DAF 95XF. Manual - part 530

 

  Index      DAF     DAF 95XF Series - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  528  529  530  531   ..

 

 

DAF 95XF. Manual - part 530

 

 

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

General

2-2

2.3 WARNING SYMBOL

When text is accompanied by the warning
symbol shown here, the information provided is
essential for the health and personal safety of
the mechanic.
This warning symbol is also shown if
circumstances threaten the safety of the vehicle
or could lead to damage to the vehicle.

M0015

2.4 ENVIRONMENT

By carrying out the maintenance activities in a
professional manner, on time and at regular
intervals, you will help reduce the impact on the
environment.
This means, for example, noticing and
remedying possible leakages in time and
keeping the engine in an optimum condition
(adjusting valves, replacing air filter element
etc.), thus reducing the emission of harmful
exhaust gases.
It should be noted that oils and fluids contain
harmful substances that have a negative impact
on the environment.
That is why you should take care that drained
oils and fluids, but also discarded oil and fuel
filters, are collected in separate receptacles or
containers.
In short: Maintenance activities must be
carried out in an environmentally conscious
manner.

5

 200424

General

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

2-3

2.5 PARTS

All DAF parts and components have been
carefully attuned to each other, a decisive factor
in ensuring the original DAF quality.
It is only logical, therefore, that the original DAF
quality can best be maintained if original DAF
parts and components are used when replacing
parts or components.
As far as maintenance activities are concerned,
you should think of windscreen-wiper blades,
air-dryer elements, gaskets, V-belts and filters.
If, for example, non-original DAF filters are used,
the engine will be insufficiently protected against
microscopically small airborne dust particles,
almost imperceptible metal swarf in the oil and
contaminated fuel, resulting in:
-

premature replacing of cylinders, pistons,
bearings, valves, injector pump and other
moving parts

-

reduced engine performance

-

increased fuel consumption.

Therefore, always use original DAF parts and
components.

G000067

5

 200424

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

General

2-4

2.6 MAINTENANCE GUIDELINES

-

When carrying out maintenance activities
on the vehicle, it is important that the work
is performed under the cleanest possible
conditions.
Filler caps, lubricating points, level check
and drain plugs should be cleaned before
and after maintenance activities.

-

When excessive leakage has been detected
at oil seals and/or components, or in case of
excessive oil-level decreases, a report
should be made and the cause should be
remedied.

-

It is important to check the exhaust ports of
the gearbox, transfer case, rear axle and
driven front axle regularly for fouling and
blocking.
If the breathers are blocked by dirt,
overpressure could cause leakage.

-

Depending on the circumstances in which
the vehicle is used, e.g. on very bad roads
or construction sites, important bolt
connections such as the fifth wheel, spring
suspension, U-bolts, trailer coupling,
steering box attachment, superstructure
attachments etc. should be inspected more
often and, if required, be retightened.

-

It is important that a visual inspection and
test run are carried out following the
maintenance activities.
Particular attention should be paid to
components directly related to driving
safety.

-

Consult the DAF workshop instructions
when welding at and/or drilling in the
chassis.
Welding to and/or drilling in wrong spots of
the chassis will cause the material to
weaken.

5

 200424

General

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

2-5

-

Always make sure that when welding at the
vehicle the alternator wiring and the positive
and negative battery leads are
disconnected.
Position the earth clamp as close as
possible to the weld location. The earth
clamp must never be attached to a rotating
component such as propeller shaft, hub, fan
etc.,
nor on an autonomous operating
component in which there are rotating parts
such as the compressor, turbo etc..

5

 200424

 

 

 

 

 

 

 

Content   ..  528  529  530  531   ..