position.
Interior Temperature Sensor
57

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Passenger Control Switches
Auto-Opening Power Windows
4. Push the switch and fully open the
window.
The passenger window can also be operated
To fully open the window automatically push
using the master control switches on the
the switch completely down. To stop the
5. Pull up the switch to fully close the
driver's door.
window partway pull or push the switch in
window and continue holding the switch
the opposite direction and then release it.
for about two seconds after the window
The power window cannot be fully closed
fully closed.
while the door is open.
6. Repeat steps four and five for the
Power Window System Initialization Procedure
passenger power window while seated in
If the battery was disconnected during
the passenger seat.
vehicle maintenance, or for other reasons
7. Make sure that the power windows
(such as a switch continues to be operated
operate correctly using the door switches.
after the window is open/closed), the window
will not fully open automatically.
After the system has been re-initialized,
Power Window Switches
passenger window can be fully opened auto-
Resetting of the automatic function can be
performed using the master control switches
matically using the master control switches.
1 — Driver's Window Switch
If the automatic power window operation
2 — Passenger's Window Switch
or each passenger door switch.
does not operate normally while the doors or
The power window auto function reset proce-
convertible top are opened/closed, reset it
dure can be done on both door switches. The
using the above procedures.
power window auto function will only resume
Engine-Off Power Window Operation
on the power window that has been reset:
1. Close the doors and the convertible top.
The power window can be operated for about
40 seconds after the ignition has been
2. Place the ignition in the ON position.
cycled from the ON to the OFF position with
both doors closed. If any door is opened, the
3. Make sure that the power window lock
power window will stop operating.
switch located on the driver's door is not
depressed.
Power Window Switch Function
58

-------------------------------------------------------------------------------------------------------------------------------------------------------------

For engine-off operation of the power
To lower the convertible top, proceed as
window, the switch must be held up firmly
follows:
throughout window closure because the
1.
Make sure the parking brake is applied
auto-closing function will be inoperable.
and the ignition is placed in the OFF
WARNING!
position.
Never leave children unattended in a
2.
Make sure there are no objects which
vehicle, and do not let children play with
have been placed in the area where the
power windows. Do not leave the key fob in
convertible top is to be retracted.
or near the vehicle, or in a location
Power Window Lockout Switch
3.
Push forward on the release latch. There
accessible to children, and do not leave
is a red indicator showing that the latch
the ignition of a vehicle equipped with the
NOTE:
is open.
Keyless Entry System in the ACC or ON/
When the power window lock switch is in the
RUN mode. Occupants, particularly
locked position, the light on the passenger
unattended children, can become
power window switch turns off. The light may
entrapped by the windows while operating
be difficult to see depending on the
the power window switches. Such
surrounding brightness.
entrapment may result in serious injury or
death.
CONVERTIBLE TOP (SOFT
TOP)
Power Window Lock Switch
This feature prevents the passengers power
Lowering The Convertible Top
window from operating. Keep this switch in the
Lock Release Latch
locked position while children are in the vehicle.
WARNING!
† Locked Position (Button Pushed): only the
1 — Release Latch Closed
Do not sit on the folded convertible top,
driver's power window can be operated.
2 — Release Latch Open (Red Indicator
otherwise the convertible top could be
Visible)
damaged or you may fall off and be
† Unlocked Position (Button Not Pushed): both
injured.
power windows on each door can be operated.
59

-------------------------------------------------------------------------------------------------------------------------------------------------------------

4. With the lock release latch pushed
NOTE:
8. With the back end of the convertible top
forward (red indicator visible), pull the
The power windows will go down automati-
pushed down, push the front end until a
top latch handle rearward to unlock it.
cally when the convertible top is opened. If
latching sound is heard. Lightly rock the
the power windows do not go down automat-
retracted convertible top to make sure it
ically, fully open the windows using the
is securely locked.
power window switch located on the doors.
6. Standing outside of the vehicle, hold the
convertible top along the front edge and
pull it toward the rear of the vehicle. To
lower the convertible top from inside the
vehicle, use the convertible top handles.
Pulling The Top Latch Handle Rearward
5. Remove the striker from the anchor.
Retracted Convertible Top
WARNING!
† Always keep your hands and fingers away
from the fastening mechanisms when
moving the convertible top: it is
Convertible Top Handles
dangerous to place your hands or fingers
near the fastening mechanisms. Your
7. Move the convertible top rearward while
hands or fingers could be caught and
pushing the rear glass lightly with your
injured by the mechanism.
hand.
Removing Striker From Anchor
(Continued)
1 — Anchor
2 — Striker
60

-------------------------------------------------------------------------------------------------------------------------------------------------------------

4.
While sitting in a seat, grasp the convert-
WARNING! (Continued)
ible top handles, and push the convert-
† Sit in the seat with the seat belt correctly
ible top against the windshield. Make
fastened when the vehicle is moving:
sure the striker engages with the anchor,
standing in the vehicle, or sitting on the
move the top latch slowly, and then push
convertible top storage area or center
the top latch upward until a latching
console when the vehicle is moving is a
sound is heard.
dangerous way to ride. During a sudden
maneuver or collision you could be seri-
ously injured or even killed.
Unlock Lever
Raising The Convertible Top
3.
Standing outside of the vehicle, hold the
convertible top along the front edge and
To raise the convertible top, proceed as
pull it towards the vehicle front. To raise
follows:
the convertible top from inside the
1. Make sure the parking brake is applied
vehicle, use the convertible top handles.
and the ignition is placed in the OFF
position.
Pull Top Latch Handle Forward
2. Pull the unlock lever upward to disen-
gage the lock.
Convertible Top Handles
61

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5.
If the red indicator is visible on the lock
water. Otherwise, water may enter the
† Secure all loose objects inside before
release button, the convertible top is not
vehicle. Refer to “Convertible Top Mainte-
driving with the convertible top down.
locked. After locking the convertible top,
nance” in “Servicing And Maintenance”.
† To help prevent theft or vandalism and to
verify that the red indicator is not visible.
† The convertible top may be constricted if
ensure that the passenger compartment
it is left retracted for a long period. There-
stays dry, close the convertible top
fore, if the top has become constricted, it
securely and lock both doors when leaving
may be difficult to hook the top latch
the vehicle.
striker to the anchor.
† The soft top is made of high quality mate-
† Make sure the convertible top is securely
rial and if it is not maintained correctly,
locked by pushing up on it. If it still
the material could harden, becomes
sounds loose (rattles) after being locked
stained, or have an uneven gloss.
by the top latch, contact an authorized
† Lowering the convertible top while it's wet
dealer.
can also cause water to drip into the cabin.
Lock Release Button
Convertible Top Precautions
† The power windows go down automatically
1 — Release Latch Locked
in conjunction with the convertible top
† Remove leaves or other debris that may
2 — Release Latch Unlocked (Red Indica-
opening/closing. However, this is a func-
accumulate on and around the convertible
tor Visible)
tion for improving the operability, and it
top. If leaves or other debris block the
drain filter, water may enter the vehicle.
does not mean there is a problem. If the
vehicle battery is disconnected for vehicle
Clean the drain filter at least once a year.
CAUTION!
maintenance or other reasons, the power
† Before lowering or raising the convertible
windows will not go down automatically. If
Driving with the convertible top not fully
top, stop in a safe place off of the road and
the power windows do not go down, the
locked could damage the convertible top.
park on a level surface.
automatic open/close mechanism for the
windows must be reset.
† When lowering the convertible top, make
NOTE:
sure objects inside the vehicle are not
† Do not spray water directly near the seam
blown away by the wind.
of the window and convertible top when
flushing away dirt on the soft top with
62

-------------------------------------------------------------------------------------------------------------------------------------------------------------

† The windblocker reduces the amount of
2.
Move to the outside of the vehicle and
CAUTION! (Continued)
wind coming into the cabin from behind
insert your hand into the hood opening,
when driving with the convertible top
† Do not raise or lower the convertible top in
then slide the latch lever to the right, and
opened.
a strong wind as it could damage the
lift up the hood.
convertible top or cause an unexpected
† Before starting the vehicle make sure the
accident.
convertible top is correctly locked.
CAUTION!
HOOD
† Before opening the convertible top, make
Opening The Hood
sure the rear window defroster switch is
turned off. Otherwise the heat generated
To open the hood, proceed as follows:
from the window defroster could damage
1.
With the vehicle in PARK, pull the
the convertible top and the internal mate-
release handle located to the left of the
rial.
Sliding The Latch Lever To The Right
steering wheel, below the instrument
† Make sure nothing is on the convertible top
panel.
3.
Pull up the support rod from the clip, and
or near the back window when raising or
insert it into the support rod hole indi-
lowering the convertible top. Even small
cated by the arrow to hold the hood open.
objects may interfere and cause damage.
† Do not drive through an automatic car
wash; it may damage the convertible top.
† Do not raise or lower the convertible top
when the temperature is below 41°F (5°C);
this will damage the convertible top mate-
rial.
† Do not lower the convertible top when it's
Releasing The Hood Latch
wet. If the convertible top dries while
folded, it will deteriorate and mold.
Support Rod
(Continued)
63

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING!
WARNING! (Continued)
Be sure the hood is fully latched before
† Be careful when opening/closing the
driving your vehicle. If the hood is not fully
trunk lid during strong winds. If a strong
latched, it could open when the vehicle is
gust blows against the trunk lid, it could
in motion and block your vision. Failure to
close suddenly resulting in injury.
follow this warning could result in serious
† Fully open the trunk lid and make sure
injury or death.
that it stays open. If the trunk lid is only
opened partially, it could slam shut by
CAUTION!
vibration or wind gusts resulting in
Inserting Support Rod Into Hole
injury.
To prevent possible damage, do not slam
Closing The Hood
the hood to close it. Lower hood to
† When loading or unloading luggage in
To close the hood, proceed as follows:
approximately 8 inches (20 cm) and drop
the trunk, turn off the engine. Otherwise,
the hood to close. Make sure hood is fully
you could get burned by the heat of the
1.
Check under the hood area to make
closed for both latches. Never drive
exhaust gas.
certain all filler caps are in place and all
vehicle unless hood is fully closed, with
loose items
(e.g. tools, oil containers,
both latches engaged.
Using The Remote
Release
Button
— If
etc.) have been removed.
Equipped
2.
Lift the hood with one hand, and with the
TRUNK LID
other hand grasp the padded area on the
support rod.
Opening
3.
Secure the support rod into the rod clip.
WARNING!
4.
Verify that the support rod is secured in
† Before opening the trunk lid, remove any
the clip before closing the hood.
snow and ice accumulation on it. Other-
wise, the trunk lid could close under the
5.
Lower the hood slowly to a height of
weight of the snow and ice resulting in
about 8 inches (20 cm) above its closed
injury.
Interior Trunk Lid Release Button
position and then let it drop.
(Continued)
64

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The remote release button function can be
Using The Electric Trunk Lid Opener
With The Advanced Keyless Entry Function
disabled by locking the doors using the key
With the remote release button, the trunk lid
A locked trunk lid can also be opened while
fob, emergency key, or a request switch on
can also be opened while the key fob is being
the key fob is being carried. When opening
the exterior door handle to prevent an
carried.
the trunk lid with the doors locked, it may
intruder in the vehicle from opening the
require a few seconds for the trunk lid latch
trunk lid.
Push the electric trunk lid button and raise
to release after the electric trunk lid opener
the trunk lid when the latch releases.
To enable the remote release button opera-
is pushed.
tion, unlock the doors by using the key fob,
The trunk lid can be closed when the doors
emergency key, request switch on the exte-
are locked with the key fob left in the vehicle.
rior door handle, or place the ignition in the
However, to prevent locking the key fob in
ON position.
the vehicle, the trunk lid can be opened by
NOTE:
pushing the electric trunk lid opener. If the
The remote release button cannot
be
trunk lid cannot be opened despite doing
disabled by locking the doors using
the
this procedure, push the electric trunk lid
door-lock switch/door-lock knob.
opener to fully open the trunk lid after
pushing the trunk lid completely closed.
Electric Trunk Release Button
If the vehicle battery is depleted or there is a
malfunction in the electrical system and the
Without the remote release button, unlock
trunk lid cannot be unlocked, the trunk lid
the doors and trunk lid, then push the elec-
can be opened by performing the emergency
tric trunk lid opener and raise it when the
procedure.
latch releases.
65

-------------------------------------------------------------------------------------------------------------------------------------------------------------

When Trunk Lid Cannot Be Opened
2.
Remove the fasteners on the right side of
4. Turn and loosen the cap screws until the
the vehicle.
screws start to spin free.
If the battery is discharged, the trunk lid
cannot be unlocked and opened.
NOTE:
Do not pull the screw when pulling the cap.
If the trunk lid cannot be unlocked even if
Otherwise, the screw may fall off and
the discharged battery situation has been
become lost.
resolved, the electrical system may have a
malfunction.
Refer to “Trunk Emergency Release” in this
chapter for further information.
Proceed as follows:
Closing
1. Close the convertible top and remove the
windblocker.
1. Use both hands to push the trunk lid
Remove Fasteners
down until the lock snaps shut. Do not
slam it.
3.
Partially peel back the cover on the right
side of the vehicle.
2. Pull up on the trunk lid to check if it is
secure.
Remove Windblocker
Cover Removal
66

-------------------------------------------------------------------------------------------------------------------------------------------------------------

TRUNK EMERGENCY
Trunk Safety Warning
RELEASE
WARNING!
As a security measure, a emergency release
Do not allow children to have access to the
trunk, either by climbing into the trunk
lever is built into the rear tail panel of the
trunk. In the event of an adult or child being
from outside, or through the inside of the
vehicle. Always close the trunk lid when
locked inside the trunk, the trunk can be
simply opened by pulling down the lever and
your vehicle is unattended. Once in the
trunk, young children may not be able to
open the trunk lid. After performing this
emergency measure, contact an authorized
escape, even if they entered through the
HomeLink® Buttons
rear seat. If trapped in the trunk, children
dealer as soon as possible.
can die from suffocation or heat stroke.
1 — Homelink® Button 1
2 — Homelink® Button 2
GARAGE DOOR OPENER —
3 — Homelink® Button 3
IF EQUIPPED
NOTE:
HomeLink® is disabled when the Vehicle
HomeLink® replaces up to three hand-held
Security Alarm is active.
transmitters that operate devices such as
garage door openers, motorized gates,
Before You Begin Programming
lighting or home security systems. The
HomeLink®
HomeLink® unit is powered by your vehicle’s
Trunk Emergency Release
Be sure that your vehicle is parked outside of
12 Volt battery.
the garage before you begin programming.
The HomeLink® buttons, located on the
For more efficient programming and accu-
auto-dimming mirror, designate the three
different HomeLink® channels. The Home-
rate transmission of the Radio Frequency
(RF) signal it is recommended that a new
Link® indicator is located near the center
button.
battery be placed in the hand-held trans-
mitter of the device that is being
programmed to the HomeLink® system.
67

-------------------------------------------------------------------------------------------------------------------------------------------------------------

To erase the channels, place the ignition in
NOTE:
3.
Push and hold the HomeLink® button
the ON position, and push and hold the two
It is NOT the button that is normally used to
you want to program while you push and
outside HomeLink® buttons (1 and 3) for up
open and close the door. The name and color
hold the hand-held transmitter button.
to 20 seconds or until the orange indicator
of the button may vary by manufacturer.
flashes.
4.
Continue to hold both buttons and
observe the indicator light. The Home-
NOTE:
Link® indicator will flash slowly and then
rapidly after HomeLink® has received
† Erasing all channels should only be
the frequency signal from the hand-held
performed when programming Home-
transmitter. Release both buttons after
Link® for the first time. Do not erase
the indicator light changes from slow to
channels when programming additional
rapid.
buttons.
† If you have any problems, or require assis-
5.
On the garage door opener
(in the
tance,
please
call
toll-free
garage), locate the
“LEARN” or
Training The Garage Door Opener
1-800-355-3515 or, on the Internet at
“TRAINING” button. This can usually be
HomeLink.com for information or assis-
found where the hanging antenna wire is
1 — Door Opener
tance.
attached to the garage door opener/
2 — Training Button
device motor. Firmly push and release
Programming A Rolling Code
the “LEARN” or “TRAINING” button. On
For programming these garage door openers,
some garage door openers/devices there
Garage door openers that were manufactured
proceed as follows:
may be a light that blinks when the
after
1995 can be identified by the
garage door opener/device is in the
“LEARN” or “TRAIN” button located where
1. Place the ignition in the ON position.
LEARN/TRAIN mode.
the hanging antenna is attached to the
2. Place the hand-held transmitter
1 to
garage door opener.
NOTE:
3 inches (3 to
8 cm) away from the
You have 30 seconds in which to initiate the
HomeLink® button you wish to program
next step after the LEARN button has been
while keeping the HomeLink® indicator
pushed.
light in view.
68

-------------------------------------------------------------------------------------------------------------------------------------------------------------

6. Return to the vehicle and push the
Programming A Non-Rolling Code
and the garage door/device should
programmed HomeLink® button twice
activate when the HomeLink® button
For programming garage door openers manu-
(holding the button for two seconds each
is pressed.
factured before 1995:
time). If the garage door opener/device
† To program the two remaining Home-
activates, programming is complete.
1.
Place the ignition in the ON position.
Link® buttons, repeat each step for
To program the remaining two Home-
2.
Place the hand-held transmitter
1 to
each remaining button. DO NOT erase
Link® buttons, repeat each step for each
3 inches (3 to
8 cm) away from the
the channels.
remaining button. DO NOT erase the
HomeLink® button you wish to program
Reprogramming A Single HomeLink® Button
channels.
while keeping the HomeLink® indicator
(Non-Rolling Code)
light in view.
NOTE:
To reprogram a channel that has been previ-
If the garage door opener/device does not
3.
Press and hold the HomeLink® button
ously trained, follow these steps:
activate, push the button a third time (for
you want to program while you press and
two seconds) to complete the training.
hold the hand-held transmitter button.
1. Place the ignition in the ON position.
Reprogramming A Single HomeLink® Button
2. Press and hold the desired HomeLink®
4.
Continue to hold both buttons and
(Rolling Code)
observe the indicator light. The Home-
button until the indicator light begins to
flash after 20 seconds. Do not release
Link® indicator will flash slowly and then
To reprogram a channel that has been previ-
rapidly after HomeLink® has received
the button.
ously trained, follow these steps:
the frequency signal from the hand-held
3. Without releasing the button, proceed
1. Place the ignition in the ON position.
transmitter. Release both buttons after
with “Programming A Non-Rolling Code”
the indicator light changes from slow to
2. Push and hold the desired HomeLink®
step 2 and follow all remaining steps.
rapid.
button until the indicator light begins to
flash after 20 seconds. Do not release
Canadian/Gate Operator Programming
5.
Press and hold the programmed Home-
the button.
Link® button and observe the indicator
The programming of transmitters in Canada/
light.
United States require the transmitter signals
3. Without releasing the button proceed
to “time-out” after several seconds of trans-
with “Programming A Rolling Code” step
† If the indicator light stays on
mission.
2 and follow all remaining steps.”
constantly, programming is complete
69

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Canadian radio frequency laws require trans-
4. Watch for the HomeLink® indicator to
Reprogramming A Single HomeLink® Button
mitter signals to time-out
(or quit) after
change flash rates. When it changes, it is
(Canadian/Gate Operator)
several seconds of transmission - which may
programmed. It may take up to 30 seconds
To reprogram a channel that has been previ-
not be long enough for HomeLink® to pick
or longer in rare cases. The garage door
ously trained, follow these steps:
up the signal during programming. Similar to
may open and close while you are program-
this Canadian law, some U.S. gate operators
ming.
1. Place the ignition to the ON position.
are designed to time-out in the same
5. Press and hold the programmed Home-
2. Press and hold the desired HomeLink®
manner.
Link® button and observe the indicator
button until the indicator light begins to
It may be helpful to unplug the device during
light.
flash after 20 seconds. Do not release
the cycling process to prevent possible over-
the button.
heating of the garage door or gate motor.
NOTE:
3. Without releasing the button, proceed
1.
Place the ignition in the ON position.
† If the indicator light stays on constantly,
with “Canadian/Gate Operator Program-
programming is complete and the garage
2.
Place the hand-held transmitter
1 to
ming” step 2 and follow all remaining
door/device should activate when the
steps.
3 inches (3 to
8 cm) away from the
HomeLink® button is pressed.
HomeLink® button you wish to program
Using HomeLink®
while keeping the HomeLink® indicator
† To program the two remaining HomeLink®
light in view.
buttons, repeat each step for each
To operate, push and release the
remaining button. DO NOT erase the chan-
programmed HomeLink® button. Activation
3.
Continue to press and hold the Home-
nels.
will now occur for the programmed device
Link® button, while you press and
(i.e. garage door opener, gate operator, secu-
release
(cycle) your hand-held trans-
If you unplugged the garage door opener/
rity system, entry door lock, home/office
mitter every two seconds until Home-
device for programming, plug it back in at
lighting, etc.). The hand-held transmitter of
Link® has successfully accepted the
this time.
the device may also be used at any time.
frequency signal. The indicator light will
flash slowly and then rapidly when fully
trained.
70

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Security
† Did you unplug the device for program-
General Information
ming and remember to plug it back in?
It is advised to erase all channels before you
The following regulatory statement applies to
sell or turn in your vehicle.
If you have any problems, or require assis-
all Radio Frequency (RF) devices equipped
tance, please call toll-free 1-800-355-3515
in this vehicle:
To do this, push and hold the two outside
or, on the Internet at HomeLink.com for
buttons for 20 seconds until the orange indi-
This device complies with Part 15 of the FCC
information or assistance.
cator flashes. Note that all channels will be
Rules and with Innovation, Science and
erased. Individual channels cannot be
WARNING!
Economic
Development
Canada
erased.
license-exempt RSS standard(s). Operation
† Vehicle exhaust contains carbon
is subject to the following two conditions:
The HomeLink® Universal Transceiver is
monoxide, a dangerous gas. Do not run
disabled when the Vehicle Security Alarm is
your vehicle in the garage while program-
1. This device may not cause harmful inter-
active.
ming the transceiver. Exhaust gas can
ference, and
cause serious injury or death.
NOTE:
2. This device must accept any interference
The universal garage door opener only oper-
† Your motorized door or gate will open
received, including interference that may
ates when the engine is running for security
and close while you are programming the
cause undesired operation.
reasons associated with removable tops and
universal transceiver. Do not program
doors.
the transceiver if people, pets or other
Le présent appareil est conforme aux CNR
objects are in the path of the door or
d`Innovation, Science and Economic Devel-
Troubleshooting Tips
gate. Only use this transceiver with a
opment applicables aux appareils radio
garage door opener that has a “stop and
exempts de licence. L'exploitation est
If you are having trouble programming
reverse” feature as required by Federal
autorisée aux deux conditions suivantes:
HomeLink®, here are some of the most
safety standards. This includes most
common solutions:
1. l'appareil ne doit pas produire de brouil-
garage door opener models manufac-
lage, et
† Replace the battery in the garage door
tured after 1982. Do not use a garage
opener hand-held transmitter.
door opener without these safety
2. l'utilisateur de l'appareil doit accepter
features. Call toll-free 1-800-355-3515
tout brouillage radioélectrique subi,
† Push the LEARN button on the garage
or, on the Internet at HomeLink.com for
même si le brouillage est susceptible
door opener to complete the training for a
safety information or assistance.
d'en compromettre le fonctionnement.
Rolling Code.
71

-------------------------------------------------------------------------------------------------------------------------------------------------------------

La operación de este equipo está sujeta a las
Seat Side Compartment
WARNING!
siguientes dos condiciones:
The seat side compartment is located
Keep storage compartments closed when
1. es posible que este equipo o dispositivo
between the seats above the cupholders.
driving.
Driving with the storage
no cause interferencia perjudicial y
compartments open is dangerous. To
2. este equipo o dispositivo debe aceptar
reduce the possibility of injury in an
cualquier interferencia, incluyendo la
accident or a sudden stop, keep the
que pueda causar su operación no
storage compartments closed when
deseada.
driving.
NOTE:
Changes or modifications not expressly
CAUTION!
approved by the party responsible for compli-
Do not leave lighters or eyeglasses in the
ance could void the user’s authority to
storage compartments while parked under
operate the equipment.
Seat Side Compartment
the sun. A lighter could explode or the
plastic material in eyeglasses could
1 — Key Hole
INTERNAL EQUIPMENT
deform and crack from high temperature.
2 — Release Handle
Storage Compartments
To open, push the release handle down to
Center Console
open the seat side compartment.
The center console is located between the
Insert the emergency key in the lock and turn
driver’s and passenger’s seats.
it clockwise to lock, counter clockwise to
unlock.
NOTE:
When using the rear console cup holders,
remove any cups before opening the seat
Center Console Lid
side compartment. If the seat side compart-
72

-------------------------------------------------------------------------------------------------------------------------------------------------------------

ment is opened with a cup present, the lid
After returning the seat to its original posi-
Vanity Mirrors
will hit the cups and may cause the contents
tion, make sure the seat is secured by
To access the vanity mirror, fold the sun visor
to spill.
attempting to lightly move it forward and
down and lift the cover toward the seats.
rearward.
Back Trim Storage Compartment
Interior Lights
CAUTION!
Small items can be stored in the back trim
storage compartment which is located
Do not forcefully push objects into the rear
Overhead Light
behind the seats.
storage compartment. Otherwise, the box
The interior light is located in the headliner
could be damaged.
in between the sun visors. The interior light
can be set to three different positions.
Sun Visors
The sun visors are located at the sides of the
interior rear view mirror. They can be
adjusted forward toward the windshield, and
sideways toward the side windows to block
sunlight.
Back Trim Storage Compartment
To use the back trim storage compartment,
Overhead Light Switch
slide the seat all the way forward and fold the
seat back forward, then open the compart-
1 — On
ment.
2 — Door
When finished, close the compartment and
3 — Off
return the seat to its original position and
secure it.
Sun Visor
73

 

 

 

 

 

 

 

 

Content      ..     1      2      3      4      ..