Parker Installation and Startup Manual Hydraulic Motors Series F10/F11/F12 (2021)
Bulletin MSG30-8205-INST/EU
Installation and
Startup Manual
Visit our homepage
for additional support
Hydraulic Motors
parker.com/pmde
Series F10/F11/F12
Effective: December, 2021
Supersedes: March, 2018
Language
SE, UK, DE, FR, ES, SF, IT, RU, ZH
Bulletin MSG30-8205-INST/EU
Hydraulic Motors
Installation and Startup Manual
Series F10/F11/F12
VIKTIGT • IMPORTANT • IMPORTANTE • WICHTIG •
TÄRKEÄTÄ • ВАЖНО • 重要事项：
F11_bild.eps
SE
Rotationsriktning flödesriktning.
SE
Garantin endast giltig om pump/
Gäller både pump och motor.
motor ej är isärtagen.
UK Direction of rotation corresponding
UK The guarantee is only valid if the
FLOW direction. Apply to both pump
pump/motor has not been
and motor.
disassembled.
DE Drehrichtung entsprechend der
DE Die Garantie gilt nur, wenn Pumpe/
Durchflußrichtung. Paßt sowohl
Motor nicht zerlegt sind.
für Pumpe als auch Motor.
FR
La garantie est valable uniquement
FR
Sens de rotation - Sans de débit
moteur/pompe non démonté(e).
correspondant - Valable également
ES
La garantía solo es válida si
pour les pompes et les moteurs.
la bomba/el motor no ha sido
ES
El sentido de giro corresponde a
desarmada/o.
la dirección del caudal. Esto es
SF
Takuun voimassaolo päättyy, jos
aplicable tanto en bombas como
pumppua/moottoria on purettu.
en motores.
IT
La garanzia è valida a condizione
SF
Pyörimissuunta virtaussuunta. Kos-
che pompa/motore non siano smon-
kee sekä pumppua että moottoria.
tati.
IT
Senso di rotazione in funzione della
RU Гарантия распространяется
direzione di mandata. Vale indiffe-
только на насосы / двигатели,
rentemente, sia come pompa, che
которые не были разобраны.
come motore.
ZH
泵/马达仅在未拆解的情况下才提供
RU Направление вращения
保修
соответствует направлению
ПОТОКА. Это относится и к
насосу, и к двигателю.
ZH
适用于泵与马达工况
2
Bulletin MSG30-8205-INST/EU
Hydraulic Motors
Installation and Startup Manual
Series F10/F11/F12
SE
Använd våra rekommenderade led-
SF
Käytä suosittelemamme kokoisia
ningsdimensioner. Smala suglednin-
putkia. Ohuet imuputket ja putki-
gar och krökar kan orsaka kavitati-
käyrät voivat aiheuttaa kavitaatiota,
on, som medför oljud och skador.
seurauksena melua ja vaurioita.
UK Follow our recommendations regar-
IT
Seguire le nostre raccomandazio-
ding pipe dimensions. Narrow pipes
ni cigca ii dimensionamento del
and bends can cause cavitation,
diametri delle tubazioni. Diametri
which will generate unnecessary
insufficenti e curve strette possono
noise and damage.
creare cavitazione. e conseguente-
DE Beachten Sie unsere Empfehlun-
mente rumorosita superflua e ulte-
gen bezüglich Rohrabmessungen.
riori danni.
Dünne Rohre und starke Biegungen
RU Следуйте нашим рекомендациям,
können Kavitationen hervorrufen,
касающимся размеров труб.
die unnötige Geräusche und Schä-
Тонкие трубы и значительные
den verursachen.
сгибы могут привести к
FR
Prière de suivre nos recommanda-
кавитации, вызывающей
tions concernant les diamètres des
ненужные шумы и повреждения.
tuyauteries. Des coudes et des tuyaux
ZH
关于管道尺寸，请遵循我们的建议，
de diamètre trop réduit donnent lieu å
管径太小或者弯头会形成气蚀， 从
du bruit et provoquent éventuellement
而产生不必要的噪声和损坏
une détérioraŧion du matériel
ES
Siga nuestras recomendaciones
respecto al tamaño de fas tuberias.
Tubos y codos estrechos pueden
causar cavitación, lo cual dará lugar
a averias y ruidos innecesarios.
3
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Bulletin MSG30-8205-INST/EU
Hydraulic Motors
Installation and Startup Manual
Series F10/F11/F12
F11
F10/F12
Drain flow
Spring
loaded
check
valve
Flushing flow
Drain
(when required)
flow
SE Anslut dränerledningen till den högst
SF Littä vuotoputki pumpun/moottorin
belägna dräneranslutningen på pum-
ylimpään vuotoIiitäntään. Mikåli mah-
pen/motorn. Anslut om möjligt dräner-
dollista, liitä vuotoliitäntä suoraan
ledning direkt till tank för att undvika
säiliöön, jotta koneen pesässä et syn-
högt tryck i huset.
tyisi korkesa painetta.
UK Use the drain connection, which is
IT Usare sempre 11 drenaggio piu’ alto
positioned uppermost on the pump/
conformemente al posizionamento
motor.
delta pompa.
DE Benutzen Sie den Leckölanschluß,
RU Используйте присоединение
der je nach Einbaulage der Maschine
дренажной линии, расположенное
am höchsten liegt.
выше всего относительно места
установки насоса / двигателя.
FR Utiliser I’orifice de drain sa trouvant le
plus haut sur le moteur la pompe.
ZH 设计与连接泵/马达泄油管时要使用
ES Utilice la conexión de drenaje mås
最上部的泄油口
etta segun la posición de la bombal-
motor.
4
Bulletin MSG30-8205-INST/EU
Hydraulic Motors
Installation and Startup Manual
Series F10/F11/F12
SE
Använd olja och filter enligt våra re-
SE
Rengör hydraulsystemet noga innan
kommendationer.
olja påfylles.
UK Use oil and filter as recommended by
UK Carefully clean the hydraulic system
us.
before the system is filled with oil.
DE
Gebrauchen Sie das von uns empfoh-
DE
Säubern Sie vor Einfüllung des Öls
lene Öl und den von uns vorgeschla-
sorgfältig das System.
genen Filter.
FR
Nettoyer soigneusement le système
FR
Employer une huile et un filtre confor-
avant de la remplir d’huile.
mes å nos recommandations.
ES
Limpie minuciosamente el sistema
ES
Utilice aceites Y filtros de acuerdo
antas de ilenario de aceite.
con nuestras rocomendaciones.
SF
Puhdista hydraulijärjestelmä huolelli-
SF
Käytä suosituksemme mukaista öljyä
sesti ennen öljyllä täyttämistä.
ja suodatinta.
IT
Si raccomanda la massima pulizia,
IT
Usare I’olio e i filtri da noi raccoman-
specialmente nei rabbocchi a nel
dati.
cambio dell’olio.
RU Используйте масло и фильтр,
RU Выполните тщательную очистку
которые рекомендованы нами.
гидравлической системы, прежде
чем заполнять ее маслом.
ZH
请使用我们推荐的液压油与过滤
ZH
在系统加油之前，请确保整个液压系
统干净
SE Fyll huset med olja före start.
UK Fill the casing with oil before start up.
DE Füllen Sie vor Beginn das Gehäuse
mit Öl.
FR Remplir la carter de ta pompe ou du
moteur avant la miss en route.
ES Liene le carcasa de aceite antes de ta
puesta en marcha.
SF Täytä pesä öljyllä ennen käynnistystä.
IT Prima detta massa In funzione riempi-
re d’olio la carcassa-pompa.
RU Заполните корпус маслом перед
началом работы.
ZH 启动前，壳体装满油
5
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Bulletin MSG30-8205-INST/EU
Hydraulic Motors
Installation and Startup Manual
Series F10/F11/F12
Position notification regarding Machinery Directive 2006/42/EC:
Products made by the Pump & Motor Division Europe (PMDE) of Parker Hannifin are
excluded from the scope of the machinery directive following the “Cetop” Position Paper
on the implementation of the Machinery Directive 2006/42/EC in the Fluid Power Industry.
All PMDE products are designed and manufactured considering the basic as well as the
proven safety principles according to:
• ISO 13849-1:2015
• SS-EN ISO 4413:2010
so that the machines in which the products are incorporated meet the essential health
and safety requirements.
Confirmations for components to be proven component, e. g. for validation of hydraulic
systems, can only be provided after an analysis of the specific application, as the fact to
be a proven component mainly depends on the specific application.
Dr. Hans Haas
General Manger
Pump & Motor Division Europe
WARNING - USER RESPONSIBILITY
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and
authorized distributors provide product or system options for further investigation by users having
technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection
of the system and components and assuring that all performance, endurance, maintenance,
safety and warning requirements of the application are met. The user must analyze all aspects of
the application, follow applicable industry standards, and follow the information concerning the
product in the current product catalogue and in any other materials provided from Parker or its
subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or
system options based upon data or specifications provided by the user, the user is responsible for
determining that such data and specifications are suitable and sufficient for all applications and
reasonably foreseeable uses of the components or systems.
Offer of Sale
Please contact your Parker representation for a detailed ”Offer of Sale”.