Chrysler New Yorker. Manual - part 365

TEST 4A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED

Perform TEST 1A Before Proceeding

FIG. 1

A

I

R
B
A

G

S
Y
S

T

E

M

58

TEST 4A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-1A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION 

WARNING: DISCONNECT 

OF ALL COMPONENTS.

THE BATTERY AND WAIT 

START TEST 4A.

2 MINUTES BEFORE 

PROCEEDING.

SEE GENERAL INFO 4.0

ENSURE THE DRIVER 

IS COMPLETELY 

AIRBAG MODULE 

CONNECTED BEFORE 

WAS THE CONNECTOR

NO 

CONNECT AIRBAG 

SQUIB HARNESS

DISCONNECTING IN COMPLETELY 

MODULE.* 

CONNECTOR... NEXT 

STEP.

CONNECTED? 

YES

DISCONNECT THE
DRIVER AIRBAG 

MODULE SQUIB

HARNESS

CONNECTOR.** 

TURN IGNITION ON.

DOES THE DRB

(ENGINE OFF).

WITH THE DRB, READ 

DISPLAY

YES

REPLACE DRIVER 

THE ACTIVE CODES. 

"DRIVER SQUIB

AIRBAG MODULE.* 

RECONNECT THE

CIRCUIT OPEN"? 

BATTERY. 

NO 

DISCONNECT THE

DOES THE DRB

CLOCKSPRING 2-WAY

WITH THE DRB, READ 

DISPLAY

YES

REPLACE THE

HARNESS

THE ACTIVE CODES. 

"DRIVER SQUIB

CLOCKSPRING.*

CONNECTOR.** CIRCUIT OPEN"? 

NO 

TURN IGNITION OFF. 

MEASURE BETWEEN THE

CHECK THE DRIVER 

DRIVER AIRBAG LINE 1

IS THE RESISTANCE 

YES

AIRBAG LINE 1

WITH AN 

AND LINE 2 CKTS AT 

BELOW 5.0 OHMS?

CIRCUIT FOR A

OHMMETER...

THE CLOCKSPRING

SHORT TO LINE 2

HARNESS CONN. FIG. 1

CIRCUIT. 

NO 

INSPECT THE

SHORTING CLIP FOR

DAMAGE. IF NO 

SHORT IS FOUND, 

REPLACE THE ACM.*

PERFORM TEST 

19A. 

A

I

R
B
A

G

S
Y
S

T

E

M

59

TEST 5A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED TO BATTERY

Perform TEST 1A Before Proceeding

FIG. 1

A

I

R
B
A

G

S
Y
S

T

E

M

60

TEST 5A

REPAIRING DRIVER SQUIB CIRCUIT SHORTED TO BATTERY

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-1A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION 

WARNING: DISCONNECT 

DISCONNECT THE

OF ALL COMPONENTS.

THE BATTERY AND WAIT 

DRIVER AIRBAG 

START TEST 5A.

2 MINUTES BEFORE 

MODULE SQUIB

PROCEEDING.

HARNESS

SEE GENERAL INFO 4.0

CONNECTOR.** 

TURN IGNITION ON 

DOES THE DRB

(ENGINE OFF).

WITH THE DRB, READ 

DISPLAY

NO 

REPLACE THE DRIVER 

THE ACTIVE CODES. 

"DRIVER SQUIB

AIRBAG MODULE.* 

RECONNECT THE

CIRCUIT SHORTED TO 

BATTERY. BATTERY"?

YES

DISCONNECT THE

DOES THE DRB

CLOCKSPRING 2-WAY

WITH THE DRB, READ 

DISPLAY

NO 

REPLACE THE

HARNESS

THE ACTIVE CODES. 

"DRIVER SQUIB

CLOCKSPRING.*

CONNECTOR.** CIRCUIT SHORTED TO 

BATTERY"?

YES

WARNING: DISCONNECT 

DISCONNECT THE

TURN THE IGNITION 

THE BATTERY AND WAIT 

AIRBAG CONTROL

ON.

2 MINUTES BEFORE 

MODULE 23-WAY 

PROCEEDING.

HARNESS

RECONNECT THE

CONNECTOR.** BATTERY. 

USING A VOLTMETER, BETWEEN THE

REPAIR 

DRIVER 

MEASURE THE DRIVER 

CLOCKSPRING 2-WAY

IS THE VOLTAGE

YES

AIRBAG LINE 1

AIRBAG 

HARNESS CONNECTOR

ABOVE 0.5 VOLTS ON 

CIRCUIT OR LINE 2

LINE 1 CKT AND

AND GROUND.

EITHER CIRCUIT? 

CIRCUIT FOR A

THEN LINE 2 CKT... 

FIG. 1

SHORT TO VOLTAGE.*

NO 

PERFORM TEST 

19A. 

A

I

R
B
A

G

S
Y
S

T

E

M

61