Chrysler Pacifica. Manual - part 236

 

  Index      Chrysler     Chrysler Pacifica - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  234  235  236  237   ..

 

 

Chrysler Pacifica. Manual - part 236

 

 

Symptom List:

DRIVER FRONT RISER AND PEDAL FORWARD SWITCH OPEN -
DDM
DRIVER HORIZONTAL AND LUMBAR IN SWITCH OPEN - DDM
DRIVER REAR RISER AND PEDAL BACK SWITCH OPEN - DDM
DRIVER RECLINER AND LUMBAR OUT SWITCH OPEN - DDM
MEMORY SWITCH OPEN - DDM

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be DRIVER FRONT RISER AND
PEDAL FORWARD SWITCH OPEN - DDM.

When Monitored and Set Condition:

DRIVER FRONT RISER AND PEDAL FORWARD SWITCH OPEN - DDM

When Monitored:

Continuously.

Set Condition:

If the switch MUX circuit is over 4.9 volts for over 10 second, this code will

set.

DRIVER HORIZONTAL AND LUMBAR IN SWITCH OPEN - DDM

When Monitored:

Continuously.

Set Condition:

If the switch MUX circuit is over 4.9 volts for over 10 second, this code will

set.

DRIVER REAR RISER AND PEDAL BACK SWITCH OPEN - DDM

When Monitored:

Continuously.

Set Condition:

If the switch MUX circuit is over 4.9 volts for over 10 second, this code will

set.

DRIVER RECLINER AND LUMBAR OUT SWITCH OPEN - DDM

When Monitored:

Continuously.

Set Condition:

If the switch MUX circuit is over 4.9 volts for over 10 second, this code will

set.

MEMORY SWITCH OPEN - DDM

When Monitored:

Continuously.

Set Condition:

If the switch MUX circuit is over 4.9 volts for over 10 second, this code will

set.

POSSIBLE CAUSES

DTC PRESENT

941

POWER SEATS

POSSIBLE CAUSES

DRIVER SEAT SWITCH

SWITCH MUX WIRE OPEN

SWITCH MUX WIRE SHORT TO VOLTAGE

DRIVER DOOR MODULE

SEAT SWITCH MUX RETURN OPEN

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, erase DTCs.

Cycle the ignition switch from Off to Run.
Operate the switch indicated by the DRBlll

t in all positions several times.

With the DRBIII

t, read DTCs.

Does the DRBIII

t display the same DTC?

All

Yes

→ Go To 2

No

→ The condition that caused this code to set is not present at this

time. Review wiring schematics and inspect related wiring for an
intermittent condition.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.

2

Turn the ignition on.
With the DRBIII

t in Sensors, read the Seat Switch voltage of the switch that had the

DTC.
Select the voltage displayed.

All

4.4 to 5.1 volts.

Go To

3

Over 5.2 volts

Go To

5

3

Disconnect the Driver Seat Switch connector.
Turn the ignition on.
Measure the voltage of the Switch MUX circuit indicated by the DRBlll

t and ground.

Is the voltage between 4.4 and 5.1 volts?

All

Yes

→ Go To 4

No

→ Repair the Switch MUX wire for an open.

Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Driver Seat Switch connector.
Measure the resistance of the Seat Switch MUX Return circuit in the switch
connector to ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Driver Seat Switch.

Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.

No

→ Repair the Seat Switch MUX Return for an open.

Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.

942

POWER SEATS

DRIVER FRONT RISER AND PEDAL FORWARD SWITCH OPEN - DDM —

Continued

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect the Driver Seat Switch connector.
Disconnect the Driver Door Module C2 connector.
Inspect the Seat Switch MUX circuit that had the DTC for a possible short to voltage.
Were there any problems found?

All

Yes

→ Repair the MUX circuit for a short to voltage.

Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.

No

→ Replace the Driver Door Module.

Perform BODY VERIFICATION TEST - VER 1.

943

POWER SEATS

DRIVER FRONT RISER AND PEDAL FORWARD SWITCH OPEN - DDM —

Continued

Symptom:

DRIVER FRONT RISER AND PEDAL FORWARD SWITCH SHORT -
DDM

When Monitored and Set Condition:

DRIVER FRONT RISER AND PEDAL FORWARD SWITCH SHORT - DDM

When Monitored:

Continuously.

Set Condition:

If the MUX circuit is under 0.10 volt for over 10 seconds, this code will set.

POSSIBLE CAUSES

DTC PRESENT

DRIVER POWER SEAT SWITCH

DRIVER SEAT FRONT RISER/PEDAL FORWARD SWITCH MUX

DRIVER DOOR MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, erase DTCs.

Cycle the ignition switch from Off to Run.
Operate the Seat Switch in all positions several times.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display DRIVER FRONT RISER AND PEDAL FORWARD

SWITCH SHORT?

All

Yes

→ Go To 2

No

→ The condition that caused this code to set is not present at this

time.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.

2

Disconnect the Driver Power Seat Switch connector.
Turn the ignition on.
With the DRBIII

t, erase DTCs.

Cycle the ignition switch from Off to Run and wait 10 seconds.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display DRIVER FRONT RISER AND PEDAL FORWARD

SWITCH SHORT?

All

Yes

→ Go To 3

No

→ Replace the Driver Power Seat Switch.

Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.

944

POWER SEATS

 

 

 

 

 

 

 

Content   ..  234  235  236  237   ..