Land Rover Engine 1.8 Litre K Series. Manual - part 5

 

  Index      Land Rover     Land Rover Engine 1.8 Litre K Series - service manual 2000 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  3  4  5  6   ..

 

 

Land Rover Engine 1.8 Litre K Series. Manual - part 5

 

 

ENGINE

6

OVERHAUL

23. Ensure inserts are fitted in timing belt upper

front cover.

24. Fit timing belt upper front cover, ensuring

correct position of seals, tighten screws and
bolt to 5 Nm.

Camshaft timing belt - automatic tensioner -
remove

CAUTION: Timing belts fitted to engines
with automatic timing belt tensioners are
not interchangeable with those fitted to

engines with manual tensioners.

1. Slacken but do not remove bolt securing

bottom of timing belt upper front cover.

NOTE: Remove bolt when cover is not
slotted.

2. Noting fitted position of longest screw, remove

5 screws securing timing belt upper front cover.

3. Remove timing belt upper front cover together

with seal.

ENGINE

OVERHAUL

7

4. Rotate crankshaft clockwise to align camshaft

gear timing marks - 90

°

BTDC.

CAUTION: Do not use camshaft gears,
gear retaining bolts or timing belt to rotate
crankshaft.

5. Fit camshaft gear locking tool LRT-12-134.

6. Check that timing mark on crankshaft pulley is

aligned with mark on timing belt lower cover.

7. Fit flywheel locking tool LRT-12-145, secure

with 2 bolts.

ENGINE

8

OVERHAUL

8. Remove crankshaft pulley bolt and washer.
9. Remove crankshaft pulley.

10. Remove 3 bolts securing timing belt lower

cover.

11. Remove timing belt lower cover together with

seals.

12. Remove and discard timing belt tensioner bolt.
13. Disengage index wire from its fitted position

whilst at the same time removing the timing
belt tensioner.

14. Ease timing belt from gears using the fingers

only.

15. Discard timing belt.

CAUTION: Timing belt must always be
replaced during engine overhaul. Do not
rotate crankshaft with timing belt removed

and cylinder head fitted.

ENGINE

OVERHAUL

9

Camshaft timing belt - automatic tensioner - refit

CAUTION: If the sintered gears have been
subjected to prolonged oil contamination,
they must be soaked in a solvent bath and

then thoroughly washed in clean solvent before
refitting. Because of the porous construction of
sintered material, oil impregnated in the gears
will emerge and contaminate the belt.

1. Clean timing gears, coolant pump drive gear

and tensioner pulley.

2. Check correct alignment of camshaft gear

timing marks, fit camshaft gear locking tool
LRT-12-134.

3. Check that crankshaft gear timing marks are

aligned with flange on oil pump - 90

°

BTDC.

4. Fit flywheel locking tool LRT-12-145, secure

with 2 bolts.

5. Fit timing belt tensioner ensuring that index

wire is positioned over pillar bolt and that
tensioner lever is at 9 o’clock position.

6. Fit a new tensioner securing bolt and tighten

bolt until it is just possible to move tensioner
lever.

7. Using the fingers only, fit a new timing belt over

crankshaft gear, then camshaft gears,
tensioner pulley and coolant pump drive gear
ensuring that the belt run between the
crankshaft gear and the exhaust camshaft gear
is kept taut.

8. Check that timing belt is positioned centrally

around gears and tensioner pulley.

9. Ensure inserts are fitted in timing belt lower

cover.

 

 

 

 

 

 

 

Content   ..  3  4  5  6   ..